The information is mostly the same from video to video. The main changes are when unifier releases a new version of the software which then changes out the options. Something like this could be broken down into sections and then you could just have to update one or two sections out of an entire build.
As a IT-support person, who never really got elbow deep in networking, this is great! Going out tomorrow to config a AP on a clients guest network for the first time, so this was a nice quick rundown :) Thanks!
Thank you for the vid! I had to do a reset on my UDMP and had lost all the settings and such (didn’t have any current backups) seeing this in its new UI helps track it back to speed again. Thanks!
Great video, greatly appreciate the detail and how comprehensive it was. Answered a bunch of questions for me about how UnifiOS works! Thanks for the information.
Excellent tutorial and overview. One question: can you please go over LAN-In, LAN-Out, LAN-Local? It seems like a simple concept, but I haven't found a definitive explanation yet.
Fantastic overview and setup. While I've used many of your previous videos as guides, I'll switch to this comprehensive updated version as my go to! Thanks!
Thanks for a bunch of great suggestions! I'm a bit confused about the Default network, though. All UniFi infrastructure goes there while home automation, printers, Sonos and so on goes into IoT. Would it make sense for a home user to put personal computers, servers and possibly smart phones in a network corresponding to Staff (setting up FW rules for access to e.g. printers) or should they go into the Default network as well? What's the intended purpose of the Default network? And also, while creating the Guest WiFi network you input a password (WPA Personal enabled) and then the Guest Hotspot is enabled. What are best practices here, how would the guest reach the Guest Hotspot landing page with a password protected WiFi? Is it considered safe to leave that network Open without password given the "Guest Network" type with Client Device Isolation enabled?
Thank you so much for sharing great stuffs. Very helpful. I am looking for a vdo how to set up a FOM / backup UDM pro as my original one got burn by lightning.
@@MactelecomNetworks I have a question, im gettin the SE, 2 unify 6 pro and 2 cams, its just for my place, that would cover wify and cable, but is something else woth the investment now that i may need in the future?
Thanks a lot for this great tutorial. You talked about IPv4, can you give us more information about a typical IPv6 setup? From my point of view, IPv6 adds some new problems, eg a working DNS system is required because remembering IPv6 adresses is not so easy ;-)
Thank you for your videos. They’ve been a tremendous help in configuring my network. I run ndi streams over a separate vlan from my primary network to improve ndi stability. So far so good there. I’ve added the firewall rules like you’ve suggested including the one to give the ndi vlan access to my bad on my primary network and it works great with one exception. One of the workstations on the ndi vlan is connected to my UniFi aggregation switch via 10gig connection and since moving that workstation to this ndi vlan it is speed limited to what seems like 1gig speeds to the nas which is also 10 gig to the same unifi aggregation switch. How can I overcome this speed limitation? Is layer 3 switching needed?
Great video, thanks. I have your network structure implemented on my UDM Pro SE running protect. I fail in connecting to Protect with a iOS device connected locally to any other network than default/LAN. Do you know how to fix this, or the rule to configure to allow Protect iOS app to reach the Protect controller in the right way?
Finally did it from start to finish I would say about 90% of this is still valid there are some screens different with the recent updates but I was able to get it done. Still have a lot of questions but thank you for such an excellent video buddy!
I have a UDMPRO with a 1GB lease line connected to a U6LR in my bookstore. I tried every setting under the book but they were getting 5-30mbs Wi-Fi download speeds. I then got a cheap router and they were all getting 800+. I replaced the U6LR yet same result. Did an RF scan all full. I don’t know I’m just not sold on them.
Thank you for the video, I followed it and setup my network the same way. However, I have my wifi printer in the IOT network and and I can't print from devices on my other ssids like my 6ghz network. Is there a firewall rule I can add?
Could you do a video on setting firewall rules to allow a Sonos APP to work when inner VLAN blocking is configured? the device is on the user network Sonos is on the iOT network Thanks!
These videos are super helpful, It would be awesome if you could do a bit more of an in-depth video of the devices that should be connected to each network. I am still at little confused as to what network we should be connecting all our computers and phones too, IoT or the default. Or how our smart devices talk to our phones if were on seperate networks?
Computers would be on a “trusted network” cell phones really are IoT devices. But ya I should make another video explaining it better also different firewall rules :)
as always a great video. Question : what are the shortcomings (if any) if the IoT network is created as a guest network? and will this eliminate the need for manual firewall rules + port and IP Groups?
i had a issue doing my IoT as a guest... partly because if you enable the guest network and landing page for WiFi, it kept trying to make guests go to the IoT network. I ended up doing my IoT and Guest networks as their own corporate networks and created the firewall rules then i didn't have issues with my WiFi guest network...
I've been watching your videos for eons. I had a bad UDM Pro on a job that we replaced and imported the settings of the previous device (it would be accesible for 30ish minutes before crashing and was stuck on a very old version of software (around 3 years ago). Anyways, while I'm watching this and I completely understand what you are teaching...I have my cameras at this location set on a different vlan. Remote access to the cameras worked previously to this new device going in with all of its software updates. I am not sure how to set the appropriate rules in order to open up the NVR's port which is on the same vlan as the cameras themselves or if I am just wrong in that older setup and should move the camera nvr to the native network and create rules allowing cameras to communicate with it...which seems like it'd be a ton of extra work.
Watching this video, it seems to me that the Unifi Equipment is very simple to setup. I'm tempted to maybe give this stuff a try, I work in the Telecommunications Industry, ans I am only used to working on our equipment that we have.
I honestly like your videos, so much information and helpful for someone new. But I have to replay the videos 20x for each step because you move/talk so fast. Slow it down a little bit :)
Can you utilize the UDM PRO SE as the core/distro with Flex Minis switches hanging off of that? So ports 1-8 on the SE can we use them as uplinks going to the flex’s?
Hi. My question: How can i setup the countree on one-clict VPN? I would like use TIktok with other regio. Next question: I have UDM PRO plus IPS 2x1GB i setuped two WAN. But i would like mixing the speed to 2GB i cant. I use CAT 7 do you have suggest, or i need change to UDM SE?
I appreciate the videos. Between you and crosstalk i just pre-setup my unifi stuff the other night (don't have it in use yet). If it's not too much to ask could you (or crosstalk, not that he'd see this comment) do a how-to to take a port from a switch and pass it through a docker on unraid to use its vpn. This way i can take a program on my pc and bind it to a port on the pc then plug that port into this switch port which would then vpn just that program and not have to install the vpn software (nord) that has already messed up my pc a couple times and was a chore to undo. Ive been debating trying to tue into an opnsense vm i stead of the udm for firewall. Also maybe a "quickie video" on best practices of what items to put under what networks, pcs, smartphones, camers, servers/nas (unraid/truenas), network printers, etc.
Im a little green to switches.. does it make sense to put degices in seperate vlans if your not making firewall rules to block and allow traffic between them?
Curious - Should I still be able to ping from a default connection over to an IP device on my Vlan when connected locally to my UDM pro? I don't have wifi access for my UDM Pro at the moment.
Hey Cody, I have a question: I have a Camera network set up on VLAN 30 and a corresponding WiFi network created for my G4 Instant cameras. However, when I adopt the Wifi cameras, they are adopted into my default network however, I am never able to migrate them to any VLAN network in Protect. Have you seen anything like this in the past and if so what's the fix? (Ps. I am able to connect other devices to the camera wifi network without incident.)
For a noob. I use a Unifi USG Security Gateway with an non managed switch (Netgear). With 1 LAN and 2 VLANs (IoT and Guest) is it possible for my cabled IoT devices like Philips Hue be placed on a VLAN (IoT) or do you have to have a managed switch and adress specific ports on the switch for a VLAN?
Would I create Firewall rules for VoIP just like IoT rules? The only firewall full I see that is default id the one created by UniFi called "Allow UniFi Talk Traffic" under "Internet Local". Since it is created by UniFi, I cannot see what is in this rule or how it is defined.
Great video! Can you or have you created a video that goes over failover to LTE and to only funnel VOIP traffic and limits the bandwidth until WAN is restored?
i am a firm believer all vlan ports should be in the same interface processors on the switch (concurrent interface port#).. keep them together for easy troubleshooting...
Does any of this change with the 3.x.x update? I am using the UDMP and we just got the 2.x.x and almost 3.x.x updates. I used your guide back in 2021with the 1.x.x firmware and the old UI, don't know if I need to redo it with new features.
Does this allow for default group to initiate connection with device on IOT and allow response but block iot device from initiating connection to default vlan?
In the section about creating networks you have your "third octet" set to 30 for your cameras. I'm attempting to follow along but it says it must be a valid IP etc etc. What's going on with that?
If we're going to be using unifi cameras (all wired), would there be a reason to have a separate virtual network for cameras? I can understand segregating third party cameras and NVR to another virtual network, but what would the reasoning be in this case? Just trying to learn more about proper procedures - thanks again for all the knowledge you share!
If you have Wifi cameras (G3 Instant, etc) would you also create a Camera Wifi and assign it to the Camera network? Also, can Wifi IoT devices just go on the Guest network since they just need internet access? Is there a reason to have them separated?
I have a WiFi network that is attached to my Camera network and have all of my WiFi cameras on that specific (hidden, obviously) SSID. This way, all of your WiFi cameras are automatically assigned to the Camera network.
Great video! I followed all of your same process of creating the Profile for the Port and IP Groups for the RFC1918, then created all of the Firewall rules for our internal networks to be able to talk to the other vlans, but none of them can still ping the others... thoughts/suggestions?
In addition to the rule going from internal network to other vlans, I also made a "LAN IN" rule going the other way, from the vlan back to internal network. Then I started being able to ping as Cody was in the video with his NAS. Cheers, ev
Love your videos and all the info, but as a person in the IT field where our company uses Ubiquiti products, how on earth do you find availability? Is there an actual place where you can speak to a Ubiquiti rep, because we've tried everything to find a contact and an actual distributer that has stock of their products. Any advice or help would be amazing (cause it seems like a lot of youtubers, including people like Linus TechTips, have zero issues getting all of their products with ease) Thanks and please keep the content coming!
Due to China being locked down until Jan 23. Hope they can get going again soon. I have been buying from eBay to fulfill clients orders. Paying over the top for gear but keeps the client !!
When blocking ports 80, 443, 22 access to gateways, why do you exclude the source VLAN gateway from the destination group (you say "we don't want to put our IoT gateway in this group" at 17:33)? That requires you to create one destination IPV4 group for each source network (each excluding respective source networks' gateway, which is why you named the GW group "Block IoT to gateways" instead of just "All gateways" i suppose). I tested to include all gateways in my lab network, and everything works fine (except for GW web access, which the VLAN users should not have anyway). This will reduce the number of IPV4 gateway groups from many to 1. Or have I misunderstood anything?
Here is one for you . All seems well on local site and i can block and manage traffic between vlans etc., but with site to site VPN it doesn't matter what rule I put in place noting seems to block traffic between sites. I have two sites and i want management site to have full access to client site, but client site to have no access to management site
Any particular reason to get a NVR is you already have a Dream Machine Pro? Since the DMP can run unify protect seems like a waste to buy the NVR. Am I missing something?
When assigning a VLAN to a specific port on my UDR, I get "An error has occurred while saving port configuration".. In fact, it says that no matter what I do.. I cant configure ports on my UDR and save it. I get that message... Pretty frustrating..
Hey. I probably wont make a video on that but you just need to login to the bell modem then there is a section called port forwarding. There you just put the IP of your UDM Pro or SE
I have a dream machine pro and I have had to factory reset that 3 times now and the APs around my network because of firmware updates. I have no idea how people rate their products because I have had a nightmare with them. Nothing worse than being away and everything has gone down, and you just can't connect to do anything.
Constantly updating the "complete setup" videos is a great ideas. I would suggest once every 6 months
The information is mostly the same from video to video. The main changes are when unifier releases a new version of the software which then changes out the options. Something like this could be broken down into sections and then you could just have to update one or two sections out of an entire build.
I agree but the interface changes quiet a bit. Probably do full build videos once a year with update videos afterwards
As a IT-support person, who never really got elbow deep in networking, this is great! Going out tomorrow to config a AP on a clients guest network for the first time, so this was a nice quick rundown :) Thanks!
This information is super valuable! Thank you for taking the time to make this and elaborate on some of it concepts mentioned!
Thank you for the vid! I had to do a reset on my UDMP and had lost all the settings and such (didn’t have any current backups) seeing this in its new UI helps track it back to speed again. Thanks!
Great video for someone like me about to purchase this equipment for my new home. Thank you!
Just got an SE and can't wait to get started with the config. Thanks so much for this video.
Great video, greatly appreciate the detail and how comprehensive it was. Answered a bunch of questions for me about how UnifiOS works! Thanks for the information.
Excellent tutorial and overview. One question: can you please go over LAN-In, LAN-Out, LAN-Local? It seems like a simple concept, but I haven't found a definitive explanation yet.
Just excelent timing as I have my UDM SE for about 4 days
Thank you for posting a great video of the complete setup tutorial using the new UI.
Great info! Was looking for this type introduction to the Unify landscape. Not working with it yet but may be soon.
Awesome video. Learned a lot. Thank you for posting it!
I love this! Can't wait for the 2023 version
Great video thanks for taking the time to make this video, This will be my go to video 😃👍
Thank you so much bro. Smashed it bro
Awesome! Excellent video!
As always awesome and very informative video. Good work
Fantastic overview and setup. While I've used many of your previous videos as guides, I'll switch to this comprehensive updated version as my go to! Thanks!
It’s a few new things just in longer format. When new firmware comes out I’ll just do new update videos
You sir, are awesome.
You are the best.
Thanks for a bunch of great suggestions!
I'm a bit confused about the Default network, though. All UniFi infrastructure goes there while home automation, printers, Sonos and so on goes into IoT. Would it make sense for a home user to put personal computers, servers and possibly smart phones in a network corresponding to Staff (setting up FW rules for access to e.g. printers) or should they go into the Default network as well? What's the intended purpose of the Default network?
And also, while creating the Guest WiFi network you input a password (WPA Personal enabled) and then the Guest Hotspot is enabled. What are best practices here, how would the guest reach the Guest Hotspot landing page with a password protected WiFi? Is it considered safe to leave that network Open without password given the "Guest Network" type with Client Device Isolation enabled?
Thank you so much for sharing great stuffs. Very helpful. I am looking for a vdo how to set up a FOM / backup UDM pro as my original one got burn by lightning.
Appreciate the video, thank you! I run into issues connecting Sonos to my IoT. Any directions there?
Love the updated video. Is there any chance you can go through how to properly set up a printer to print from one vlan to another?
just in time, im about to order my stuff so this is helping a lottt
Awesome let me know how it goes
@@MactelecomNetworks I have a question, im gettin the SE, 2 unify 6 pro and 2 cams, its just for my place, that would cover wify and cable, but is something else woth the investment now that i may need in the future?
Hoping the 2023 version comes with the right switches! ❤❤❤❤
Thanks a lot for this great tutorial. You talked about IPv4, can you give us more information about a typical IPv6 setup? From my point of view, IPv6 adds some new problems, eg a working DNS system is required because remembering IPv6 adresses is not so easy ;-)
Thank you for your videos. They’ve been a tremendous help in configuring my network. I run ndi streams over a separate vlan from my primary network to improve ndi stability. So far so good there. I’ve added the firewall rules like you’ve suggested including the one to give the ndi vlan access to my bad on my primary network and it works great with one exception. One of the workstations on the ndi vlan is connected to my UniFi aggregation switch via 10gig connection and since moving that workstation to this ndi vlan it is speed limited to what seems like 1gig speeds to the nas which is also 10 gig to the same unifi aggregation switch. How can I overcome this speed limitation? Is layer 3 switching needed?
Very cool tutorial, thanks!
Thanks for watching
Great video, thanks. I have your network structure implemented on my UDM Pro SE running protect. I fail in connecting to Protect with a iOS device connected locally to any other network than default/LAN. Do you know how to fix this, or the rule to configure to allow Protect iOS app to reach the Protect controller in the right way?
Are you able to do something similar for Corporate environments? Highly appreciated..thank you
Finally did it from start to finish I would say about 90% of this is still valid there are some screens different with the recent updates but I was able to get it done. Still have a lot of questions but thank you for such an excellent video buddy!
Well you're in luck I will be making another 2023 full network setup with the new interface
@@MactelecomNetworks that’s why you the man dawg
@@MactelecomNetworks Soon Please :D
excellent, thank you
Question: is multi WAN IPs s working now?
I have a UDMPRO with a 1GB lease line connected to a U6LR in my bookstore. I tried every setting under the book but they were getting 5-30mbs Wi-Fi download speeds. I then got a cheap router and they were all getting 800+. I replaced the U6LR yet same result. Did an RF scan all full. I don’t know I’m just not sold on them.
Thank you for the video, I followed it and setup my network the same way. However, I have my wifi printer in the IOT network and and I can't print from devices on my other ssids like my 6ghz network. Is there a firewall rule I can add?
Great video. Could you tell me why you turn off the Autoscale when creating a new network please? Thank you
Could you do a video on setting firewall rules to allow a Sonos APP to work when inner VLAN blocking is configured?
the device is on the user network
Sonos is on the iOT network
Thanks!
Just checked my udm pro and it has traffic management installed. i of course set that up and tested it.
Thanks!
Thank you for the super thanks :)
Nice setup. It would be very interesting to know how much power these devices are consuming.
Nice 🙂
These videos are super helpful, It would be awesome if you could do a bit more of an in-depth video of the devices that should be connected to each network.
I am still at little confused as to what network we should be connecting all our computers and phones too, IoT or the default. Or how our smart devices talk to our phones if were on seperate networks?
Computers would be on a “trusted network” cell phones really are IoT devices.
But ya I should make another video explaining it better also different firewall rules :)
Lots of work on the IoT network, but what devices and such do I put on that network? Thanks for the video, it was fantastic!
Thanks for this best practice setup ;) Is it possible to use UID on the secondary WAN? I need a fixed IP, and mine is on WAN2...
as always a great video. Question : what are the shortcomings (if any) if the IoT network is created as a guest network? and will this eliminate the need for manual firewall rules + port and IP Groups?
i had a issue doing my IoT as a guest... partly because if you enable the guest network and landing page for WiFi, it kept trying to make guests go to the IoT network. I ended up doing my IoT and Guest networks as their own corporate networks and created the firewall rules then i didn't have issues with my WiFi guest network...
Hopefully they add an adopt all button in the future
I've been watching your videos for eons. I had a bad UDM Pro on a job that we replaced and imported the settings of the previous device (it would be accesible for 30ish minutes before crashing and was stuck on a very old version of software (around 3 years ago).
Anyways, while I'm watching this and I completely understand what you are teaching...I have my cameras at this location set on a different vlan. Remote access to the cameras worked previously to this new device going in with all of its software updates.
I am not sure how to set the appropriate rules in order to open up the NVR's port which is on the same vlan as the cameras themselves or if I am just wrong in that older setup and should move the camera nvr to the native network and create rules allowing cameras to communicate with it...which seems like it'd be a ton of extra work.
Watching this video, it seems to me that the Unifi Equipment is very simple to setup. I'm tempted to maybe give this stuff a try, I work in the Telecommunications Industry, ans I am only used to working on our equipment that we have.
It's very user friendly and there is a ton of information out there on how to get it setup
I honestly like your videos, so much information and helpful for someone new. But I have to replay the videos 20x for each step because you move/talk so fast. Slow it down a little bit :)
This was me trying to slow down 😂 will keep it in mind for the future as well
what are you using for off site video backups?
unifi blows for backing up records offsite.
Can you utilize the UDM PRO SE as the core/distro with Flex Minis switches hanging off of that? So ports 1-8 on the SE can we use them as uplinks going to the flex’s?
Hi. My question: How can i setup the countree on one-clict VPN? I would like use TIktok with other regio. Next question: I have UDM PRO plus IPS 2x1GB i setuped two WAN. But i would like mixing the speed to 2GB i cant. I use CAT 7 do you have suggest, or i need change to UDM SE?
Could you do a port forwarding tutorial I have bell also with the gigahub would love to know how to bridge mode it.
I appreciate the videos. Between you and crosstalk i just pre-setup my unifi stuff the other night (don't have it in use yet). If it's not too much to ask could you (or crosstalk, not that he'd see this comment) do a how-to to take a port from a switch and pass it through a docker on unraid to use its vpn. This way i can take a program on my pc and bind it to a port on the pc then plug that port into this switch port which would then vpn just that program and not have to install the vpn software (nord) that has already messed up my pc a couple times and was a chore to undo. Ive been debating trying to tue into an opnsense vm i stead of the udm for firewall.
Also maybe a "quickie video" on best practices of what items to put under what networks, pcs, smartphones, camers, servers/nas (unraid/truenas), network printers, etc.
Im a little green to switches.. does it make sense to put degices in seperate vlans if your not making firewall rules to block and allow traffic between them?
Hi nice video, everything works but i really cant make my cam network reach the nas. Some ideas ? (i can reach it from my defult network no prob)
Curious - Should I still be able to ping from a default connection over to an IP device on my Vlan when connected locally to my UDM pro? I don't have wifi access for my UDM Pro at the moment.
Hey Cody, I have a question: I have a Camera network set up on VLAN 30 and a corresponding WiFi network created for my G4 Instant cameras. However, when I adopt the Wifi cameras, they are adopted into my default network however, I am never able to migrate them to any VLAN network in Protect. Have you seen anything like this in the past and if so what's the fix? (Ps. I am able to connect other devices to the camera wifi network without incident.)
Can you configure NAT on the router? Someone says it lacks that capability.
in your experience whats the max users the special edition can handle without running into processing issues?
For a noob. I use a Unifi USG Security Gateway with an non managed switch (Netgear). With 1 LAN and 2 VLANs (IoT and Guest) is it possible for my cabled IoT devices like Philips Hue be placed on a VLAN (IoT) or do you have to have a managed switch and adress specific ports on the switch for a VLAN?
Matching your VLAN and Third Octet is so hot right now.
Great video, but I have a problem when connecting to any wifi guest network or any network connected to the vlans, I can't get the ip address
Would I create Firewall rules for VoIP just like IoT rules? The only firewall full I see that is default id the one created by UniFi called "Allow UniFi Talk Traffic" under "Internet Local". Since it is created by UniFi, I cannot see what is in this rule or how it is defined.
Noticed you didn't have any SSL/certificate issues when accessing the UDM Pro. Did you fix this manually or was it patched in?
Great video! Can you or have you created a video that goes over failover to LTE and to only funnel VOIP traffic and limits the bandwidth until WAN is restored?
Hey,
So we dont have the Unifi LTE here in Canada. It really is just a check box that you hit to tell which traffic to go over
i am a firm believer all vlan ports should be in the same interface processors on the switch (concurrent interface port#).. keep them together for easy troubleshooting...
new to unifi, quick question: what is port group RFC 1918 for?
does Unify device support NAT, URL Filtering (category-based) ?
Or do we have to dependent on 3rd party Firewall.
beautiful setup man, all unifi hardware all the way home, how long did it take you to get all of them?
can you use USG Pro 4 and UDM Pro in one network? if possible,how?
Does any of this change with the 3.x.x update? I am using the UDMP and we just got the 2.x.x and almost 3.x.x updates. I used your guide back in 2021with the 1.x.x firmware and the old UI, don't know if I need to redo it with new features.
Do you have any solution for sonos on a vlan, lots of outdated info, cant seem to get it working properly
Does this allow for default group to initiate connection with device on IOT and allow response but block iot device from initiating connection to default vlan?
In the section about creating networks you have your "third octet" set to 30 for your cameras. I'm attempting to follow along but it says it must be a valid IP etc etc. What's going on with that?
Awesome video! I got everything right except for the second part, I can still able to ping all my gateways. Any suggestion? Please help!
That would be the LAN_Local firewall rules you would need to adjust
Can you configure NAT on a USW Pro?
If we're going to be using unifi cameras (all wired), would there be a reason to have a separate virtual network for cameras? I can understand segregating third party cameras and NVR to another virtual network, but what would the reasoning be in this case? Just trying to learn more about proper procedures - thanks again for all the knowledge you share!
If possible, put differing devices on separate VLANs. It helps with overall bandwidth. Research data domains for more info.
When using Wireguard insted of openVPN, the block rules does not work. I can access all my subnets.
If you have Wifi cameras (G3 Instant, etc) would you also create a Camera Wifi and assign it to the Camera network? Also, can Wifi IoT devices just go on the Guest network since they just need internet access? Is there a reason to have them separated?
I have a WiFi network that is attached to my Camera network and have all of my WiFi cameras on that specific (hidden, obviously) SSID. This way, all of your WiFi cameras are automatically assigned to the Camera network.
I like this stuff but it seems lite. How can I get DNS on the lan to work? I have VPN using Windows VPN and can ping ip but not by name.
at 30:59, Why the type for UID VPN is LAN OUT instead of LAN IN? Thanks.
hey Mactelecom, are you going to do a video for "Unifi network complete setup 2023"?
Can you adopt your SE to another controller ?
The UI has changed significantly since this setup. Any plans on an update soon?
Great video! I followed all of your same process of creating the Profile for the Port and IP Groups for the RFC1918, then created all of the Firewall rules for our internal networks to be able to talk to the other vlans, but none of them can still ping the others... thoughts/suggestions?
I am seeing a similar issue, will post here with an update if I figure it out
In addition to the rule going from internal network to other vlans, I also made a "LAN IN" rule going the other way, from the vlan back to internal network. Then I started being able to ping as Cody was in the video with his NAS. Cheers, ev
Love your videos and all the info, but as a person in the IT field where our company uses Ubiquiti products, how on earth do you find availability? Is there an actual place where you can speak to a Ubiquiti rep, because we've tried everything to find a contact and an actual distributer that has stock of their products. Any advice or help would be amazing (cause it seems like a lot of youtubers, including people like Linus TechTips, have zero issues getting all of their products with ease) Thanks and please keep the content coming!
Due to China being locked down until Jan 23. Hope they can get going again soon. I have been buying from eBay to fulfill clients orders. Paying over the top for gear but keeps the client !!
When blocking ports 80, 443, 22 access to gateways, why do you exclude the source VLAN gateway from the destination group (you say "we don't want to put our IoT gateway in this group" at 17:33)? That requires you to create one destination IPV4 group for each source network (each excluding respective source networks' gateway, which is why you named the GW group "Block IoT to gateways" instead of just "All gateways" i suppose).
I tested to include all gateways in my lab network, and everything works fine (except for GW web access, which the VLAN users should not have anyway). This will reduce the number of IPV4 gateway groups from many to 1. Or have I misunderstood anything?
Brilliant tutorial!. Any chance we can get a 2023 refresh of this soon?.
Hey ya should be out sometime next week
Excellent mate 👌. Can't wait to see it.
@@MactelecomNetworks Long week :)
Do you have a link to the slim patch cables you prefer?
These ones are similar to the ones I use
amzn.to/3UmTAKN
Hello. I can't see the patch panel/rj45 blanks on the Unifi store (Europe, Great Briatain). Are your a third party product?
Here is one for you .
All seems well on local site and i can block and manage traffic between vlans etc., but with site to site VPN it doesn't matter what rule I put in place noting seems to block traffic between sites. I have two sites and i want management site to have full access to client site, but client site to have no access to management site
QQ: How do you separate isp bandwidth if possible. Lets say you have 2 gb coming in and only want to give 500 mb to guests services
Traffic Management, is there a way to block adult content as an option? Amazing job on this video!
Use the content filter in the network setup area
Any particular reason to get a NVR is you already have a Dream Machine Pro? Since the DMP can run unify protect seems like a waste to buy the NVR. Am I missing something?
Well Ubiquiti sent me a unvr pro to review so that’s the main reason. Also the UDM pro or se can only handle so many cameras
When assigning a VLAN to a specific port on my UDR, I get "An error has occurred while saving port configuration".. In fact, it says that no matter what I do.. I cant configure ports on my UDR and save it. I get that message... Pretty frustrating..
Bridge Mode? Can you make a video on how to open ports on Bell ISP router to point towards the UDM PRO to achieve bridge mode for VPN
Hey. I probably wont make a video on that but you just need to login to the bell modem then there is a section called port forwarding. There you just put the IP of your UDM Pro or SE
@@MactelecomNetworks Noob here, can you explain setting up port forwarding on the bell modem for passthrough?
I see you're lucky and got the 24 port Ent switch... I been trying to get that for months and it's always out of stock!
I believe Ubiquiti sent this switch to me for review
How many U is that network rack?
I have a dream machine pro and I have had to factory reset that 3 times now and the APs around my network because of firmware updates. I have no idea how people rate their products because I have had a nightmare with them. Nothing worse than being away and everything has gone down, and you just can't connect to do anything.