LOL... I just saw this video and was laughing my butt off! You always set the high end first to a good high and solid scream and then set the low end just to get a good throttle response. NEVER set the idle with the low or high needle. Unscrew that idle needle with the spring on it and throw it over your shoulder. Then adjust the idle with your radio which closes the butterfly valve till you reach the idle RPM that you want.
This engine has now been adjusted to rotate rotated at about 2000-8000 a 16 × 8. Glow and gas prices in the engine, fuel economy, a noticeable difference in fuel costs, gas engines are now freely enjoy the environment. 2-stroke, the more variations of the four-stroke aircraft fly, the engine is adjusted, use the cub 1 / 5.
To breakin the engine you have to continiously go high-low, high-low, high-low for a couple of hours in order let the piston ring to sit on the sleeve. If you go only low throttle the pressure inside of cylinder is not enough to push the piston ring to the sleeve wall. You will not breakin engine with only low throttle even if you run the engine for 1000 hours. It is not going to happen. You have to go high and then low cycle ...mean time not to allow engine heat up because it is new and parts are not work together and friction can damage parts. The guy in video is doing right . It is exactly what needs to be done.
Excellent engine ! Dial it in on the test stand , and just let it run. A couple hours of stand mounted break in and you have a real nice engine that gets better by the minute. Lots of snot for such a small engine!!⭐⭐⭐⭐⭐
Hmm, looks like a good engine... looking at one of these for my H9 Blue Nose P-51.... cheap, looks good.... how are you liking it? Got it in a plane yet???
Breaking my DLE20 with a 17x6 and I cant seem to getting over 7500 RPM. it seems to be running great but research shows 8500-9000 RPM with this setup. I've only burned about 1/2 gallon so far and hoping ill get more RPM as it breaks in. Anyone have any thoughts on this? What RPM's where you getting during break it? Thanks, John
Можно спросить! Двигатель будет работать без аккумулятора или нет. На али экспрессе из точно такого же двигателя выходит провод. Зачем он там, если по нему не идёт электричество от генератора к зажиганию? Заранее спасибо. (Хочу купить такой, вот и спрашиваю)🇷🇺
32:1 all day with regular oil...Don't use that synthetic or synthetic blend crap...Unless you wanna buy a new motor when you mistakenly lean it out...Also, as you can see...He's in and out on the Throttles...Don't let the motor sit there full blast for Break In... I think the book says 3-4000 rpm's....Also, as you can see....Always use a Tach...This ain't Glow or Nitro...Your ears can't detect a 1000 or more RPM's change...And that's the difference between running well or overlean...and a new motor to be bought coz you just burnt up the one you got....Cheers 🍻!!!!
Where can I purchase an engine already broken in ready to fly!!?? Apparently no one where I fly knows how to tune or breake in engines,,I bought 2 and they just fucked them up for me!! I need one that it's ready to just put on a airplane,,by the way I fly at Balboa airport in San Fernando valley,,no one know how!!!!
+xxxxmrwinoxxxx you will have to tune it either way weather conditions will effect it no matter what it could have been tuned perfectly for a week and next time run like crap this is something your gonna have to learn on your own
+xxxxmrwinoxxxx TRY REDWING RC!!! IVE GOTTEN MANY ENGINES FROM THEM PRE-RUNNED/BROKEN IN AND HAD NO ISSUES!! THEY ONLY CHARGE ABOUT $50 BUCKS TO DO IT!!!!
@@mukhdi80 read the Directions that come with the engine. FOLLOW TO EVERY WORD and you will have a good reliable engine. DO IT WITHOUT ANYBODY THERE BUT YOU. Input from others can really fk up the whole deal.
Save your breath there mate! These dudes dont even speak english lol. And besides, he adjusted it correctly by the end of the video. He did it the way the instructions say to do it
LOL... I just saw this video and was laughing my butt off! You always set the high end first to a good high and solid scream and then set the low end just to get a good throttle response. NEVER set the idle with the low or high needle. Unscrew that idle needle with the spring on it and throw it over your shoulder. Then adjust the idle with your radio which closes the butterfly valve till you reach the idle RPM that you want.
This small engine looks so powerful. Love it 👍
This engine has now been adjusted to rotate rotated at about 2000-8000 a 16 × 8. Glow and gas prices in the engine, fuel economy, a noticeable difference in fuel costs, gas engines are now freely enjoy the environment. 2-stroke, the more variations of the four-stroke aircraft fly, the engine is adjusted, use the cub 1 / 5.
Great presentation
Can you reverse helix. rotation to install the engine in the tail to push forward?
This video should be titled "How Not To Tune An Engine"
Every time he picks up the screwdriver I cringe lol
Yes I agree with you a cringe worthy video!
To breakin the engine you have to continiously go high-low, high-low, high-low for a couple of hours in order let the piston ring to sit on the sleeve. If you go only low throttle the pressure inside of cylinder is not enough to push the piston ring to the sleeve wall. You will not breakin engine with only low throttle even if you run the engine for 1000 hours. It is not going to happen. You have to go high and then low cycle ...mean time not to allow engine heat up because it is new and parts are not work together and friction can damage parts. The guy in video is doing right . It is exactly what needs to be done.
Try mounting the tank at the same height as the crank of the engine. It will run even better.
Excellent engine ! Dial it in on the test stand , and just let it run. A couple hours of stand mounted break in and you have a real nice engine that gets better by the minute.
Lots of snot for such a small engine!!⭐⭐⭐⭐⭐
Hmm, looks like a good engine... looking at one of these for my H9 Blue Nose P-51.... cheap, looks good.... how are you liking it? Got it in a plane yet???
Qual lbateria vc usa para alimentar o cdi amigo
Can i use in a ground vehicle?
Breaking my DLE20 with a 17x6 and I cant seem to getting over 7500 RPM. it seems to be running great but research shows 8500-9000 RPM with this setup. I've only burned about 1/2 gallon so far and hoping ill get more RPM as it breaks in. Anyone have any thoughts on this? What RPM's where you getting during break it? Thanks, John
Have you solved the problem
@pcm501es Not bad.. Mine with 16x8 Beech Wood 1700-9050rpm
What electric starter are you using to turn the prop? Thanks.
Sullivan is good, but for this a hangar 9 , tower hobbies , Hobbico branded starter is just fine.
Можно спросить! Двигатель будет работать без аккумулятора или нет. На али экспрессе из точно такого же двигателя выходит провод. Зачем он там, если по нему не идёт электричество от генератора к зажиганию? Заранее спасибо. (Хочу купить такой, вот и спрашиваю)🇷🇺
Now you can start easily by hand.
Do you tell me that how to wire ignition system to simply start engine
Please look here.
manuals.hobbico.com/dle/dleg0020-manual.pdf
What is the best gas/oil ratio for a run in dle?
32:1 all day with regular oil...Don't use that synthetic or synthetic blend crap...Unless you wanna buy a new motor when you mistakenly lean it out...Also, as you can see...He's in and out on the Throttles...Don't let the motor sit there full blast for Break In... I think the book says 3-4000 rpm's....Also, as you can see....Always use a Tach...This ain't Glow or Nitro...Your ears can't detect a 1000 or more RPM's change...And that's the difference between running well or overlean...and a new motor to be bought coz you just burnt up the one you got....Cheers 🍻!!!!
hi lads just got mine not yet run
Acho errado dar partida no motor logo em alta rotaçao.
Adjusting RPM idle with the H feul screw?
No wonder it runs like shit.
next time. put the Engine up a Bit higher. so Air can Blow over the Cooling Fins.
Well Ya See. the Engine is Air Cooled. the more it has Moving Over it. the Better.. its a Simple Thing. @@Nitroglowr
are you like breaking in this engine? ouch
And hi-torque started will do the trick
Where can I purchase an engine already broken in ready to fly!!?? Apparently no one where I fly knows how to tune or breake in engines,,I bought 2 and they just fucked them up for me!! I need one that it's ready to just put on a airplane,,by the way I fly at Balboa airport in San Fernando valley,,no one know how!!!!
+xxxxmrwinoxxxx you will have to tune it either way weather conditions will effect it no matter what it could have been tuned perfectly for a week and next time run like crap this is something your gonna have to learn on your own
+xxxxmrwinoxxxx TRY REDWING RC!!! IVE GOTTEN MANY ENGINES FROM THEM PRE-RUNNED/BROKEN IN AND HAD NO ISSUES!! THEY ONLY CHARGE ABOUT $50 BUCKS TO DO IT!!!!
@@Oooa1227 Please share the link of proper carb tune, i also want to know how to do it
@@mukhdi80 read the Directions that come with the engine. FOLLOW TO EVERY WORD and you will have a good reliable engine. DO IT WITHOUT ANYBODY THERE BUT YOU. Input from others can really fk up the whole deal.
Save your breath there mate! These dudes dont even speak english lol. And besides, he adjusted it correctly by the end of the video. He did it the way the instructions say to do it
mate i tell you gas beats electric
longer runtimes plus gas engines give you all the power
same with electrics but less runtime ahhahahhaha
dios mio fue mierda