Getting ready to tackle my 1997 F350 4x4, 7.3 crew cab long box (same Truck) it is wandering back and forth going down the road . Thank you from Canada
Really appreciate the explanation of how all that you replaced affects the alignment. You can also count the threads to get a close as possible to the right alignment when replacing the outer tie rods.
I really enjoy your videos I have a 97 f350 4 door I tried that brand they lasted 3 months and I had to do it all over after trying a second time with the same results I broke down and bought moog lol good luck looking forward to more videos
Great video the only dude to take the whole unit out this is how ill do it i have new couplers so ill take it out make the new parts match exactly and pop it back in! Thank you!
What size socket did you use? And do i use metric or standard sockets.......i always get confused so thats why im askin....i dont want to strip bolts lol
I don't remember what size I used, probably a mix of both metric and standard. Sometimes a metric socket goes on a standard bolt a little tighter so I'll use that instead. Just use what fits the best!
In my case it only marginally helped since my steering gear box had the most play in it. The best way to check is to look under the truck at the tie rods while someone else turns the steering wheel. If your tie rods are worn out you'll see a noticeable amount of slop or delay between the pitman arm coming off the steering gearbox moving and the tie rods themselves moving the wheels.
My 97 F350 pulls hard to the right, my ball joints are all new my linkage doesn't look bent other then factory bend. I can't figure out what is going on with it
Buy a ball joint separator for 20 bucks at harbor freight. Best investment for these trucks as they chew tie rods up. Also buy the lifetime warranty ones and the Firestone lifetime alignment unless you know how to align yourself
Great video. but I purchased these parts from Oreilly's like suggested and after opening the boxes I noticed the ball joints pre-installed on the steering rod and center link looked VERY unusual ... dare I say incomplete or not quite good enough to even be called a Chinese part. The dust covers on the ball joints would simply lift up and were NOT clipped or in any way sealed ... what's the point of a zerk fitting if all you have to do is lift the boot and paste some grease in there. I assume this must be wrong, so I'll return them for some other brand and see if they're any better.
Thank you for the part numbers! This has been a nightmare trying to get the right ones.
Perfect. Now I feel comfortable doing this on my rig. Thank you good sir.
Great video. Just getting ready to do my 94 F250. Thanks so much for all the part numbers. That was awesome.
Once again, I have a job to do on the 96 F250 and you have a video on exactly what I'm looking for.
Getting ready to tackle my 1997 F350 4x4, 7.3 crew cab long box (same Truck) it is wandering back and forth going down the road . Thank you from Canada
Really appreciate the explanation of how all that you replaced affects the alignment. You can also count the threads to get a close as possible to the right alignment when replacing the outer tie rods.
I really enjoy your videos I have a 97 f350 4 door I tried that brand they lasted 3 months and I had to do it all over after trying a second time with the same results I broke down and bought moog lol good luck looking forward to more videos
I'm sorry to hear you had such a bad experience! I sure hope mine hold up better. Thanks for the heads up!
@@Rnddiesel well you might be good I live in Michigan our roads are terrible pot hole city
Great video the only dude to take the whole unit out this is how ill do it i have new couplers so ill take it out make the new parts match exactly and pop it back in! Thank you!
What size socket did you use? And do i use metric or standard sockets.......i always get confused so thats why im askin....i dont want to strip bolts lol
I don't remember what size I used, probably a mix of both metric and standard. Sometimes a metric socket goes on a standard bolt a little tighter so I'll use that instead. Just use what fits the best!
Just got into and accident today bent my Tie Rod only make left turns. The same day you post this.
I'm sorry to hear about the accident. I hope you're okay, and best of luck fixing the truck!
Can I just replace the bushings on the tie rod?
Thanks for the video, facing the same job soon, did it help tighten up your steering wheel? Mine has a lot of play at the wheel
In my case it only marginally helped since my steering gear box had the most play in it. The best way to check is to look under the truck at the tie rods while someone else turns the steering wheel. If your tie rods are worn out you'll see a noticeable amount of slop or delay between the pitman arm coming off the steering gearbox moving and the tie rods themselves moving the wheels.
Is this the dana5O? With 4.10 ratio?
Dana 60 right?
Pretty straight forward
what are your thoughts on your tires how many miles do you have on them and whatnot
Please, maybe you can help me. I need an adjuster in a equalizer bar. I have the same truck, but it's a Dooley. I have a 93.
Very helpful thank you
My 97 F350 pulls hard to the right, my ball joints are all new my linkage doesn't look bent other then factory bend. I can't figure out what is going on with it
One of the linkage ends could be frozen.
Is this the same for brick nose years?
I believe so, should be nearly identical
Buy a ball joint separator for 20 bucks at harbor freight. Best investment for these trucks as they chew tie rods up. Also buy the lifetime warranty ones and the Firestone lifetime alignment unless you know how to align yourself
Great video. but I purchased these parts from Oreilly's like suggested and after opening the boxes I noticed the ball joints pre-installed on the steering rod and center link looked VERY unusual ... dare I say incomplete or not quite good enough to even be called a Chinese part. The dust covers on the ball joints would simply lift up and were NOT clipped or in any way sealed ... what's the point of a zerk fitting if all you have to do is lift the boot and paste some grease in there. I assume this must be wrong, so I'll return them for some other brand and see if they're any better.
Would this work for a 1994 Ford Bronco XL 4WD?
I'm not sure about that, I think the Bronco's used a different front end arrangement with independent front suspension
Very detailed
Grate video again.
The adjustable camber bushings come in different degrees. You are better off letting the alignment shop do that.
maybe do a vid
Alright, well I actually just got a set of KO2's, are you referring to those or the old Nittos I had?
You don't know bro. We fix camber with cut and notched beams. West coast style .
This video was actually helpful. What’s wrong with you?