If you want the best fishing tips, spots, and strategies, plus exclusive discounts on fishing gear you’re probably already buying, click here to join us in the Insider Club: bit.ly/3Fcjj1L
Hey Luke. Great instructional video! I thought of an easier way to cut the 1 3/4” holes. Instead of buying two 1x3s, buy an extra 1x6, draw a line lengthwise down the center, mark and drill the holes where you want them, then cut the 1x6 down the line and you have your two 1x3s. Worked for me.
I built one of these a couple years ago, it’s not the best. I’m probably going to build one more like this, because if I give my rack any type of movement half the rods fall. Worked great in a garage closet but no in my bedroom haha
Felt strips glued into half circles (especialy the uppers) would soften the contact point. Posted that half way through before Luke mentioned it. I like his take on it.
I wasn't able to download the pattern for your rod holder. Would you be able to email it to me please or send me a link to be able to do so. Thank You in advance and I appreciate you doing this for people like myself
I would love to know the angle for the base. Spacing etc. But I would like to say that if you have a table saw this could be a bit easier. instead of 1x3 gat a 1x6 cut your holes and then rip it in half. Either way job well done sir.
dont have the tools for something like this. what I did was buy a 50pack of this little plastic grommets and screwed a couple into the stud in the wall. fishing poles clip right in to them.
Agreed! Should've just drilled holes on a 6in(5.5) first then ripped 1/16th off center(easier to eye the edge of the saw blade)...First time I ripped was with a circular saw; before I purchased a table saw. He even said he had a circular saw. Lol...Also, cedar pickets are cheaper and look fancier.
If you want the best fishing tips, spots, and strategies, plus exclusive discounts on fishing gear you’re probably already buying, click here to join us in the Insider Club: bit.ly/3Fcjj1L
A hint is to use blue painters tape to wrap around the boards between each hole to help hold them to gather while you’re drilling. Great looking rack.
Great tip!
Hey Luke. Great instructional video! I thought of an easier way to cut the 1 3/4” holes. Instead of buying two 1x3s, buy an extra 1x6, draw a line lengthwise down the center, mark and drill the holes where you want them, then cut the 1x6 down the line and you have your two 1x3s. Worked for me.
Thx from the Netherlands!!!! B&B Fishing will be launched quick.. i will send you a photo of our rack!!
Glad we could help!
Thanks! Love the video and all the details. I’m going to try making one this winter!
Thanks so much!
Nice DIY rod rack
That wuz awesome. Im definitely gonna make one
Thanks! Hope you have fun making your rod rack.
Now this is somewhat what I would love to see more of.
Glad to see that you enjoyed this video
Great job Luke !!!
Thanks Pablo!
great project !...like the simplicity of the rod rack
Cool video man. Just stumbles across your channel now. Something nice you can make in an afternoon and of course great storage for your prize rods ✌😁👍
We're glad that you found the video helpful! 💪 We appreciate the support!
Good job man!
Thanks!
How do find find the paper to Print
Thanks I have made my diyrod rackthanks to your channel
How cool! So glad to see that you made a rod rack.
I built one of these a couple years ago, it’s not the best. I’m probably going to build one more like this, because if I give my rack any type of movement half the rods fall. Worked great in a garage closet but no in my bedroom haha
Great job!!! I should try this 🧐🤓
Felt strips glued into half circles (especialy the uppers) would soften the contact point. Posted that half way through before Luke mentioned it. I like his take on it.
Thanks for making time to post the helpful comment!
Where did you find the felt?
Nicely done been looking to make a custom rod holder
Thanks!
Use a 1x6. Drill holes the. Rip board in half. Much easier.
Good advice thanks!
Hey Luke. I’ve been wanting to make that exact rack. Where can I find the PDF that you mentioned?
The PDF is linked in the main article for this video on our website... here's a link: www.saltstrong.com/articles/diy-rod-rack/
Good joh
nice 👍
Thanks for watching!
Put one of those little 2 hole metal plates on the end , screw it on each end and the boards won't move
Can I use a 2” hole or does that matter?
Not bad I like it.
Thanks!
I wasn't able to download the pattern for your rod holder. Would you be able to email it to me please or send me a link to be able to do so. Thank You in advance and I appreciate you doing this for people like myself
I can't print the PDF, what are the measurements on the holes. It would help if you added the measurements on the PDF
I would love to know the angle for the base. Spacing etc. But I would like to say that if you have a table saw this could be a bit easier. instead of 1x3 gat a 1x6 cut your holes and then rip it in half.
Either way job well done sir.
Nice!! Where’s the template? Thank you, I have so many rods I need organization lol
The PDF hole guide template is linked in the main article for this video on our website... here's a link: www.saltstrong.com/articles/diy-rod-rack/
Where is the template located?
The PDF template is linked in the main article for this video on our website... here's a link: www.saltstrong.com/articles/diy-rod-rack/
Needed some clamps
Could be added!
wouldn't it had been easier to use a 1x6 drill the holes and then rip it down the middle on a table saw? nice rod rack though
Yes... I just don't have a table saw so this was the low-cost route.
@@Saltstrong thankfully I do. I think I am going to build 2 or 3 of these. Thanks for the great video and wonderful idea.
You could stain it or paint some fishes on the wood.
It's excellent
U stole my idea
Is it bad to store my rods in a shed?
We recommend storing rods in temperature controlled environments to maximize their lifespan (especially if you live near saltwater).
dont have the tools for something like this. what I did was buy a 50pack of this little plastic grommets and screwed a couple into the stud in the wall. fishing poles clip right in to them.
Cool idea!
There's no template attached to your instructions.
The PDF hole guide template is linked in the main article for this video on our website... here's a link: www.saltstrong.com/articles/diy-rod-rack/
Didn’t see a pdf file?
The pdf file is available in our private insider community on the same fishing tips video post at www.saltstrong.com 💪
Looks like you need to build another 10 racks!
Haha!
C clamps
Poor carpentry skills 😂
Agreed! Should've just drilled holes on a 6in(5.5) first then ripped 1/16th off center(easier to eye the edge of the saw blade)...First time I ripped was with a circular saw; before I purchased a table saw. He even said he had a circular saw. Lol...Also, cedar pickets are cheaper and look fancier.
𝓢𝓱𝓾𝓽 𝓾𝓹
Appreciate the comment and you watching!