So I gotta say I did this on my stock mws mag last night and it ruined full auto for the mag. Spews gas everywhere and the cooldown is very noticeable. For semi I could see it being fine, but auto is much worse after doing this. I might even post a video comparing a stock mag to the gg modded ones because it's not the godsend everyone says it is.
@@Jaeger-Precision elite force green gas. I literally tested the mag before the mod and it worked perfectly and after it did maybe half a mag before spewing gas and just not cycling properly.
@@Jaeger-Precision please do! If you do a side by side comparison with the full auto performance of a regular mag and modded mag that would be great. I'll also do a similar test and video it.
@@jhqtech, it sounds like an overfilled magazine. The liquid gas to open space pressure isn’t correct which means it can spew out liquid gas which disrupts the full auto cycle. Try filling it with less gas (see if 2 - 3 seconds less works) and see if it works better. Even with filling it less with gas, it still should be more gas in the mag than a non-modded magazine.
Hi, I’ve been trying to fix the poor gas efficient of the marui akm mags for a while. I have 3 mags, they perform really bad compare to people who keep telling me how good a marui akm should be Does this modification effects the joules output? Cause now I’m using 12kg gas and 0.3G bbs, it sits around 1.3 joules and I can’t go any higher for cqb in my country
Did this on my mws mags, I was able to get 5 reloads before the gas runs out. Awesome mod! Thanks alot! :)
Awesome video thank you
can you please show us a video how to change the unifeed magazine lip pls?
done this on my mags a few months back when i got them, i just dremem'd off about an inch from the bottom :D
how does it work so far? does cutting only an inch prevent the mag from overfilling?
Did the same thing. Works like a charm 😊
wouldnt there be a risk of getting filings in the tube and then subsequently in the mag in you chop some of it off?
I assume with the longer inner valve the over filling risk that the MWS mags have with this mod is removed?
Yes
So what's the purpose of the tube then, why did they put it in if it has no function? It seems like it must have some purposes.
prevent overfilling
does this mod gain more fps ?
Hey mate what's the lubricant pen you are using? Could do with adding that to my tool bench 😎👍
You can get the on the Jaeger Precision website. Its the ONE pen
Ordered 😎 thanks for that mate be a great addition to my work bench and toolbox 👍
So I gotta say I did this on my stock mws mag last night and it ruined full auto for the mag. Spews gas everywhere and the cooldown is very noticeable. For semi I could see it being fine, but auto is much worse after doing this. I might even post a video comparing a stock mag to the gg modded ones because it's not the godsend everyone says it is.
Maybe its the propellant your using. I have 12 magazines here all modded and none of them do that
@@Jaeger-Precision elite force green gas. I literally tested the mag before the mod and it worked perfectly and after it did maybe half a mag before spewing gas and just not cycling properly.
@@jhqtech i would sag the magazine is too cold after filling. I can shoot a video to prove it if needed.
@@Jaeger-Precision please do! If you do a side by side comparison with the full auto performance of a regular mag and modded mag that would be great. I'll also do a similar test and video it.
@@jhqtech, it sounds like an overfilled magazine. The liquid gas to open space pressure isn’t correct which means it can spew out liquid gas which disrupts the full auto cycle. Try filling it with less gas (see if 2 - 3 seconds less works) and see if it works better. Even with filling it less with gas, it still should be more gas in the mag than a non-modded magazine.
Did you say the TM MTR 16 was you favourite rif?
I don't think I did, did I? 🤔 The MWS system in general which includes the MTR16 are the GOAT!
@@Jaeger-Precision I heard you say it on one of your vids but I have been listening all day while out walking
@@danfieldhouseeee it is a good platform to build on as you get the receiver which can be engraved to have on whatever you like
Won't it make the cooldown of the mag worse?
not experienced anything like that no
A lot
Tube on mine was impossible to pull out. Actually split the oring and damaged the lip above it trying to pull it out, didnt even budge an inch.
Hi, I’ve been trying to fix the poor gas efficient of the marui akm mags for a while.
I have 3 mags, they perform really bad compare to people who keep telling me how good a marui akm should be
Does this modification effects the joules output? Cause now I’m using 12kg gas and 0.3G bbs, it sits around 1.3 joules and I can’t go any higher for cqb in my country
No its doesnt effect power