I have one of those cheap little welders. Don't use an extension cord if at all possible when welding with it. I know from experience that you want to be as close to an outlet as possible with the shortest cord you can. When I had mine on a 20' cord all it did was splatter and lay boogers. I plugged it right into the outlet and got great penetration and decent stacked welds
I have seen them plate what is cut out and put a temporary pipe. Then cut the rest of the front out and weld in a 3” pipe to the plates. Then remove the temporary pipe. So the 3” pipe is close to center. I have to say,you have your self a hot rod!! I use to put a pack of cigarettes on the dashboard and leave the back window unlatched,and the pack of cigarettes would be where I started, lol. Non believers had to sit in the back seat and try to hold on to the front seats,hahahahahaha! I would flip them and land the cigarettes where I started,hahaha!! I’m excited for you brother,this dog will hunt!
I've got 2.8 frame mounts in mine and they bolted right in no problems you can put the nuts on the back side and everything I've got zinc bolts bolting my 2.8 mounts in I didn't have to cut anything and I had a full size 1500 huge starter on my S10 Blazer I did have to cut the tip off of my drive shaft when I first start the stock drive shaft back in but I'm running a 700 r4 transmission
I wish you could send some of that rain to the northwest end of the state. Y’all always getting good rains and we get a couple tenths, barely settles the dust.
A transdapt crossmember is cheap . With a th350 stock one will work if you have one laying around one from a s10 truck will also work. Don’t understand why even for a big block swap you don’t need to cut the truck up , I didn’t and I had BB two turbos and two radiators all in engine bay
I have that same engine I posted about it being a ATK 383 engine and she will run fine on 93 brother just letting you know that because I have that same engine same heads everything and mine is 5yrs old still running with nitrious
Go to harbor freight they have a titanium flux 125 welder there for less than $200 bucks I guarantee you it'll be the best welder you buy for you it runs off 110 and welds hot
Careful pouring gas down the carb with it running. One backfire through the carb and you are basically holding on to a grenade. Not trying to be the safety police...just dont want to see you lose any fingers 😂
Well I didnt wanna be one of those people asking strangers for money lol.. but it's a RJT601 I guess if yall wanna help the cause.. I'm trying to get a few odds n ends to get the blazer finished up now
![Ice On My Teeth - ATEEZ エイティーズ 에이티즈 [Music Bank] | KBS WORLD TV 241115](http://i.ytimg.com/vi/c-n92OgbbwA/mqdefault.jpg)
Yall follow me on Facebook if you'd like! BowtieGuy601
Followed. This is the stuff I love to see. Rural ohio here.
I have been following your channel for years and Im so impressed with your patience.... Great videos
I love watching yall work on chevys I have 84 c10 and I learn a lot from watching you . Keep on turning wrenches my brother
I have one of those cheap little welders. Don't use an extension cord if at all possible when welding with it. I know from experience that you want to be as close to an outlet as possible with the shortest cord you can. When I had mine on a 20' cord all it did was splatter and lay boogers. I plugged it right into the outlet and got great penetration and decent stacked welds
I have seen them plate what is cut out and put a temporary pipe. Then cut the rest of the front out and weld in a 3” pipe to the plates. Then remove the temporary pipe. So the 3” pipe is close to center. I have to say,you have your self a hot rod!! I use to put a pack of cigarettes on the dashboard and leave the back window unlatched,and the pack of cigarettes would be where I started, lol. Non believers had to sit in the back seat and try to hold on to the front seats,hahahahahaha! I would flip them and land the cigarettes where I started,hahaha!! I’m excited for you brother,this dog will hunt!
Late to the party. That was a struggle, but sounds awesome. Thanks for taking us along for the ride
This thing gonna eat!!! She sound healthy !! Real healthy !
Nice! She sounds strong 💪🤠
I've got 2.8 frame mounts in mine and they bolted right in no problems you can put the nuts on the back side and everything I've got zinc bolts bolting my 2.8 mounts in I didn't have to cut anything and I had a full size 1500 huge starter on my S10 Blazer I did have to cut the tip off of my drive shaft when I first start the stock drive shaft back in but I'm running a 700 r4 transmission
I had a 12:1 383 in a 87 blazer..it was brutall fast on motor.. went well into the 10's!
I do believe that’s gonna be one quick little blazer
I wish you could send some of that rain to the northwest end of the state. Y’all always getting good rains and we get a couple tenths, barely settles the dust.
Looks good bud keep up the good work. Hope you get 100.000 this year
I wonder if the welder works better when it gets low because the roll of wire gets easier to turn and the wire feed speed gets faster 🤔
Maybe
Man i really like that orange and black obs
Higher motor mounts what is it the but sitting down lower and back further will help with weight distribution
Looks like its gonna be a blast
I would love to work on my stuff at night but then again I don't want my neighbors to think I'm a tweaker 😂
Channel should be called SHADE TREE MECHANIC lol
This gone be good
Could be fun bud thanks for your videos
i wanna see that 383 in your c10 once its blown up that 383 looks to be a solid little motor
Wee that motor sounds 💪 I'd put it in 80 model just saying good video keep 💯
motor sounds solid
OSHA approved my brother lol
A transdapt crossmember is cheap . With a th350 stock one will work if you have one laying around one from a s10 truck will also work. Don’t understand why even for a big block swap you don’t need to cut the truck up , I didn’t and I had BB two turbos and two radiators all in engine bay
Yeah im not sure man I didn't see it with the big block
I have that same engine I posted about it being a ATK 383 engine and she will run fine on 93 brother just letting you know that because I have that same engine same heads everything and mine is 5yrs old still running with nitrious
Go to harbor freight they have a titanium flux 125 welder there for less than $200 bucks I guarantee you it'll be the best welder you buy for you it runs off 110 and welds hot
Wait 2.8 mounts will work on short block swap?
I was talking about the factory 2.8 frame mounts
@@bowtieguy601 yes. Will work for a small block on a s10?
Put antifreeze in that one lol
Awesome😎🥃🇨🇦
It looked like it didn’t have an oil filter on it
It didn't at first but I put one on it before I started it
👍
What ole hot wheels been up too
He's trying to get his rat rod on boost
He needs some injectors
Careful pouring gas down the carb with it running. One backfire through the carb and you are basically holding on to a grenade. Not trying to be the safety police...just dont want to see you lose any fingers 😂
Lol yeah not my first rodeo
What a pile
Yo mama
Need to put your cash app in your about page
I was thinking the same thing I'd send a few dollars so he can get parts and tools lol
@@edwardblaine8426 yup
Well I didnt wanna be one of those people asking strangers for money lol.. but it's a RJT601 I guess if yall wanna help the cause.. I'm trying to get a few odds n ends to get the blazer finished up now
I’ve been saying the same thing bro ! Atleast for some gas ⛽️ wouldn’t hurt lol
I call bullshit on the 13.1 compression and it being a 383 stroker, sounds like a bone stock 350 with headers,
Well thats what it is so 🤷
Said it pumps 250 psi on cranking