Settings at the moment, sets the speed (mm per minute) in manual mode. I am still working on this, I have run out of memory on the NANO. I have ordered some memory and am hoping to be able to use it to store plots, so I can use it without connecting it to a computer.
@@Tims_Projects look like your motor including CD/DVD how much A and Volt, my powersupply 12V/24A connect arduino uno cnc shield v3 ,when sending code stepper temp very hot ,maybe burn fingers
@@danyarsniper8793 it will get hot with that board (you will fry an egg), I have not seen anyone using L293D do it right yet. the amps need to be limited to 0.4 amps. Can you make a photo to show how you are doing, so I can think the best way to continue. You may need to get some parts I used. 2 off these: www.ebay.co.uk/sch/i.html?_from=R40&_sacat=0&_nkw=L293D+Mini+Motor+Drive+Shield&_sop=15 They are same as what you have but these can be modified if you have good soldering skills. Also needed are two 2 watt 12 ohm resistors: www.ebay.co.uk/itm/20pcs-2W-Metal-Film-Resistor-Tolerance-1-Full-Range-of-Values-0-1Ω-to-1-5MΩ/172618265798?ssPageName=STRK%3AMEBIDX%3AIT&var=471438363172&_trksid=p2060353.m2749.l2649 Are you good with electronics? do you have electrical projects and things. I am trying to find out how much info I need to tell you. do you have things like L7805. Your reply's are a little short :) If you show me what you have I will start editing my blog here: tims-mini-plotter2.blogspot.com/2019/01/tims-mini-plotter-2-this-is-new-project.html and we can continue this there, with me showing you what to do.
![Tim's DFPlayer Plus [Talking about it]](http://i.ytimg.com/vi/b7V-F2B8JcI/mqdefault.jpg)
![Seungmin "그렇게, 천천히, 우리(As we are)" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/kAzmhLHePqU/mqdefault.jpg)
How should I assemble it? (instructions)
I have now done an improved one and Instructable: www.instructables.com/Tims-Mini-Plotter-2-With-Single-PCB/
Is good , what about settings ??
Settings at the moment, sets the speed (mm per minute) in manual mode.
I am still working on this, I have run out of memory on the NANO.
I have ordered some memory and am hoping to be able to use it to store plots, so I can use it without connecting it to a computer.
@@Tims_Projectsbut my cnc Motor so hot what's problem?
@@danyarsniper8793 I need More information. I don't know what you have?
@@Tims_Projects look like your motor including CD/DVD how much A and Volt, my powersupply 12V/24A connect arduino uno cnc shield v3 ,when sending code stepper temp very hot ,maybe burn fingers
@@danyarsniper8793 it will get hot with that board (you will fry an egg), I have not seen anyone using L293D do it right yet. the amps need to be limited to 0.4 amps.
Can you make a photo to show how you are doing, so I can think the best way to continue.
You may need to get some parts I used. 2 off these: www.ebay.co.uk/sch/i.html?_from=R40&_sacat=0&_nkw=L293D+Mini+Motor+Drive+Shield&_sop=15
They are same as what you have but these can be modified if you have good soldering skills.
Also needed are two 2 watt 12 ohm resistors: www.ebay.co.uk/itm/20pcs-2W-Metal-Film-Resistor-Tolerance-1-Full-Range-of-Values-0-1Ω-to-1-5MΩ/172618265798?ssPageName=STRK%3AMEBIDX%3AIT&var=471438363172&_trksid=p2060353.m2749.l2649
Are you good with electronics? do you have electrical projects and things. I am trying to find out how much info I need to tell you. do you have things like L7805.
Your reply's are a little short :)
If you show me what you have I will start editing my blog here: tims-mini-plotter2.blogspot.com/2019/01/tims-mini-plotter-2-this-is-new-project.html
and we can continue this there, with me showing you what to do.