Solder SMD using SMD/SMT Stencil!

Check out JLCPCB
$2 PCB Prototype (10pcs,10*10cm): jlcpcb.com
More project information(Code,Schematic,Details,etc):- www.instructab...
Website,
NematicsLab.com
Patreon,
/ nematicslab
For Sponsorships or Endorsements ONLY!
[e-mail]
For project-related questions use Facebook or Twitter @NematicsLab
Electronics Starter kit Tools:
Soldering Iron - www.banggood.i...
Solder wire - www.banggood.i...
Helping Hands - www.banggood.i...
Hot Glue - www.banggood.i...,
NematicsLab.com
Patreon,
/ nematicslab
For Sponsorships or Endorsements ONLY!
[e-mail]
For project-related questions use Facebook or Twitter @NematicsLab
Electronics Starter kit Tools:
Soldering Iron - www.banggood.i...
Solder wire - www.banggood.i...
Helping Hands - www.banggood.i...
Hot Glue - www.banggood.i...
In my Previous tutorials, I have shown you have to How to Solder THT & How to Solder SMD Components. which is a pretty straightforward method and works fine if you want to solder only one board, but let's say you want to solder dozens of the board then it can be a very tedious and time-consuming method. That is where an SMT Stencil can be a life savior and save you a lot of time. so in this tutorial, I will show you how to solder SMD components using SMD Stencil!
So let's begin!
------------------
--------- Affiliate ---------
Gearbest- bit.ly/2KD54KD
Banggod- bit.ly/2xgJIK5
LCSC - bit.ly/2KD0hJ0
--------- Social Media ---------
Facebook - bit.ly/2FC5lJz
Instagram - bit.ly/2XddQpe
Twitter - bit.ly/2IUhqMm

[@slaveNo-4028]

3:36, would the solder bridge/blob on the (what I guess is callen an IC) cause a short?

[@JailbreakTips]

yes

[@siboneyyy]

obviously - I couldnt stop watching that spot

[@Sysshad]

What temperature do you use for hot air

[@Analyticalbynature]

Thanks

[@parameshpavin2708]

Nice video I liked it very much 👌👍💗

[@EforEngineering]

Next project idea-Solar charge controller

[@navneetbrar1605]

Great work sir... I have to test an ATAES132A crytpo IC... This IC works on SPI communication protocol..I wanted to know that for connections we just need to attach the jumpers like this...or we have to add capacitors to the ground?? Or would require logic level shifter to work with Arduino...Please reply it's really urgent

[@Nematics_Lab]

I have no experience with that IC, I'm sorry

[@electronic7979]

👍

[@vamsikrishnanarayana1166]

Hai bro
How can we draw the diagram of pcb if it is more than 2layer pcb

[@screwdajuice]

you use da curry in da chickentikkamasala

[@ujjwal2206]

Intrsting

[@myshuker1978]

thanks.... but in next videos can you activate the translation language option in your video so we can understand more ......thanks again...Good luck

[@Nematics_Lab]

Alright, Which language you want?

[@ukaszs6748]

nie umiesz lutować

[@Machinecraftsman]

😅👎👎👎

[@wegi9621]

No one YT genius can't show solder from stencil over QFP 44 ? LOL QFP32 and special stencil for this? LOL I do it from hand