Thank you so so much. This is a really great video. Can you make one more video to explain the meaning of the circuit brand arrows? Hot Neutral Ground. I have difficulties on understanding it.
So great video. We normally run armored cable from outlets and then gather them to a box close or on the ceiling, and then we run 3/4 emt and keep it as more wire as possible but wont exceed 12. Can you take off EMT and wires by this way? And it looks in your way place 3 wires in 1 emt seems waste lots of space, is'nt it?
Thai is awesome ! I have a question : when we at our company run branch, we do it with a scale master and clicker. Everytime we go over a fixture, we hit the clicker , how can I run branch on bluebeam and have it count the fixtures I'm branching together at the same time ? I can't find anything like that?
For branch you can only do the polylengths. If you need the counts for the total branch there is a parenthesis beside it. If you want I do one on one training. Go visit my website at www.triple7electrical.com
I created my length assemblies in the tool chest under branch wiring, but by mistake, I added 10’ on the rise and drop section. Is there a way to remove the 10’ on all my branch wiring assemblies all at once or individually without having to create the assemblies again? Thank you and hopefully someone can help out with this
Interesting, but I guess Bluebeam is not the ideal tool to perform this manual work. Why not use the counting in AutoCAD or any other Software in which these power layouts were created. It is much faster for the Designer to perform and extract MTO's in it while preparing the layout than doing in later on on the pdf's
![Quando Rondo - Life Goes On [Official Music Video]](http://i.ytimg.com/vi/eIf3fhMXAow/mqdefault.jpg)
Thank you for this tutorial, the Properties Mode was what I was missing.
Very nice guide. Clear Audio, Video and spokening dollar. Thanks for this.
This helps so much thank you for taking the time to do this.
You're welcome!
Thank you so so much. This is a really great video. Can you make one more video to explain the meaning of the circuit brand arrows? Hot Neutral Ground. I have difficulties on understanding it.
Thank you. very helpful
How do you account for the counts in between when you are doing multiple outlets in the same run to cover the points of connection inn between boxes?
So great video. We normally run armored cable from outlets and then gather them to a box close or on the ceiling, and then we run 3/4 emt and keep it as more wire as possible but wont exceed 12. Can you take off EMT and wires by this way? And it looks in your way place 3 wires in 1 emt seems waste lots of space, is'nt it?
Thank you!
Thai is awesome ! I have a question : when we at our company run branch, we do it with a scale master and clicker. Everytime we go over a fixture, we hit the clicker , how can I run branch on bluebeam and have it count the fixtures I'm branching together at the same time ? I can't find anything like that?
For branch you can only do the polylengths. If you need the counts for the total branch there is a parenthesis beside it. If you want I do one on one training. Go visit my website at www.triple7electrical.com
How do you get blue beam to just show your tool chest that your working not your whole list of tools
I created my length assemblies in the tool chest under branch wiring, but by mistake, I added 10’ on the rise and drop section. Is there a way to remove the 10’ on all my branch wiring assemblies all at once or individually without having to create the assemblies again? Thank you and hopefully someone can help out with this
yes, you can just duplicate the assembly and adjust the rise/drop factor in the measurements tool
Can you to all this in a tablet
Why not just search for the symbol in the legend and revu make the count automatically? I mean this is still a somewhat labour intensive task
REVU doesn't always pick up all symbols via the rectangle.
What version of bluebeam is this?
2020 Version
Interesting, but I guess Bluebeam is not the ideal tool to perform this manual work. Why not use the counting in AutoCAD or any other Software in which these power layouts were created. It is much faster for the Designer to perform and extract MTO's in it while preparing the layout than doing in later on on the pdf's
how can get contact you?
You can call me on my cell (661) 593-9252
UM, UM..............................................................................
Hello Friend will you consider doing a video taking-off conduits 🙏🙏🙏🙏🙏🙏🙏💪🏻💪🏻🫵🏻