How to fix and diagnose issues with Samsung Ecobubble Washing Machine

Поделиться
HTML-код
  • Опубликовано: 21 сен 2024
  • Got an error message or issue with your Ecobubble. There are some REALLY simple fixes that you can check for and resolve before paying a professional. This video also shows how to put into test mode to confirm the issue.
    It will show: How to remove and clean filter, check water inlet issues, drain issues, out of balance issues and how to resolve. The test/diagnosis shown will provide a code that you can look up at Samsung (see link below) or codes below:
    1C, 1E Water level sensor issue
    3C, 3E, 3E1, 3E2, 3E3, 3E4, 3E5
    Motor issue
    4C, 4E
    Water supply issue
    4C2, 4E1, 4E2, 4Ed
    Water temperature issue
    5C, 5E
    Water drainage issue
    6E
    Water heater not functioning
    8C
    MEMS sensor issue
    8E
    Current error
    9E1, 9E2, 9H1
    Power error
    11E
    Low water level detected
    12E
    Button issues
    13E
    Signal communication error
    14E & 18E
    Button issues
    www.samsung.co...

Комментарии • 323

  • @ashleighAshlee
    @ashleighAshlee 2 года назад +12

    Thank God I found your RUclips channel! My washing machine died just now, and after doing the checks you demoed, gunk came out from the small hose next to the filter. After that my washing machine is back up and running!

    • @ratemygadgets
      @ratemygadgets  2 года назад +2

      Brilliant. Dirty job but worth it. Please do subscribe as really helps me.

    • @ashleighAshlee
      @ashleighAshlee 2 года назад

      @@ratemygadgets new sub here!!

  • @CenetRox
    @CenetRox 8 месяцев назад +2

    Washing trapped inside , unable to unlock door ,I totally forgot about cleaning the filter ... works fine again .. much appreciated !

    • @ratemygadgets
      @ratemygadgets  7 месяцев назад

      So glad, saved clothes and washing machine. Double win! Please do like the video and subscribe as it really helps me.

  • @tss8929
    @tss8929 2 года назад +5

    Thanks allot. You saved me. My washing machine suddenly stopped while washing my job clothes. Now cleaned as you said. Found five years of gunk in that. Working normally now. Will keep it clean now onwards :)

    • @ratemygadgets
      @ratemygadgets  2 года назад

      Really glad to hear. Thanks for letting me know. Please do subscribe as really helps me.

  • @mrlol3841
    @mrlol3841 2 года назад +2

    I had UC after running the test. Checked the fuse and it was knackered. Changing the fuse sorted it. Saved £400. Cheers

  • @shirleymorris482
    @shirleymorris482 2 года назад +4

    Thank you ever so much for demonstration. My washing machine was out of action for 2 months, I was about to buy new one until watching your vid. Machine now working perfectly. Thanks.

    • @ratemygadgets
      @ratemygadgets  2 года назад

      So so glad it worked for you. Saving the environment from discarding of a good machine. Please do subscribe as really helps.

    • @onyettemoreland9861
      @onyettemoreland9861 2 года назад

      Thanks so much👌🖐️😘😆

  • @DogWhispererAdeHowe
    @DogWhispererAdeHowe Год назад +2

    A good video which really helped. Our machine was stuck on 11/12 minutes in a 15 minute cycle, door locked, seemed like a call out but I watched your video and checked a few things. Firstly the wash load was a big throw that we use on the dog sofa (yes, I know they shouldn't be up there but my partner lets her 2 dogs up there, my 2 dogs don't go up there). So the load was too heavy. Plus there may have been a kink in the water feed so I made sure that was okay. Then I drained the bottom filter - yuk - and unplugged the little hose and a few drops of black water came out. It still didn't drain, seemed to gurgle a lot, so I checked the drain hose, disconnected it and made sure it was clear. Couldn't disconnect the motor hose though, too tight for my big hands. Anyway... put the machine back on, set it to rinse and spin with NOTHING in the drum and lo and behold it started working again. By the way I used the two right hand buttons to diagnose the E3 problem as in the video. So it could be more than one problem that causes the machine to stop. I just kept going through the list until it started working again. Thank you.

    • @ratemygadgets
      @ratemygadgets  Год назад

      Really glad it worked and great perserverance. The kink in the hose may have been the biggest issue. It may not drain as it can't feed the water it needs in. Either way glad could help. Please do like and subscribe as really helps me.

  • @terryfoley7725
    @terryfoley7725 2 года назад +2

    Thank you so much! Solved my E3 warning light when machine stopped working. I was delighted to see a completely clogged filter (after draining for about 10/15 minutes as you advised). Thanks again.

    • @ratemygadgets
      @ratemygadgets  2 года назад +1

      Glad could help and thanks for taking the time to write. Please do subscribe and like as really helps

    • @terryfoley7725
      @terryfoley7725 2 года назад

      Spoke too soon! Filter wasn't the problem,or at least, it wasn't the only problem. Still getting E3.

  • @jon...6825
    @jon...6825 2 года назад +3

    Thank you very much. I've learnt so much from this video. We have the same as the mother in law and hers won't spin so I found you. They won't listen to me but I've learned so much. Thanks again hope everyone has a great Christmas and God bless everyone...

    • @ratemygadgets
      @ratemygadgets  2 года назад +1

      Glad it helped and hope helps resolve the issue(s) for you. Please do subscribe as really helps.

    • @jon...6825
      @jon...6825 2 года назад

      @@ratemygadgets I've just done it, I hope you and your family have a great Christmas and God bless everyone....

  • @mellee6448
    @mellee6448 Год назад

    I couldn't get mine to go into diagnostic mode. I pressed the spin and option buttons, turned the power on and it just looked like it normally does. I turned the programme selector dial a few times and nothing happened so I stopped but it carried on going around the programme selector clock. I switched it off. Turned it back on and it carried on. I opened the door and it seemed to be waiting so I've put it on a 95c baby care wash. The issue with mine is keeps stopping part way through the washes though someone has pressed pause (although they haven't). However, I have never known before about cleaning the filter so I've done that- thank you! Really good and informative video.
    If you or anyone else can help further I'd be so grateful!

    • @mellee6448
      @mellee6448 Год назад

      It's just stopped again and been stuck at 2:12. I've had to.pause and play it again to get it to advance. This keeps happening.

    • @ratemygadgets
      @ratemygadgets  Год назад +1

      It may be (but guessing) that the pause button is sticky so keeps involuntary pressing on a cycle. It is the only thing I can think that would cause it. Get a vacuum cleaner and try to see if can suck any dust out around the button...just be careful to not be too excessive and suck the button clean off or cause more damage. Alternative is to softly blow around the button to get rid of dirt and dust. Hope helps.

    • @mellee6448
      @mellee6448 Год назад

      @@ratemygadgets thank you. Will try it.

  • @alexia6678
    @alexia6678 3 года назад +4

    Thank you, my family member forgot to take out the tissue paper and it ruined the washing machine
    Thank you for teaching me how to fix it

    • @ratemygadgets
      @ratemygadgets  2 года назад

      I am so glad. Glad i saved you money in not having to call out an engineer or worse case buy a new machine. Please do subscribe as really helps.

    • @tomgallagher9186
      @tomgallagher9186 2 года назад

      @@ratemygadgets I got a Samsung washing machine and it’s coming up with a red box what looks like a lock square box and we can’t change it to a different program because that red box is stopping it

  • @ljerromes
    @ljerromes Год назад +4

    People like you make RUclips worthwhile!

  • @Beausaint
    @Beausaint 2 года назад +1

    This is a great video! I just regret buying this washer it is the worst washer I’ve ever known. My latest problem is the extreme squeaking coming from it. 🤦🏻‍♀️

    • @ratemygadgets
      @ratemygadgets  2 года назад

      I would take the mouse out of the inner casing. If you can excuse the Dad joke, then please subscribe.

  • @veronicaconway9362
    @veronicaconway9362 Год назад +1

    thank you, were having trouble with the door not opening and programs not going. so I've set teh machine to do the test run, but there is washing in there, so we shall see, Thank you so much.

  • @mwangobree2372
    @mwangobree2372 3 года назад +3

    Thank you so much. The filter was dirty, you have saved me money!
    Thank you

    • @ratemygadgets
      @ratemygadgets  3 года назад

      I am so glad. Please do subscribe as really helps

  • @hopelesstorich3530
    @hopelesstorich3530 2 года назад +2

    Hey amazing demo, really helped me have a understanding of my machine. Wish you taught us how to do laundry though mine keeping coming out like crinkly crisps lol, and the smell of the laundry doesn't really come out on the clothes, it just smell less hahaha

    • @ratemygadgets
      @ratemygadgets  2 года назад

      Not sure I can help. Do clean out the waste pipe as may be blocking up and not draining leaving the smell. Please do like the video and subscribe as really helps me

  • @simonnattrass2171
    @simonnattrass2171 23 дня назад

    Couldn't believe how filthy and gunged up the filter was!! ❤

    • @ratemygadgets
      @ratemygadgets  21 день назад

      Good...not that it was filthy but that you found it. Once cleaned, then should sort the issue out. Please do like the video and subscribe as really helps us

  • @dianeharrison4975
    @dianeharrison4975 Год назад +1

    Ordered it’s coming in January ❤

  • @fairchan67
    @fairchan67 2 года назад +1

    Thank you. You saved my bacon. Thanks for sharing, as I just accidentally locked my dooor, wasn't aware, so pressed the two for locked, and now I am back washing.

    • @ratemygadgets
      @ratemygadgets  2 года назад

      Get in. I am literally saving time nd stress for you to enjoy your life in better ways!!! Please do like and subscribe as really helps.

  • @mel-rw5ex
    @mel-rw5ex 3 года назад +4

    i kicked mine 6 times and it worked

    • @f.g.6019
      @f.g.6019 2 года назад

      Exactly, as if I want to buy a fucking project instead of a washing machine. Useless junk

    • @mel-rw5ex
      @mel-rw5ex 2 года назад

      @@f.g.6019 it really is useless ... goodluvk with your mashing machine though

  • @MrT79shakeshake
    @MrT79shakeshake 6 месяцев назад +1

    Thanks for this I think I’ve sorted the issue with it not going into spin.

    • @ratemygadgets
      @ratemygadgets  6 месяцев назад

      Really glad. Please do like the video and subscribe as it really helps me

  • @baytree
    @baytree 2 года назад +3

    fantastic video, thank you. really well explained and demonstrated, you solved my 'dead' machine issus and saved me a ton of money on an engineer! thank you, thank you, thank you!

    • @ratemygadgets
      @ratemygadgets  2 года назад

      I am so glad and thank you for taking the time to write that. Very kind and the Internet isn't always strong on positive. Please do like the video and subscribe as really helps.

    • @baytree
      @baytree 2 года назад

      @@ratemygadgets liked and subscribed! thank you again, you are a force for good in the world

    • @euchariaukachukwu9990
      @euchariaukachukwu9990 2 года назад +1

      @@ratemygadgets Thank you for this video. In my own case, the control panel of my Samsung Eco bubble washing machine is blank even when there’s power. It didn’t stop the functioning of the dryer but I sense something is not right.

  • @nassersaleh8212
    @nassersaleh8212 2 года назад

    Thank you so much. My washing machine wasn’t work and i was trying to buy new mashing but thank you 🙏 for your help

    • @ratemygadgets
      @ratemygadgets  2 года назад

      Awesome. Just call me Money Saving boy!!!!! Please do like and subscribe as really helps me.

  • @cav3104
    @cav3104 2 года назад +2

    Exactly what I was looking for, cheers dude

    • @ratemygadgets
      @ratemygadgets  2 года назад

      Glad could help. Please do like the video and subscribe as would really help me.

  • @LynnekeChristiaensen
    @LynnekeChristiaensen 2 года назад +3

    THANK YOU SO MUCH! You are a life saver!

    • @ratemygadgets
      @ratemygadgets  2 года назад

      Saving lives and only a Tuesday! Thank you. Please do like the video and subscribe as really helps me.

  • @adelina4922
    @adelina4922 6 месяцев назад +1

    Thank you so much! I fix my problem with your video! 💯💯

    • @ratemygadgets
      @ratemygadgets  6 месяцев назад

      Glad it helped! Thanks for the nice comments. Please do like the video and subscribe as it really helps me.

  • @NicolaOBrien-e8k
    @NicolaOBrien-e8k Год назад +2

    HI, what did you do about your 3E problem? Thanks

  • @BeckysAnimals
    @BeckysAnimals 2 года назад +4

    Very helpful video! I was having a nightmare with mine but it turns out the child lock was on 🙈

    • @ratemygadgets
      @ratemygadgets  2 года назад

      Ha ha....these things happen. Please do like the video and subscribe as really helps me.

  • @Triko5
    @Triko5 5 месяцев назад +2

    Mi don’t show the test function menu she only show me 2 points and 1 line something like this :- any ideas ????

  • @yvonjones1114
    @yvonjones1114 Месяц назад

    Exactly the same with me. Thank you so much.

  • @dubtechrecords
    @dubtechrecords Год назад +1

    Great video bro fixed issue ,keep up the good work👍

    • @ratemygadgets
      @ratemygadgets  Год назад

      Cheers buddy. Great to hear. Please do like and subscribe as really helps me.

  • @davewest6316
    @davewest6316 2 года назад +2

    Ta mate, you’re a star !
    All sorted after watching your vid 👍

    • @ratemygadgets
      @ratemygadgets  2 года назад

      That is awesome. SO glad to hear. Please do subscribe as really helps me. Trying to get 2000 before Christmas.

    • @davewest6316
      @davewest6316 2 года назад

      @@ratemygadgets subbed 👍

  • @Nelstill
    @Nelstill 2 года назад +1

    Thanks for your tutorial, very useful things!

    • @ratemygadgets
      @ratemygadgets  2 года назад

      I am really glad and thanks for taking the time to let me know. Please do like and subscribe as really helps.

  • @anapaulino3904
    @anapaulino3904 Месяц назад

    How many time does take to test? My machine is testing for more than 5 minutes

  • @sajaahroseey5391
    @sajaahroseey5391 Год назад +2

    Thank you very much ❤

    • @ratemygadgets
      @ratemygadgets  Год назад

      You're welcome 😊Please do like the video and subscribe as really helps me.

  • @jineshjoyp
    @jineshjoyp 2 года назад +1

    Thanks for the Video.. It was very useful

    • @ratemygadgets
      @ratemygadgets  2 года назад

      Thank you for taking time to let me know. If you do subscribe and like it really helps me.

  • @gordonjohnston684
    @gordonjohnston684 2 года назад +1

    I had a problem with the spin, it was a Loose belt. There was a large nut in the middle of the drum that needed tightened.

    • @ratemygadgets
      @ratemygadgets  2 года назад

      Glad could help fix. Now can go back to getting the next wash ready....rock and roll!! Please do like the video and subscribe as really helps.

  • @YordleStrategist
    @YordleStrategist 3 месяца назад

    cleaning the filter did for me , thanks a lot haha

    • @ratemygadgets
      @ratemygadgets  3 месяца назад +1

      No problem 👍 Saved you lots of time and money I hope. If you could be so kind, please do like the video and subscribe as really helps me.

  • @iambeezee
    @iambeezee 2 года назад +1

    My problem is the dial is not responding. It doesn't select anything im stuck on a rinse and spin.
    Can't do a diagnostic cuz I can select/scroll through the options

  • @carolcross1209
    @carolcross1209 Год назад

    Thank you for your video. I've been working my way through the possible faults. When I push the spin, option and on buttons, the dial on the left lights up and the lights move around clockwise automatically. It doesn't let me do this manually to allow me to test. Please advise 🤔

    • @ratemygadgets
      @ratemygadgets  Год назад

      Sorry Carol. Not sure fully understand. Did you follow the guide and does it go into a test cycle? What are the issues it is showing?

  • @laufeybjorgrafnsdottir6924
    @laufeybjorgrafnsdottir6924 3 года назад +3

    Thank you. You saved my day :)

    • @ratemygadgets
      @ratemygadgets  3 года назад

      I am so glad. Really good to hear. Please do subscribe as really helps.

  • @faridahizoune6757
    @faridahizoune6757 2 года назад +1

    Hi, your video was very helpful, please my problem is that when i turn on the machin, it stops after 1 minut, and still, when i pus pause start button it work for one minute or two and stop again, i tried to get the test and kt gives me tje ( -) in the result, whats the solution please, regards

    • @Iamfromprague
      @Iamfromprague 2 года назад +1

      I have exactly samw problem, looking for a solution ass well

  • @lauradavidson577
    @lauradavidson577 4 месяца назад

    Still don't know what the symols are when i use one it just stopped for ages .

  • @benjones1452
    @benjones1452 Год назад

    Thanks so much you very lovely people

  • @GordonStewartTV
    @GordonStewartTV 6 месяцев назад

    Thanks for making this video. My 7 year old machine is dead. I have changed fuse on plug twice but still not responding and zero lights showing. I followed the press the 2 buttons and on/off switch but still nothing. Any thoughts ?

    • @ratemygadgets
      @ratemygadgets  6 месяцев назад

      If there is NO power then definitely (and stating obvious) a power supply issue. I have another video on how to change a moulded plug. Obviously only undertake if feeling confident, but you need to hope it is the plug. If not, then something will have gone in the machine OR (unlikely) the control panel display has failed. If have any.dpubt, please consult a qualified electrican or washing machine engineer. Let me know how you get on.

  • @koastdamost1
    @koastdamost1 2 года назад

    Wasn't what I was looking to fix but good to no thank you

    • @ratemygadgets
      @ratemygadgets  2 года назад +1

      Sorry didn't help but worth knowing just incase and always good to do little and often maintenance. Please do subscribe as really helps.

    • @koastdamost1
      @koastdamost1 2 года назад +1

      Helped me learn more about the machine I had a leak issue with ours found a hole at the bottom rear of the plastic tub don't no what caused it or if there was something that was supposed to be in there I just sealed it up and and ain't had a problem since

    • @ratemygadgets
      @ratemygadgets  2 года назад +1

      @@koastdamost1 Legendary. Means once less washing machine on the waste pile and saved yourself a good amount of money.

  • @deborahbarnes8377
    @deborahbarnes8377 2 года назад

    I have a Samsung ecobubble and the drive belt has come off. The reference on the belt doesn't match the actual belt measurement. Its shorter than size stated ,there also look like someone has added something to the bar that the belt goes on to stop it rolling off when it rotates which has eroded and left bits on the floor inside.

  • @nuwankumara2390
    @nuwankumara2390 2 года назад

    Thank you very much
    I fixed my machine

  • @parke48
    @parke48 5 месяцев назад

    Um excuse can you please help me my washing machine same as yours the small screen won’t work can you tell what’s the issue and can i do it by myself? No matter how many times I click on it doesn’t work or peep or anything the screen just changes when i spin the spinning thingy

    • @ratemygadgets
      @ratemygadgets  5 месяцев назад

      Is it not registering any input? So you can't get any of the buttons to work?

  • @shahzadtubeful
    @shahzadtubeful Год назад

    Hi. My washing machine is same but 8 Kg. The magnifying 🔎 consists of 2 buttons 1 option and 2 Delay End. While holding those 2 buttons I am pressing switch on button but all lights don't show meaning the machine doesn't give option to run test. Can you please help

  • @durimabazi6874
    @durimabazi6874 2 года назад +1

    Thank you so much brother

    • @ratemygadgets
      @ratemygadgets  2 года назад

      No worries. Please do like and subscribe as really helps me.

  • @Acouzic
    @Acouzic 2 года назад

    Hello and thanks for your videos ! Have you an idea of how much time it takes for the test operation ? 🙏

    • @ratemygadgets
      @ratemygadgets  2 года назад

      No entirely. Mine took roughly 5mins. Hope helps. Please do ike the video and subscribe as really helps me

    • @shaunmcgee4204
      @shaunmcgee4204 11 месяцев назад

      @@ratemygadgetsI followed your instructions for the diagnostic test and the machine was still going over two hours later. Initially, the problem was 5C and water wasn’t draining.

  • @kevinjohn725
    @kevinjohn725 2 года назад +1

    I had a similar problem with my Samsung it got down to 9 minutes and then just kept going round slowly I think it was over loaded I checked filter as you advised but still the same so I stopped it and took out one of the small blankets out and left the other one in and it span
    Hope this might help someone .Great video
    Regards kev...

    • @ratemygadgets
      @ratemygadgets  2 года назад

      Thanks for advice. Does sound like it was overloaded. Please do subscribe as really helps.

  • @VIP.UC1
    @VIP.UC1 Год назад

    Thank you so much I am sort it out the problem

  • @AJ-tp5qj
    @AJ-tp5qj 5 месяцев назад

    Hi i have the same washing machine the issue am facing is that the buttons on the dash stopped working ecept the on/off play buttons so i can actually use the washing machine but cant adjust ant of the cycles (spin , water temp..) any pointers would be highly appreciated
    Note: Child lock is not on :)

    • @ratemygadgets
      @ratemygadgets  5 месяцев назад

      Is the display still working? If so, then do try (but not likely to work) unplug from the wall(Obviously when empty and not mid load). Give it a few mins and plug back in. It mayhave got itself in a weird cycle loop OR the buttons are not working? Hope helps, please do like the video and subscribe.

    • @AJ-tp5qj
      @AJ-tp5qj 5 месяцев назад

      @@ratemygadgets screen works cycles work its just the buttons are not responding ,unplugged it before still didnt work ! The buttons simply stopped working

  • @matthewhicklin1507
    @matthewhicklin1507 Год назад

    hi there , do you have any videos how to correct a D3 error code , possible door lock
    thanks

  • @suryakandukuri3439
    @suryakandukuri3439 2 года назад

    it worked for me. Thanks for the video

    • @ratemygadgets
      @ratemygadgets  2 года назад

      So glad. Thanks for letting me know. Please do subscribe as really helps me.

  • @noufb9353
    @noufb9353 2 года назад

    Thank you, could you help me to fix the screen. I want do test but the screen not working nothing appear in it !!!! I dont know whats the wrong with the screen.

  • @michellegorman2512
    @michellegorman2512 2 года назад

    Hi.... have you got any videos showing how to change a door latch/locking system on the ecobubble?

  • @JOJo-jv2vb
    @JOJo-jv2vb 2 года назад

    My dial is broken I put a new one in but still turns around in air I done realised it has a metal clip at the back that came off I cannot select washers for Spin Cycles do you know how I can fix it the first happens when I went to clean behind it and pulled it off it was working fine after 6-months is started to turn around selecting replacing the not I realised that a small metal ring loose hanging on the metal bar where you were replace the knob but it does not seem to clip onto anything

  • @zannahmartell9813
    @zannahmartell9813 3 года назад +65

    Dont ever ever buy this machine

    • @aaronmorling2671
      @aaronmorling2671 3 года назад +5

      Iv had mine four years and no problem until now so why not

    • @f.g.6019
      @f.g.6019 2 года назад

      @@aaronmorling2671 well, because it's shit. What sort of bloody Einstein do you have to be to get your fucking clothes clean FFS

    • @luketheminer7732
      @luketheminer7732 2 года назад +9

      8 years ours lasted and has been hammered with kids clothes n bedding fucking unbelievable machine if u ask me and cheaper in electricity

    • @ianferguson3455
      @ianferguson3455 2 года назад +1

      We’ve had ours 9 years. Had early issue with faulty circuit board causing failure of drum to rotate half way through programme. Samsung replaced free as was under 5 years parts guarantee. No problems after that. Fault was poor soldering on the circuit board. No problems since.

    • @gordonjohnston684
      @gordonjohnston684 2 года назад

      I understand why, the very minor issue’s I had were very easily sorted out with the help of Utube.

  • @ruffneck718
    @ruffneck718 2 года назад +1

    Thank you sir.

    • @ratemygadgets
      @ratemygadgets  2 года назад

      SIR! I feel honoured. Please do subscribe as really helps.

  • @xSheepz
    @xSheepz 6 месяцев назад

    Mate thank you, awesome vid ❤❤❤

    • @ratemygadgets
      @ratemygadgets  6 месяцев назад

      No problem 👍 Thanks for the kind words. Please do like the video and subscribe as really helps me.

  • @margiesedillo7771
    @margiesedillo7771 5 месяцев назад

    Hello ..how can unlocked the washing machine please? Thanks

  • @swiatwolanas
    @swiatwolanas 2 года назад +1

    When you do diagnost test need to be connect to water suppplier?

    • @ratemygadgets
      @ratemygadgets  2 года назад +1

      Not 100% sure as only done when water is on. It doesn't pull in any water so guess would be it isn't essential. Hope helps. Let us know. Please do subscribe as really helps.

  • @titoahmed7852
    @titoahmed7852 Год назад

    Great video. i have the same machine, but the buttons are not working. What can i do

    • @ratemygadgets
      @ratemygadgets  Год назад

      Do you have anything on the display? If so, then an interface issue with it being all buttons so sounds like a connector come loose.

  • @carlos.galhano
    @carlos.galhano 3 года назад +2

    And if The machine does not switch on. My machine sometimes doesn't power on, and no turn on any ligts

    • @mohammadaskari7487
      @mohammadaskari7487 2 года назад

      Same issue here. Were you able to get it working?

    • @carlos.galhano
      @carlos.galhano 2 года назад

      @@mohammadaskari7487 Yes, there was a problem on the electronic chip. We replace it with 90€ for a new one.

  • @nishelchauhan3360
    @nishelchauhan3360 6 месяцев назад

    I’m wondering if you can help. I have the same washing machine but when you hit the on button it’s not coming on. Any advise on this?

    • @ratemygadgets
      @ratemygadgets  6 месяцев назад

      It could be the fuse in the plug, please see a professional electrician if needed.Please do like the video and subscribe as it really helps me.

  • @ken2k33
    @ken2k33 Год назад

    Hello, I have a samsung ww90k5410ux washing machine. It gives me a 5C code. Had it for about 5+ years already. I tried to unscrew the filter pump cap but only the cap comes off. The filter remains inside so I have no clue of how to take the filter inside out. I feel the cap should be attached to the filter but seems it isnt.

    • @ratemygadgets
      @ratemygadgets  Год назад

      I would guess then that the filter is stuck in place as gunged up (that is a word I think). Can you see into the filter to see if it is clogged? If so, it might be hard work and careful don't damage it but pulling out the debris with fingers may mean can eventually pull the whole unit out. Hope helps. Please do like the video and subscribe as really helps.

  • @sanelizabethsan392
    @sanelizabethsan392 3 года назад +1

    Thank you 👍

  • @beautybaracace1232
    @beautybaracace1232 2 года назад +1

    Thanks it worked

    • @ratemygadgets
      @ratemygadgets  2 года назад

      Great. Glad could help. Please do like the video and subscribe as really helps.

  • @js8971
    @js8971 2 года назад

    Mine seems to be very sensitive to how level it is.. the smallest of increments make or breaks weather it decides to spin.
    Also- couldn't get mine to go into diagnostics mode. // ah well... meeh- it's working now.. until the next time.....

    • @Leo-gt1bx
      @Leo-gt1bx 8 месяцев назад

      Same problem did you find a solution?

  • @michaelreddington9145
    @michaelreddington9145 6 месяцев назад

    Hi there, I've got just a red key symbol on my EcoBubble display and it won't finish a cycle. Any ideas what this could point to?

    • @ratemygadgets
      @ratemygadgets  6 месяцев назад

      I would guess, but no promise, it hasn't drained fully. It means it has finished the cycle but will not unlock until it senses the drum has drained. Check if there is water in there. If so, put it on drain mode and watch it. If it doesn't go down, you have your answer. Either a blocked drain pipe (check filter and pipe) or worse, a failed drain pump. Any doubt seek advice from a qualified washing machine engineer. Let us know how you get on.

  • @hottrayxxx
    @hottrayxxx Год назад

    Hi. I have the WW90TA046X. It makes an awful squeaky noise when washing and when spinning, a loud tapping noise. Iv been in touch with samsung many times and iv tried what theyvhave suggested...i practically brand new, have for less than 2 months. Just did drain and spin on one towel (maybe 8pcm x 30cm), it made the loudest tapping noise. Why? Any help appreciated. Thanks

    • @ratemygadgets
      @ratemygadgets  Год назад

      Is it tapping as if something is in the drum? It may be that you've had a zip or coin find its way in between drum and outer housing.

  • @Azov23
    @Azov23 8 месяцев назад +1

    I'm going to try it ive had my Samsung ecobubble a month I still can't get it on.😢

    • @ratemygadgets
      @ratemygadgets  8 месяцев назад

      Best of luck. Let us know how you get on. Please do like the video and subscribe as it really helps me.

  • @mehmetsesen9046
    @mehmetsesen9046 2 года назад

    Does anyone know the drain hose size please? Our one is cracked and need to buy a replacement, but I can't seem to find out which one to get.

  • @eddyzahu
    @eddyzahu 2 года назад

    hello there, can u help me pls, where does the drain pipe goes? i cant figure it out, i don't c a hole or something like that to put the pipe in or plug in it... THX, its a model WD146UVHJSM

  • @abojanaemad6642
    @abojanaemad6642 3 года назад

    Hello, thank you for all your helping, I have question, I have samsung 8k, when I make test mood, give error, 3c2, what is this mean 🌹

  • @jimjamsco4970
    @jimjamsco4970 Год назад

    Hi
    Maybe a bit late, but does your filter door not just press in to open instead of trying to pry it open?

    • @ratemygadgets
      @ratemygadgets  Год назад

      Some do, the design is slight different on the differing models. Mine you need to pry open. Thanks for watching, please do like and subscribe as really helps me.

  • @calvinsherren
    @calvinsherren 2 года назад

    Got donated one today, washes fine but the buttons on the control panel don’t respond in any way. Only power and start/pause. Any advice on what it could be? Thanks!

  • @scriptedknowledge3145
    @scriptedknowledge3145 2 года назад

    Explain what is the 3e1 or 3e2 then. I have the same

  • @NoviceDIYerNoel
    @NoviceDIYerNoel 2 года назад

    Hi there. We have a samsung front load washing machine, and we noticed it takes longer than usual to wash. One time I noticed, when the timer was down to 7 minutes of washing, it changed to 16 minutes. What seems to be the problem? Thanks in advance

    • @ratemygadgets
      @ratemygadgets  2 года назад

      Depends. It could be a genuine problem if it happens during the cycle and is the same issue I had. If it happens before a new washing starts then not an issue. Let me explain. Let's go with the bigger issue.....if part way through a cycle (so well into the wash) and then the time displayed doesn't reduce or increases then something at that point in the cycle has gone wrong. Either it hasn't been able to drain provided heat, spin etc so it keeps trying. If near the end then likely a draining or high spin issue so keeps adding time to resolve the issue which if it doesn't means you have along term issue. If the cycle finishes eventually then may be intermittent. Now for lesser issue and to be expected. If display provided shows let's say 30mins before you start the cycle and then on hitting go it increases, this could be expected. The washing machine will weigh the load on start and if heavier than expected then it increases the time for washing as needs more time to add water, spin, drain etc. Hope helps. Please do subscribe as really helps me.

  • @beverleypryor371
    @beverleypryor371 2 года назад

    Any chance you could advise me please? My Samsung ecobubble machine is not taking the fabric softener, I've done all the cleans but notice if I put my finger in the drain away hole it's clogged. Can you tell me if that is indeed just a hole or an actual pipe as I don't want to push gunk further down and block it further down? Also how can I access it to clean as it's very fiddly. The two screws on the front I think are just for the fascia panel? Any ideas please?

    • @ratemygadgets
      @ratemygadgets  2 года назад

      If end of drain pipe then should be clear. Get end of a screw driver and plug anything out of there. Do a drain cycle. Please do like and subscribe as really helps me.

    • @beverleypryor371
      @beverleypryor371 2 года назад

      @@ratemygadgets still nothing is clearing it :(

    • @ratemygadgets
      @ratemygadgets  2 года назад

      @@beverleypryor371 is waste water coming out and was it the waste pipe blocked (the grey hose coming put the back)?

  • @a.t.g000
    @a.t.g000 2 года назад +1

    My washing machine keeps turning off even tho I’ve replaced the mother board what’s going on?!?!?

  • @spiced32
    @spiced32 Год назад

    My drum just virtually came off, was rattling for a week. Surprise surprise had it 6 years, but a 5 year guarantee

    • @ratemygadgets
      @ratemygadgets  Год назад +1

      You wonder if they've designed it in that way. Seriously though, you may be able to fixing. If the belt has come off then easy enough or the bolt holding the drum may need reconnecting. If you unplug and remove the back, you'll be able to see. Please do like the video and subscribe as really helps me.

    • @spiced32
      @spiced32 Год назад

      @@ratemygadgets I've already ordered another washing machine m8, I think its well and truly had it unfortunately 😔

  • @Vlorche
    @Vlorche 2 года назад

    My machine comes up with DC error I have to open and close the door 3 times and then it locks and works any tips?

  • @michaelpemberton7047
    @michaelpemberton7047 6 месяцев назад

    GOAT

    • @ratemygadgets
      @ratemygadgets  6 месяцев назад

      Damn....I mean Damn! Thanks man. That is huge. Please do like the video and subscribe as really helps me.

  • @niveafairman
    @niveafairman 2 года назад

    Hi my machine is not turning on after I believe I overloaded it. It didn't spin. And now it doesn't turn on at all. We've called an engineer to diagnose the issue and reckons it is the border. He warned it will will over £ 130 to buy a new part plus labour on the top of the £70 he charged to diagnose it. I don't think it is worth the price although the machine is only 2yrs old..

    • @ratemygadgets
      @ratemygadgets  2 года назад

      If lights are not coming on,check plug fuse. If it is coming on then check the belt hasn't come off. Can you freely rotate the drum? If so, then no blockage BUt belt may have come off as should feel resistant to turn by hand. Please do like and subscribe.

  • @johnmpainter1041
    @johnmpainter1041 Год назад +1

    Love how the kid went yeahhh

    • @ratemygadgets
      @ratemygadgets  Год назад +1

      Better than when they moan (which happens a lot). Please do like and subscribe as really helps me.

  • @sergioantuna
    @sergioantuna Год назад

    Hello. I have the same washing machine... but it is impossible for me in test mode... what would be the correct way?? thank you

    • @ratemygadgets
      @ratemygadgets  Год назад

      Is it not going into test mode at all.

    • @Leo-gt1bx
      @Leo-gt1bx 8 месяцев назад

      ​@@ratemygadgetsMine is also not

  • @Insp.CountMortisWinshipKlaw
    @Insp.CountMortisWinshipKlaw Год назад

    The door won't open on mine. I've turned it off and on and still it won't open. Checked filter and no issue there

  • @dianeharrison4975
    @dianeharrison4975 Год назад +1

    I love it 🎉

    • @ratemygadgets
      @ratemygadgets  Год назад

      Good. Hope it worked for you? Please do like the video and subscribe as really helps me.

  • @adamdines444
    @adamdines444 2 года назад

    Do you know if you can reprogram the temperatures permanently to save energy?

    • @ratemygadgets
      @ratemygadgets  2 года назад

      No. Don't think you can as set by machine. Please do like and subscribe as really helps me.

  • @justchilling830
    @justchilling830 3 года назад

    Tnku so much.. 🎉❤️

  • @zinhlemsali4048
    @zinhlemsali4048 15 дней назад

    My machine doesn't have the options button

  • @luketheminer7732
    @luketheminer7732 2 года назад +1

    Hi does anyone have any ideas on why my washing machine won't start it powers on but then stops won't turn theres no error code and iv cleaned the filters could a drainage pipe be blocked?

  • @mattdale1605
    @mattdale1605 2 года назад

    Hi There,
    Any idea for if the emergency bypass cable accidentally drops back inside the machine?

    • @ratemygadgets
      @ratemygadgets  2 года назад

      When you say bypass cable, do you mean electrical cable or water/waste cable?

  • @normanblack2359
    @normanblack2359 2 года назад

    Hi can you help me please.
    Knob on eco bubble 8kg doesn't select. Call the knob out and a washer came out with it bought a new knob but it still doesn't select do I have to change the whole panel

    • @ratemygadgets
      @ratemygadgets  2 года назад

      Not sure. If the knob had just been turning and not moving the spindle then maybe not. It may be a new knob would fix it. I think you need an engineer.

    • @normanblack2359
      @normanblack2359 2 года назад

      @@ratemygadgets no knob just turns without selecting.. I would send pic but don't know how

    • @normanblack2359
      @normanblack2359 2 года назад

      So I guess I need to change the front panel if the knob that attaches to the inside broken off it had a silver washer. Would changing panel work?
      I will never buy Samsung washing machine again.
      Stick to old school hotpoint my one lasted 18 yrs

  • @Leo-gt1bx
    @Leo-gt1bx 8 месяцев назад

    Mine is not spinning. The machine won't go into service mode any suggestions?

  • @KieranAG
    @KieranAG Год назад

    Mine is only displaying UC while in Service Mode only. How do i fix it? Mine isn't the inverter model. It is fine on normal wash programmes.

    • @ratemygadgets
      @ratemygadgets  Год назад

      What issues are you having? Is it not spinning, draining, rinsing?

    • @KieranAG
      @KieranAG Год назад

      @@ratemygadgets It works perfectly fine in normal washes etc. As soon as i enter service mode it says UC :(

  • @steveh2432
    @steveh2432 Год назад

    Why does my Samsung WD90K5B10 not have an emergency bypass tube? I only have the option to pull the tube out and the water goes everywhere!

    • @ratemygadgets
      @ratemygadgets  Год назад

      Is annoying.. can you get a bucket under there?

    • @steveh2432
      @steveh2432 Год назад

      @@ratemygadgets Not under 5mm of space