OMG! Thanks so much! It worked a little different for me but it still worked. After requesting the config file and opening it, I only had to change the part where it says: "Manufacture programming mode *Unlocked to --> *Lock. And after making this change following the rest of your video.
Very helpful tutorial. As an HP elitebook user that recently replaced a motherboard, this tutorial made a difference. Never found a reason to use the free HP Bios utility until today. It is always available for download in the HP driver page. The other tutorial are confusing. I guess in this case, thank you for staying with HP available tools
the details u entered like sr no. Where to get them from? Also this manufacture programming mode came after a fix by technician now should it remove this or not
Hey bro! I got my air vent fan replaced yesterday and this message "Manufacture mode is unlocked" showing on screen and its starting like regularly after that and device information is already there I checked.... Any idea is this a problem and how to fix this?
@@Laptop_repair_zone setting status=fail Name=system board ct number Reason= access denied....after doing this command prompt showing this....wt to do now
1 character in the BID was tough to read, looked like an I but when magnified could be an f as it looks like a crossbar, may try again with capital i, a lower case L, or the lower case F and see it if accepts the data, the lacking of the mode was the issue.. likely a virus hit the unit, using the HP utility they once released for entering that mode. I used to be HP field tech not sure if IDs work maybe some software available online under my tech ID,,, hate to use when not on a ticket though...
I rebooted, entered BIOS exited and saved and now it boots up without stating in that mode even though appeared toggled when checked.. had some error about 3 of the entries on 1st boot, but they were gone after subsequent boots.. not sure what that was about,, may try again with FB but the all Fs for windows is likely issue why will not authenticate..
Hi. My HP zbook 17 G6 notebook show: warning system is not fully configured, please contact HP support. How can i remove that warning with BCU. Help me.
Sir mera laptop dell ka h our mera laptop on nhi ho rha sir please help me sir manufacturing mode level 85 Press fn x To return the system to Normal running video sir ye problem aa rhi h please sir btaiye kaise thik kru
@@Laptop_repair_zone As I said, when I execute "/setconfig:config.txt" the cmd returns me "changeStatus="fail" reason="Access denied" " in the most fields.
in my laptop i take this error when i writing location to the cmd "'C:\Program' is not recognized as an internal or external command, operable program or batch file. how can i solve? thank you
6 times saw your video canot go to your link ...it shows your account is deactivated ..please help i need to remove manufacturing programe error from my laptop
dont know why they dont have app like that inside the bios like with few models on i work. just get to bios and fill info. this looks worse than DMIfit
![[Solve] Product Information not Valid HP Laptop | HP Manufacturing Programming Mode Is In Unlock](/img/1.gif)
OMG! Thanks so much! It worked a little different for me but it still worked. After requesting the config file and opening it, I only had to change the part where it says: "Manufacture programming mode *Unlocked to --> *Lock. And after making this change following the rest of your video.
Did access denied error happened before changing to unlock?
Thanks so much. Had to do this to an entire fleet. Now I remember this process very well.
Ethan Chow thanks for your comment, please share my videos.
Very helpful tutorial. As an HP elitebook user that recently replaced a motherboard, this tutorial made a difference. Never found a reason to use the free HP Bios utility until today. It is always available for download in the HP driver page. The other tutorial are confusing. I guess in this case, thank you for staying with HP available tools
Is your replaced motherboard still working? I am worried as I spent the amount and replaced the motherboard.
Helpful, after bios programming. Thank you.
Thank you a lot for your visdom!
For months been trying to get rid of 00a, watched so many videos that was Useless.
the details u entered like sr no. Where to get them from?
Also this manufacture programming mode came after a fix by technician now should it remove this or not
I can't find all the product informations. Is there any way to get them. I already tried hp support assistant and hp partsurfer
Hi I have a probook 650 g1 that asks me for various information: what is it and where can I find product SKU where can I find CT umber. Thanks
Nice work. 👍 Many thanks.💲
Are build id and feature byte same for all pc
Hey bro!
I got my air vent fan replaced yesterday and this message "Manufacture mode is unlocked" showing on screen and its starting like regularly after that and device information is already there I checked.... Any idea is this a problem and how to fix this?
Thank you so mutch..greate vedio..thanks a lot..❤❤❤❤❤
Thanks for your comment.
thank you man!, You're a genius
Thanks for your comment, please share my videos.
Great worked for me thanks❤
Can you help me as I got the message as you want to do repot or if no confirm make shutdown but after I did the both I got same problem
Great Video it is working
the ct number you use,
is it for the new board or old board
Thanks for your comment. old board
great job...👍
Thanks for your comment, please share my video to social account...
Hi, I only get 16 fields and the model number, serial number etc are not part of them. Can you tell me what I'm doing wrong? Thanks
Same happening to me
thank you man! worked for me
Thanks for your comment, please share my videos.
I Love you thanks!!!!!
Very helpful, thanks for the video
Thanks for your comment.please share my video.
Thank You❤❤❤❤❤❤
You are so welcome
my laptop shows system board (00a) - system board ct number....is the same procedure applicable
thanks for your comment, yes.
@@Laptop_repair_zone setting status=fail
Name=system board ct number
Reason= access denied....after doing this command prompt showing this....wt to do now
Try another version please.
bro how did u sort it out? i've ran into the same problem&idk what to do now to make it disappear
entries are read only up top, more than in your log, can we remove that in edited version? also, is there no sound in video?
that was up above.. below I entered data, it accepted all but the BID and locking programming mode
1 character in the BID was tough to read, looked like an I but when magnified could be an f as it looks like a crossbar, may try again with capital i, a lower case L, or the lower case F and see it if accepts the data, the lacking of the mode was the issue.. likely a virus hit the unit, using the HP utility they once released for entering that mode. I used to be HP field tech not sure if IDs work maybe some software available online under my tech ID,,, hate to use when not on a ticket though...
I rebooted, entered BIOS exited and saved and now it boots up without stating in that mode even though appeared toggled when checked.. had some error about 3 of the entries on 1st boot, but they were gone after subsequent boots.. not sure what that was about,, may try again with FB but the all Fs for windows is likely issue why will not authenticate..
is there any problem if i don't fix this error? (HP ELİTEPAD)
Thank you for the information but what's about 32 bit operation system.
Thanks for your comment, same process run 32bit exe .
Hi. My HP zbook 17 G6 notebook show: warning system is not fully configured, please contact HP support. How can i remove that warning with BCU. Help me.
Excelente muy buen video gracias
I have different problem, my laptop has all information saved correctly, but i get a message "Machine is not in committed state" please help
thanks for your comment,you need AMTOOL please search in google.
when i do in cmd promote is showing ERROR msg="System not supported. Unable to connect to HP WMI namespace:'root\HP'" my laptop is g6 please help
thanks for your comment, please try with HP DMI TOOL.
Hi bro, was the problem solved?
does this work also for hp elitebook 2170p?
Thanks for your comment,yes.
@@Laptop_repair_zone thanks for the answer.
Sir mera laptop dell ka h our mera laptop on nhi ho rha sir please help me sir manufacturing mode level 85
Press fn x To return the system to Normal running video sir ye problem aa rhi h please sir btaiye kaise thik kru
It's very easy to fix. Just press FN and X key at a same time on your laptop keyboard when you see the message on your laptop screen. Thanks.
salamwoalikom brother ihave the same problem in hp probook 650 g1 but idont find Build id...why
thanks for your comment,walaikum salam, it should be under RAM slot, if you don't find than you can take it from another laptop thanks.
I did as done in the video but it is saying that it can't read the file, what should I do now??
Thenks sir
Always welcome dear. Keep supporting and sharing our videos.
cool video except you didnt have link for the utility is annoying trying to find it
You are the man!!!! Thanks!!!!
Thanks man ❤
You're welcome 😊
Everything was perfect and no error but when we restarted it changes does not happen and it showing the same error . Plz help
Thanks for your comment, try with other version.
Access denied error
Ran cmd as administrator still this error occurs
how do i find out about the feature byte, built id number and sku number ?
Alex Kang thanks for your comment, check under RAM slot and laptop back cover .
Thanks
What is Product Family?
Thanks so much
thanks for your comment.
I get a red error message system not supported. Any idea??
Thanks for your comment, please try another version.
Hi bro, was the problem solved?
How do I activate the HP laptop UEFI factory programming mode?
bro it is not running with 64bit.exe and with 32 bit.exe showing not recognized and without 32 or 64 bit .exe it is showing error
, plz help man
Please this site for download has been blocked by hp since April 2022.. please can you help post the file for Hp pro book 11 x360 ..
Bro when I press enter it shows me "Access denied
" in the most of the options, please help me :c
I have a HP Pavilion x360
Nicolas Herrera sorry?
@@Laptop_repair_zone As I said, when I execute "/setconfig:config.txt" the cmd returns me "changeStatus="fail" reason="Access denied" " in the most fields.
Try to another version of BCU
@@nicolas9915 replace VSS section to empty in bios with hexeditor.. then retry
@@LeadFarmer813 I am the same situation, all the modifies is returning with access denied .
I tried the exact same steps on my hp laptop 15af103ax, it says access denied! Can someone help me please?
Ejecutar como Administrador!!! Saludos
bro. I need to reenter system family option after the mobo got replaced. Any idea how to find this?
Thanks for your comment.
in my laptop i take this error when i writing location to the cmd "'C:\Program' is not recognized as an internal or external command,
operable program or batch file. how can i solve? thank you
You have to write cd before the command
thank u
hi, config.txt not creat :( , files sp107705.exe there is only this files . Help me pls
sir ye error kyu aata hai plz tell me
6 times saw your video canot go to your link ...it shows your account is deactivated ..please help i need to remove manufacturing programe error from my laptop
Which link ?
Please send me your wtsup number
How do i unlock mpm because it says access denied
Is this safe to do? I am afraid i might brick my laptop
Yes it's safe
Hii hp laptop is not opening what should I do it is showing same as yours its not going forward
Thanks for your comment,
in my hp envy 15 i cant find model no or any serial no option in the text file
Sajjad Ali thanks for your comment. try with other version.
I did this but it only found 12 settings. not 24.....Did not help
Thanks for your comment, please try with another version.
I'm getting bcu update failed because of serial number. I'm putting in the serial number on the back the laptop
Thanks for your comment
@@Laptop_repair_zone ok no help at all
Hello there I can't paste biosconfiutilty 64 any help please
Crtl C to copy
Crtl V to paste
Try it
Not working for me in hp 248 G1....
Thanks for your comment.please try other version
dont know why they dont have app like that inside the bios like with few models on i work. just get to bios and fill info. this looks worse than DMIfit
Not working