L293D Motor Drive Shield for Arduino Uno, Mega2560
HTML-код
- Опубликовано: 3 июл 2021
- Second Part of Video
• SERVO MOTOR CONTROLLIN...
This L293D Motor Driver Shield for Arduino is probably one of the most versatile on the market and features 2 servo and 4 motor connectors for DC or stepper motors. That makes it a great shield for any robotic project.
This Arduino compatible motor Driver shield is a full-featured product that it can be used to drive 4 DC motor or two 4-wire steppers and two 5v servos. It drives the DC motor and stepper with the L293D, and it drives the servo with Arduino pin9 and pin10.
L293D is a monolithic integrated, high voltage, high current, 4-channel driver. Basically, this means using this chip you can use DC motors and power supplies of up to 36 Volts, that some pretty big motors and the chip can supply a maximum current of 600mA per channel, the L293D chip is also what’s known as a type of H-Bridge. The H-Bridge is typically an electrical circuit that enables a voltage to be applied across a load in either direction to an output, e.g. a motor.
The shield contains two L293D motor drivers and one 74HC595 shift register. The shift register expands 3 pins of the Arduino to 8 pins to control the direction of the motor drivers. The output enables the L293D is directly connected to PWM outputs of the Arduino.
Features of L293D Motor Driver Shield for Arduino:-
2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC.
Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
Pull down resistors keep motors disabled during power-up
Big terminal block connectors to easily hook up wires (18-26AWG) and power
Arduino reset button brought up top
2-pin terminal block and jumper to connect external power, for separate logic/motor supplies
Tested compatible with Arduino Mega 1280 & 2560, Diecimila, Duemilanove, and UNO 
Наука
finally after 3hours i found this tutorial video
Thank you for sharing the knowledge. please make more this type of videos..
Great job sir
Wanted the same instction for mx1919 driver ic
sir where to connect uv and ultrasonic sensors
BHAI ham pwm pin kese use kare
What is the max voltage supply for L293D sir? I really want to increase my motor speed but also afraid that my shield or arduino will be burned out
12 V max
Can we first code the Arduino an then put moto sheild
Sure , you can , in fact this is the correct procedure .
If you found this video useful please subscribe
@@YPTechDATIA but it is not working
@@YPTechDATIA but it is not working
@@TheNoobVishu there may be some issue ,first tell me what are you trying to do with driver shield
Thank You Sir..... But i have a question sir can i use this motor driver with OG555 Motor which has current 0.45A without load
No.
Sir kha hum iske 5v aur gnd pin me female header solder ker sakte hai
Bilkul
Sir is it possible to connect IR remote in this setup?
Yes you can
Great video.
But hame school project ke liye le jana hai to hame driver set karne ke Baad pc or laptop connect rakhna pade ga ya driver save hojayega. Muje only singal Servo move karna hai. Farwerd 3sec. After delay30se vapas reverse 3 sec. After 30 sec delay. Please give me technical detail. I hope u replay
Ek baar arduino me code daal dene k baad laptop nahi chahiye hoga, lekin arduino ko power dena padegi ,battery ya kisi aur cheej se . Ye driver shield arduino k sath connected rahegi
Ariduino mega me jumper wire ki theory use kar sati hai
Kya kahna chahte ho ???
I hv a question!!!
For the past few months I hv a prob in making an arduino obstacle sensing car... the prob is with the power supply!!
Thing is I'm also using the l293d motor driver sheild nd evry time I give power supply , the driver ports burns ..!! I'm using two 2200mah li ion battery nd evrytime my port burns..!!
So I was pretty surprized tht in many vids they r using two 2200mah batteries nd still ur driver sheild works fine😮😮
I would be very greatful if someone just tells me wht to give as the power supply!! 🙏🙏
First check the voltage of the battery then connect , driver shield support 12v supply .
Also check connection , due to confusion between 5v and 12v port many burn their motor driver .
For more information mail me yptechdatia@gmail.com
@@YPTechDATIA I hv already mailed u... kindly chk..
Can I give 12v external supply for L293d motor driver shield
No , use 9 v max for safer side , and 5v for arduino
Hello sir, i have some question. Can i control for speed not from code ? For example from potensiometer. Thanks
Yes , code regulate speed logically, but you can additionally potentia meter ,
I try control from labview, but for the send data with the serial the code its error. Do you have some reference for me for applicated ?
@@passingmerem8789 I did not get your point , please explain or send detail query on yptechdatia@gmail.com
Sir .. I want to control DC motor speed by potentiometer and also limit switch for direction change of two indipendently motor ... Possible?
Yes you can .
Motor sheild me reset button kya kerta hai
Jab arduino par isko mount kar doge , to arduino ko reset karne ke liye hai ye button
( ARDUINO UNO ) is me kitne dc motor laga sakte he
(SIR PLEASE HELP)
15 dc motor laga sakte he
4 DC motor
how to connect L293D Motor Driver Shield to the Raspberry Pi
Why do you need to do this , this shield is good for arduino uno my friend . Try L293D driver
@@YPTechDATIA I have project,so I need both of them to work
@@YPTechDATIA is there any way I can connect both...
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0xb1 sir muje ye error bar bar aa rahi muje lagta hai ke mere Arduino ke ic kharab ho gayi hai to kya uske ic change ker sakte hai lekin wo Arduino uno smd hai (chip ic )
Send your arduino photo to yptechdatia@gmail.com
Bej diya sir
@@komalyadav1720 is type k arduino me kuch naHi kar sakte , naya le ko ab
Thanks sir
Sir My One Problem Solution Find Me Please Sir Motor Driver L293D Shield Is Canect On Arduino Uno Problem Is Motor Driver All Ic is Very high Hit When A Problem Solution Please sir Reply 🙏😢
I made a video how to check your motor driver , please check in playlist
@@YPTechDATIA Thank You Sir 🙏❤️
Sir kya issey dvd player ke loader ko chala sakte hai?
Dvd player ka loader bhi simple dc motor se chalta hai so technically chala sakte ho,
@@YPTechDATIA but sir speed kya rakhenge agar hame lens se bhi kaam lena hai to Matlab ek cd player hi banane ka soche to aisa kar sakte hai kya?
Uske liye ek dvd player jo working ho uski motor ko dekh kar rpm naam lena , ya voltmeter se dekh lena use kitna volt mil raha hai, fir utni speed pr ghumane k liye , speed set karna program me
Lekin agar dvd player banana hai to sirf motor ghumane k liye koi motor driver kyu use karega, ye to socho
@@YPTechDATIA ok sir 👍🏻 mpeg card hi thik hai fir to
Ham digital pin kese use kare is motor driver shield me
Arduino k ooper jo pin hai motor driver shield ki usme wire ko soldier kar do . Simple
Aaj hi voh Kia kafi hard he magar karlia thanx
Aur ek easy method bolraha hu aapke help kilie
Thodi to space he na digital pin se jo electronics part ka distance ka to us space me drill karke pin connector lagake dono kohi solder kar dijie
@@infinityfx8234 good
how i call u ? i want 2 sevo moter control
I don't sell , but if you wish to buy there are many sites like robu.in
Arduino nano ke sath connect kr sakte hai kya
Nahi, ye arduino uno par hi fit hota hai , usi k size ka hai
@@YPTechDATIA sir fit na ho lekin kya connect ho sakta hai..otherwise i have to use 1 nano for transmitter and uno for receiver..or kya nano and uno apas mai connect ho sakta hai.
@@option7484 what are you trying to make ? Please clear
I want to make a rc truck in witch i want to use 3 motors 1 servo, 2 dc 12v rs555 or 775, ..led lights horn..etc
@@option7484 ok but for this you needn't to use 2 arduino , only one nodemcu and 1 l293d driver is enough
Sir L293d ic heat hoti hai
What is solution
Heat sink tightly lagi hai ye dekh lo, and apply thermal paste on IC