Yamaha Drive G29 Golf Cart - Body Removal
HTML-код
- Опубликовано: 11 фев 2025
- This video goes over how to remove the front and rear body from a Yamaha G29 Drive golf cart. This body removal procedure will be the same for all the 2007-2016 Yamaha Drive G29 YDR golf carts. Be sure to subscribe to follow along with this awesome build series where we will be installing a Predator 22 hp 670cc engine in this 2007 Yamaha Drive gas golf cart. It will also be getting a Madjax 6" a-arm style lift kit, custom painted body, and a bunch of other goodies along the way!
G29 Predator 670 Build Playlist - • Yamaha G29 Predator 67...
If you got some good value from this video, please consider supporting our channel here - www.paypal.com...
Check out our Yamaha Drive/Drive 2 accessories here - powerequipment...
Body clip removal tool - amzn.to/3EuXokN
PB Blaster to remove push pins easier - amzn.to/352sEZB
Camera/Mic setup - amzn.to/3yD3u0X
By using the affiliate links listed above for Amazon or Ebay, I may earn a small commission from your purchase at NO additional cost to you. Your support from using these links helps our channel so I can continue to bring you more content!
#yamahagolfcart #yamahadrive2 #yamahag29 #yamahagolfcar #bestgolfcar #golfcartlife
Very informative and down to earth instructions thank you
Thanks for watching!
Hey Jonas, thanks for this extremely informative video. Do you happen to have a video on how to safely pressure wash the engine compartment also, do you know the location of the switch to put it in neutral
I believe I have just purchased the same or similar used model. Thanks!
No, we don't have a video about washing. There really isn't much you can hurt. Just use common sense and you should be fine.
To put the cart in neutral, just move the f/w lever to half way between forward and reverse. You should feel the cart roll easily when you get it in the correct position.
Thanks for watching!
@@PowerEquipmentMan thank you so much! 😊
Very Nice! Looking forward to this build. Thank You
Thanks for watching
Excellent tutorial, thank you
Thanks for watching!
Thank you for this 🙏🏻 I just picked up a 2013 G29 gas.
Thanks for watching
Great video! Just curious what you guys use to brighten/clean the black trim.
We use SC1 - ruclips.net/video/zQ3HmXNtFNo/видео.html
How long roughly it takes to remove a body from a golf cart?
Depends on how good you are! For a G29, I would guess around an hour.
Will the Predator engine start/ stop like the stock engine or does it stay running when you take your foot off the gas?
It is possible to use the starter generator from your stock engine to run the Predator engine, but it takes some pretty good fab skills to make everything to do it. There aren't any widely available kits that I know of to do it. Otherwise, it would just start with the key and stay running all the time.
If you need to replace the push pins- what size should they be?
These carts use at least 4 or 5 different sizes of push pins. Unfortunately, most of them are pretty difficult to find except directly from Yamaha. You can use parts diagrams to find part numbers for the ones you need.
www.bigskygolfcars.com/oemparts/c/yamaha_golf_car/parts
Would a drive 2 body fit on a G29 drive ?
No. They are quite a bit different.
Like sample 150 or any cc
357cc
fantastic
Thanks for watching!
Any idea if the yamaha adventurer two utility with dump has the same size frame as this cart? Was looking to buy one and convert it into a 4 seater. Thanks
Sorry I don't have much info on that. I believe the back of the frame is quite a bit different to support the bed. The frame is also longer than a normal cart. I'm sure it is doable if you are willing to fabricate your own rear seat kit. You most likely wont be able to buy anything that will just bolt on.
How much Cc engine
How much was the upgrades priced out
A lot! Lets just say you could have bought a brand new cart for what we had in this one.