Tumble Dryer Error Codes E61, E62, E63, E64 E65,E66,E67 Electrolux, AEG, Zanussi
HTML-код
- Опубликовано: 25 авг 2024
- Get your appliance fixed faster! Click the link below to browse our supplier's huge selection of appliance parts and support the channel at the same time! (repairpartstea...)
Tutorial: www.how-to-repa...
E6 Family of Error Codes for Env06 Tumble dryer boards, this will flash 6 Green followed by a number of red flashes.
These error codes are for ENVo6 Cuirct boards tumble dryer Electrolux, AEG, Arthur Martin, Elektro Helios, Eureka, Faure, Frigidaire, Gibson Appliance, Husqvarna, Kelvinator, Marijnen, Parkinson Cowan, Progress, Simpson, Tornado, Tricity Bendix, Volta, Westinghouse, Zanker, Zanussi, Zoppas.
Please remember to subscribe to our channel
www.youtube.co...
Remember to Shop with www.how-to-repair.com and it would help us by posting the video or the website on your timeline. This helps us a lot and if we really helped you can always buy us a beer how-to-repair.c...
Please remember to mark us to your favourites also I would be grateful if you would subscribe to our channels social media as this really helps my site and keeps us going.
RUclips. / apart4u
Facebook. / how.to.repair.appliances
Hi guys, if your aeg/Electrolux/zanussi heat pump dryer is running 30 minutes normally and then giving e60 (e63 in test mode) just checked the upper capasitor which should be 10uf. You will see it is around 4.5 - 5.0 that is a fault.. I finally solved it. Just replace the 10uf capasitor (the above one, connected to engine motor), no soldering or antything, it is plug and play. Buy it from an electronic market showing the old faulty one, do not buy it from an AEG or other brand shoppers. Otherwise it will be 10 times expensive. There is space to place it into the machine,, so the new one can be a little fat or long, no matter, just be carefull for the values like voltage etc. They are not polarized so you can attach the 2 cables whatever you want. You don't need to disassebly tumble or any thing. Just get the back top and right panel, you will see the 10uf capasitor lying horizontally. Fyi, the below one is 18uf and you need to diassemble tumble and other things to get it back, but fourtunately you can measure it without disassemble.
Helped me identify a faulty thermostat on my EDC 67550 Electrolux dryer.
Thanks a lot !
Brilliant, managed to fix it, thank you!
I got a fridge air infinity dryer I had replaced my heater element and After three dryer used I got a e65
Hello, any advice on the E66 error?
Thanks, I am trying this tomorrow, hope it works, I'll let you know, Well so you can tell me how good I did or give me more help.
Can you do us a favour and please share this video on your timeline.
This will help other people who can’t get engineers out to help them.
ruclips.net/video/rFyGAHVFUW8/видео.html&t
Stay safe
Can you advise on E66 error and how to reset.
Thank you so much.
Have a john lewis jltdc09 with orginal problem was no heat changed the heater for a new one however tumble dryer is now doing full cycle still no heat cleared the error code e62. Still no heat goe back jnto settings went to number 5 on the dial starts then beeps again with error e62 please help also have changed the condenser resistor.
hi ,, im asking what the possible cause of my electrolux dryer ede67550w .. first i found the LNk blows and resistor 47 ohms , after i replaced it.. the circuit board didnt power on and no lights lit from led. thanksż
imam problem sa eletroluksovom susilicom.izbacuje gresku E32 kad ukljucim program autotestiranja.i poslije restartovanja greske ponovo izbacuje E70 gresku?molim za pomoc ako Mrko zna il je imao isti problem.
Ja imamisti problem. Da li ste saznali sta je u pitanju?
Can you help me please. I checked heater and termostat. They are ok. Dryer still dont produce heat.
It is possible, it could be the relay on the circuit board. If you have a look on our channel, you will find videos about tumble dryer relays. There are also other sensors and thermostats at the front of the machine. Make sure you have checked all them as well.
Heater and pcb both must be changed at same time.
Front load washing machine error code E33.problem is and drum not rolling water not receiving
Tiene que ser español o traducido del ingles
thx for help. EXTRA
We have an AEG LAVATHERM 86590IH3 dryer. (Type TC12H6BHP). After normal operation we found lots of water under the dryer! When I opened the filter door, there were lots of water in that area. I have started investigating the pump area at the back of the machine. I have determined with a digital multimeter that the resistance of the pump was about 750 ohm. In one of the videos the repairman mentioned that according to the service manual it should be about 750 ohm. So at this moment I assume that the pump is OK....... Next I will try to check the float sensor/switch which turns on/off the pump. Am I on the right path? Has anyone ever experienced this problem before? (I have not put the machine into diagnostics mode, yet).
E62 brandt