Wow, That drill has amazing torque! Seems to be just as powerful as a corded drill. The new brushless equipment is very impressive. I'm a Bosch fan and I'm waiting for Bosch to release a brushless impact driver in the States.
Hi, unfortunately they only advertise the hard torque. The maximum capacity is 10x400 (screw with full thread). The last screw i drove in was a 10x300mm screw but only with half thread. 8mm screws are no problem at all. I will try to measure the torque....However if you look for a drill/driver and want to drive mostly or a lot of screws i would probably get the Festool/Protool DRC because the Centrotec system has a unsurpassed runout and it´s more pleasing to drive screws with it....
Hey Monte, you wouldn't happen to know what the soft torque of this drill is? I notice they advertise max torque at 90NM but I imagine that being a "hard torque" value and soft torque is more important... So what does this baby stall at? I noticed you doing a nice torque test with your Milwaukee drill. Any chance you could replicate a test like that with this Fein drill? I'm wondering if this has more power than the Festool DRC/PDC.
hast du beim schrauben der 8er und 10er schrauben ein drehmoment eingestellt ? weil der schrauber abschaltet. das sollte auf der bohr einstellung nicht sein.
Wie ist das zu verstehen ? Durch zu "schnelle" Bedienung des "Start Knopfes" am "Akku Schrauber" schaltete der "Schrauber" ab der Aufnahme Zeit (2:30min.) im 1.Gang ab !? Und durch zu "langsame" Bedienung des "Start Knopfes" am "Akku Schrauber" schaltete der Schrauber ab der Aufnahme Zeit (2:37min.) im 1.Gang nicht ab !?
Du solltest die Drehmomentvorwahl deaktivieren,(Bohrstufe) denn wenn du den Trigger nur zum Teil betätigst kommt der Motor nicht auf Drehzahl und kühlt somit auch nicht ausreichend auf Dauer bekommst so die Maschine kaputt ohne das du ihre ganze Leistung nutzt. Dann klappt das auch mit der großen Spax ohne Probleme.
Wow, That drill has amazing torque! Seems to be just as powerful as a corded drill. The new brushless equipment is very impressive. I'm a Bosch fan and I'm waiting for Bosch to release a brushless impact driver in the States.
Hi, unfortunately they only advertise the hard torque. The maximum capacity is 10x400 (screw with full thread). The last screw i drove in was a 10x300mm screw but only with half thread. 8mm screws are no problem at all. I will try to measure the torque....However if you look for a drill/driver and want to drive mostly or a lot of screws i would probably get the Festool/Protool DRC because the Centrotec system has a unsurpassed runout and it´s more pleasing to drive screws with it....
The next generation of Bosch power tools most likely will have brushless motors too !
just got a flyer from my dealer and they state 46NM soft torque for the ASCM 18
Hey Monte, you wouldn't happen to know what the soft torque of this drill is? I notice they advertise max torque at 90NM but I imagine that being a "hard torque" value and soft torque is more important...
So what does this baby stall at? I noticed you doing a nice torque test with your Milwaukee drill. Any chance you could replicate a test like that with this Fein drill? I'm wondering if this has more power than the Festool DRC/PDC.
ja war mit Drehmoment um zu schauen bis zu welchem Schraubendurchmesser das funktioniert.
hast du beim schrauben der 8er und 10er schrauben ein drehmoment eingestellt ? weil der schrauber abschaltet. das sollte auf der bohr einstellung nicht sein.
War auf Bohrstufe. Abschaltung um den Akku zu schützen denke Ich.
@@monteLS1988 danke für die antwort nach 7 jahren :D
@@kriegarsch3246 Besser spät als nie :D lol
Wie ist das zu verstehen ? Durch zu "schnelle" Bedienung des "Start Knopfes" am "Akku Schrauber" schaltete der "Schrauber" ab der Aufnahme Zeit (2:30min.) im 1.Gang ab !?
Und durch zu "langsame" Bedienung des "Start Knopfes" am "Akku Schrauber" schaltete der Schrauber ab der Aufnahme Zeit (2:37min.) im 1.Gang nicht ab !?
jo :D
Verstehe. Und danke für die Rückmeldung.
Du solltest die Drehmomentvorwahl deaktivieren,(Bohrstufe) denn wenn du den Trigger nur zum Teil betätigst kommt der Motor nicht auf Drehzahl und kühlt somit auch nicht ausreichend auf Dauer bekommst so die Maschine kaputt ohne das du ihre ganze Leistung nutzt. Dann klappt das auch mit der großen Spax ohne Probleme.