Attach a pully to it and drive it with a small water wheel. Rectify the AC 3 phase output with a bridge rectifier. Use that to feed a power converter of your choice. The DC voltage is 220 to 415V depending on speed. This allows you to power most switch mode power supplies bypassing the front end voltage doubler. The rig job I built used a bicycle wheel attached to the water wheel shaft as the primary pully and an engine pully as the receiver giving about 277V at 4A of current. This fed a charging unit that charged a 24V battery array used in an off grid setup. ❤
Bonne idée et bon partage ,Merci . Mais pour ceux qui veulent la réaliser , il va falloir trouver un Moteur et c'est cela le plus difficile !! Merci . Good idea and good sharing, thanks. But for those who want to realize it, it will have to find an engine and it is the most difficult! Thank you .
You should have measured the voltage with the light bulb attached. The voltage would probably have been a lot lower than what you read open circuit. You will get a more accurate idea of what it can do if you measure voltage and current at the same time. Assuming it was a 220V motor you will need to spin it at the speed it runs at as a motor to generate 1200 watts, if even that much.
my friend's table is going out a bit;) But the idea is sensational! Have you ever thought about using neodymium magnets? And add a mass wheel somewhere 100kg (with a relieving gear) - if at first it was possible to disperse such a wheel and support such a mass-scattering engine with low power, then maybe the energy production would have a surplus?
As you put a load on the wires, the resistance in magnetic field grows. You need a really hard to push to make the power real. You need a water turbine and a lot of water to push the turbine.
Ponle eso a una turbina tesla y un container a presión y con un ariete lo subes hasta arriba y solo tienes que dejar bajar el agua y con la, misma fuerza de subida llenas un deposito que vierte en presión y aprovecha esa fuerza para generar vueltas sin pérdidas. Patenta
Mr Electron At minute 3:31 you sample some ferrous magnets attached to the shell. Are those magnets in the washing machines? or Did you put those magnets in there?
Excellent work, simple, practical and very illustrative. Could someone tell me or help me indicating what kind of work should be done with the wiring of the coils? Greetings from Colombia
Do not break your washing machine for salvaging the motor, it may have an older induction motor or universal motor. Both are complicated to be used as generator.
Mr, Electron, thanks for the video. Problem, can light lightbulbs easily, but when i hook motor to it i get a lot of resistance. I'm just using my cordless drill, it will start smoking. hown to cut resistance. Pennsylvania USA.
A guy on u tube made a belted cycle from a frount loader washing machine...and to my surprise the motor was brushed....like used in power tools providing rim bending axle breaking torque
Buen video amigo, sigue con este proyecto, tengo unos motores de esos y no sabía en qué emplearlos, con tu ayuda ya podré usarlos, felicidades desde México !!!
You can rectify 3 phase to one phase by using a three phase generator rectfier input three phase Output +- The second note Measuring amperage is wrong The ampere is measured under load only in series By man hand you can only get 200 watt maximum
with a pedal bikes sprocket set for gearing and a chain from it to a turbine made out if a light large pedal bike rim it can make good power .... i knew someone that use to use that setup to charge there battery banks
Es ist ein guter Ventilator für Roboter, um nicht zu überhitzen. Dies ist kein Dynamo. Ein Dynamo holt die gesamte Induktivitätsreserve aus einem Metall mit höchster Felddichte wie Eisen und Kobald. Dies ist ein Dispenser und ein Felddisperator. 1200 Watt sind Unsinn. Vielleicht brauchst du 1200W eine kleine Rotation in einem verzweifelten und zerschnipseltem Magnetfeld auszulösen.
rewire it , divide the stator up, so you have less coils per phase , say 4 coils or so, series paralell, youd have lower voltage output but better as a charger yet at higher rpms , like a wind turbine
Similar to this I found motor in e bike wheel difference was it was with permanent neodium magnets in wheel rotor...responsible for super torque from standstill without gear ...used as a generator it will genrate high voltage at low rpms...do try it out...
Here's an idea for future....attach a gear ratio unit.....from big gear too small gear thus turning more revolutions....use your hand crank or optional motor maybe.
Mr Electron Very nice concept of using BLDC motor of an old washing machine. But, the table on which the generator is kept is shaking a lot which is causing instability in genarating the power.
you shuld make the rotation easy bay adding som centrak bearing and yo can use it as a wind turbine it need jus good blades ti rotate the central magnit shaft
You have, at most...a 50W generator. Even IF you could claim that max generated power was from S.C. current and O.C. voltage, giving you say 1200W, you wouldn't even come come to turning it by hand. A human (top athlete) can MAYBE output 1kW for a few seconds. These motors would be well suited for hydro generation.
I am trying to find a set up that I can hook a inline 6 cylinder motor to running on wood power and generate approximately 5000 watts at 220 volt 3 phase?
You can't imagine how dangerous is that grinder with the blade. I used once to cut a piece of plywood and I got a nail,cutting my leg. Be careful, never use that blade to the grinder
Great video, but do you need to rewire the the coil to generate power, or just remove from the washing machine and connect to load , crank it and you get power
It's as 220Vac 3 phase motor/it's cam operate as generator because it has permanent magnets. Whei you spin the generator the nominal voltage will be 220vac. In my home I have a hibrid solar invert that work with a DC voltage up to 450vdc. To my needs it is perfect. In shorts you just need a concerter that can run on the vintage of. Your generator. It this motor is too much for you. You need to rewind the coils or use hover board motor that have 70vdc max on out put but only 250w
Mana ak video ma daka ta campine mad sirs coli ko prlal kardia hai. Aisa karna ka kia motlov hai batao plis sar. Gis video ma daka ta us chanl ka nam (stefan stoove). Video ka nam rewiring a smartdrive motor for hydro wind generator. Plis replly me. Thinks.
Salve, ho ricablato uno statore uguale a questo a 36 poli, ho cambiato il filo di tutti i poli con un filo del diametro da 1,50mm e cablato lo statore in 6x2c (originale era di 0,90 mm) ottenendo cosi 12/24 volt, trasformandolo in un generatore eolico per poter caricare delle batterie complessivamente di 400 AH, 12 volt, le chiedo come posso calcolare i watt e gli amper di questo generatore conoscendo solo i volt? grazie.
I'm back, don't why my meter was reading so low, hooked things up again, with hand crank getting 50, 60 volts, hooked drill to it lighting a LED light bulb, very bright. Need a speed controller. going to hook a 12 volt dc motor to it, hopefully charge battery and do some work.
absolutely? no. but the Design of a machine intended to function as a motor, has been Optimized for that function (and NOT as a pma). so, MODS are needed in order to Improve performance. googletranslate
if i send you vid of my project do you think you can help me work out the bugs.i have been working on it for two three mounts now and have no clue what i have dun wrong . not a lot of people r n to this type of thing but you are
Con una turbina de impulsó de aire es muy eficaz se hace con rines de aluminio en desuso.y son muy livianos y tienen muchas revoluciones.y fáciles de cortar para insertar las aspas.en los dos bornes del rin el rin va dentro de un tubo ya sea un bote cubeta o enlaminado para que haga presión.el aire.es muy eficiente.
Bravo! Un experiment excelent , daca poti gasi 10 motoare de masina de spalat identice punele pe un ax si invartile cu ajutorul unei turbine eoliene , cu un controler , baterii si un inverter de 4 sau 8kw devii independent energetic (cand bate vantul)😀, oricum multumesc pentru experiment si rezultatele acestuia
@@popaconstantin4615 corect!dacă are multe,dar mai bine ar fi dacă ar înlocui magneții cu alții neodymium iar bobinele sa fie din cupru,2 motoare puse pe același ax,elicele de peste 2metri radius,la 10 m înălțime as mai crede ca scoate peste 1,5kw
Brother I have done the air wind generator with the help of Lg washing machine direct drive motor iam getting the Ac 90volt but I need to convert into Dc12volt 10amps needed for battery charging what should I do please help me
get ready properly and than you do the prectical work my son .i did this when i was your age.take time get ready.,you are smart but no patience. am i right ?
Colocale la rueda trasera de una bicicleta y pedalea la bicicleta y obtendrás muchos voltios mas de 220v. Porque tu generador necesita una multiplicación que te la daría la rueda mas grande que esa !!!
Eduardo tengo uno igual en España, quiero hacer un generador y tengo algunas dudas sobre el tema eléctrico, si sabes de esto te agradeceria charlar y quizás me despejes las dudas, este es mi WhatsApp y telegram +34636111188 si puedes o alguien sabe les agradecería para darle un uso. Gracias
@@ramongarciaguerra5267 un generador para alimentar que cosa primero debes empezar por que vas a alimentar saca el numero de consumo del aparato que vas a alimentar y ve si tu generador alimentara siempre mas de ese consumo
Hello amigo Aqui é do Brasil... faça uma ligação em Delta Ligue as às 36 bobina em série ligue o final do Fio Amarelo ligue no início do vermelho o final do vermelho ligue no início do segundo no início do azul e o final do azul ligue no início do Amarelo em cada uma Emenda sairá os três fios para a ponte retificadora...🔼(1 e 2) (2 e 3) 3 e 4) (4 e 5) (5 e1 em cada uma dessas emenda sai para a retificação
BEST BATTERY CHARGER DIY VIDEO - ruclips.net/video/ZN3saILbYUw/видео.htmlsi=9_nLu0vKOqfn4zi_
*Join this channel to get access to perks:*
ruclips.net/channel/UCWFbPzBb7dCyCWuBA-DBrMAjoin
*Mr.Electron Patreon's Page* - www.patreon.com/mrelectron
*Hindi Channel* - www.youtube.com/@Mr.ElectronHindi
*Alternator Channel* - www.youtube.com/@mrelectron_alternator
*Watsapp Channel* - whatsapp.com/channel/0029VaQmmRaFCCoWOf7huh3G
Finally a little technical device that could work. I would even consider the reported performance to be real
Attach a pully to it and drive it with a small water wheel. Rectify the AC 3 phase output with a bridge rectifier. Use that to feed a power converter of your choice. The DC voltage is 220 to 415V depending on speed. This allows you to power most switch mode power supplies bypassing the front end voltage doubler. The rig job I built used a bicycle wheel attached to the water wheel shaft as the primary pully and an engine pully as the receiver giving about 277V at 4A of current. This fed a charging unit that charged a 24V battery array used in an off grid setup. ❤
You r a very good student.... All your projects are super...
Ide brilliant kak saya sangat suka video ini bisa menambah ilmu saya... 👍👍👍
I like your this video because of load test and other kinds of load test .
Bonne idée et bon partage ,Merci . Mais pour ceux qui veulent la réaliser , il va falloir trouver un Moteur et c'est cela le plus difficile !! Merci .
Good idea and good sharing, thanks. But for those who want to realize it, it will have to find an engine and it is the most difficult! Thank you .
Em ferro velho tem
You should have measured the voltage with the light bulb attached. The voltage would probably have been a lot lower than what you read open circuit. You will get a more accurate idea of what it can do if you measure voltage and current at the same time. Assuming it was a 220V motor you will need to spin it at the speed it runs at as a motor to generate 1200 watts, if even that much.
Yes. This engine has an obout 9A @22V -> 200W
my friend's table is going out a bit;)
But the idea is sensational! Have you ever thought about using neodymium magnets? And add a mass wheel somewhere 100kg (with a relieving gear) - if at first it was possible to disperse such a wheel and support such a mass-scattering engine with low power, then maybe the energy production would have a surplus?
What all would this run appliances wise if I may ask .
When it can produce 220 volts and 6 amps at the SAME TIME, then you'll have a 1200 watt generator.
my thoughts 100%
Very good for domestic power plant
Si me quedo toda la no he dando manivela .......GLORIOSO
As you put a load on the wires, the resistance in magnetic field grows. You need a really hard to push to make the power real. You need a water turbine and a lot of water to push the turbine.
indeed
In my spare time I go to my friend who runs scrape shop their i have disected lot of machines ...with all time favourite tool the angle grinder
Having some smoothing capacitors will help.
Do you feel resistance when you turn your generator? To much resistance for making a wind mill?
I'm glad you put that guard on the grinder at 00:09. Looks a little dangerous!
One get a stuffer table two hook it up to a push bike three love it
Ponle eso a una turbina tesla y un container a presión y con un ariete lo subes hasta arriba y solo tienes que dejar bajar el agua y con la, misma fuerza de subida llenas un deposito que vierte en presión y aprovecha esa fuerza para generar vueltas sin pérdidas. Patenta
You’re nearly there, just need to reach 88mph and don’t forget the flux capacitor!
To get this to any usage .. in a wind turbine you need a 3 way rectifier AC to DC
And a 200v MPPT EPever 6415 or MidNite 250v MPPT
To CHARDGE BATTERY
Mr Electron
At minute 3:31 you sample some ferrous magnets attached to the shell.
Are those magnets in the washing machines? or
Did you put those magnets in there?
They come with the washing machine
Sir, Did you change the winding?
Excellent work, simple, practical and very illustrative. Could someone tell me or help me indicating what kind of work should be done with the wiring of the coils? Greetings from Colombia
Do not break your washing machine for salvaging the motor, it may have an older induction motor or universal motor. Both are complicated to be used as generator.
Вот бы мне такой зелёный диск на болгарку, такого диска у меня ещё не было😁🙃
nice thing conect MOT.. ez HV gain.. it is basicly nescesary keep voltage high and curent low..
Just by changing the wiring of the stator into star rather than delta would make low rpm higher watt output you can find these instructions easily
They are in star configuration, but the neutral is behind the hall sensor
Mr, Electron, thanks for the video. Problem, can light lightbulbs easily, but when i hook motor to it i get a lot of resistance. I'm just using my cordless drill, it will start smoking. hown to cut resistance. Pennsylvania USA.
A guy on u tube made a belted cycle from a frount loader washing machine...and to my surprise the motor was brushed....like used in power tools providing rim bending axle breaking torque
Buen video amigo, sigue con este proyecto, tengo unos motores de esos y no sabía en qué emplearlos, con tu ayuda ya podré usarlos, felicidades desde México !!!
Donde se encuentran estos motores , en que se usan ?
You can rectify 3 phase to one phase by using a three phase generator rectfier input three phase
Output +-
The second note
Measuring amperage is wrong
The ampere is measured under load only in series
By man hand you can only get 200 watt maximum
he was measuring voltage not current
@@sma221042
Time In 8:50 measuring current for one phase
Can we use at home practically?for home appliances
with a pedal bikes sprocket set for gearing and a chain from it to a turbine made out if a light large pedal bike rim it can make good power .... i knew someone that use to use that setup to charge there battery banks
Noch alle Finger dran. Gott sei Dank.
Все честно и познавательно молодец.
Great job son and keep up the interest in what your doing.One day it will become free for your taking. [ You'll figure it out. ]
man thanks for content 😂😂 but please use more steady table for next time, my head still all spinning after watching this😂😂
Sorry about that 😀
Não aperte porcas com alicate amigo vc é bom demais pra isso.
Es ist ein guter Ventilator für Roboter, um nicht zu überhitzen.
Dies ist kein Dynamo. Ein Dynamo holt die gesamte Induktivitätsreserve aus einem Metall mit höchster Felddichte wie Eisen und Kobald. Dies ist ein Dispenser und ein Felddisperator. 1200 Watt sind Unsinn. Vielleicht brauchst du 1200W eine kleine Rotation in einem verzweifelten und zerschnipseltem Magnetfeld auszulösen.
I've been trying for a while to get my hands on one of those motors to play with.
Can you rotate it with a cordless drill?
yeah !!!!
wind gen kits
made by fischer and paykel. some other companies use 'em, also. maybe whirlpool. googletranslate
Este ya me gusta por qué sin aire puedes alimentar la batería, o encender bombillas led de 12voltios.
rewire it , divide the stator up, so you have less coils per phase , say 4 coils or so, series paralell, youd have lower voltage output but better as a charger yet at higher rpms , like a wind turbine
Similar to this I found motor in e bike wheel difference was it was with permanent neodium magnets in wheel rotor...responsible for super torque from standstill without gear ...used as a generator it will genrate high voltage at low rpms...do try it out...
Nice job what brand of Washing machine are you using
Felicitaciones, cumple con las leyes de la termodinámica, y la de Faraday. Excelente video.
Jadi kepengen punya dinamonya. Mau ku coba dirumah
Here's an idea for future....attach a gear ratio unit.....from big gear too small gear thus turning more revolutions....use your hand crank or optional motor maybe.
Esas lámparas se prendes con cualquier cosa
Mr Electron Very nice concept of using BLDC motor of an old washing machine. But, the table on which the generator is kept is shaking a lot which is causing instability in genarating the power.
Nice. Instead of hand crank, install peddles n you should get more power
E riksha motor bhi kaam me le salte h kya vo kitna volt and amper nikalegi
I have this motor but don't know how to run it. Could you please make a video on it to run on ac current
Can u check this with a spark gap and a capacitor attached in series and chk the amperage drawn with load
Turn those channel locks around lol, they are made to barely have to squeeze with your hand if you use them the correct way
It's nice experiment
you shuld make the rotation easy bay adding som centrak bearing and yo can use it as a wind turbine it need jus good blades ti rotate the central magnit shaft
You have, at most...a 50W generator. Even IF you could claim that max generated power was from S.C. current and O.C. voltage, giving you say 1200W, you wouldn't even come come to turning it by hand. A human (top athlete) can MAYBE output 1kW for a few seconds. These motors would be well suited for hydro generation.
I am trying to find a set up that I can hook a inline 6 cylinder motor to running on wood power and generate approximately 5000 watts at 220 volt 3 phase?
Can you provide this washing motor ?? If you are having from scrap ??
You can't imagine how dangerous is that grinder with the blade. I used once to cut a piece of plywood and I got a nail,cutting my leg. Be careful, never use that blade to the grinder
The poor guy doesn't even have a sturdy table!
Brother plz aap hindi me samjhaya karo..to best hoga...bldc motor ko ac se direct connection pe kaise start kiya jaye
im wonder how much original spesification power (watt) of the washing machine motor ?
does it need much forse to turn
BOM DIA. COM O SEU CONHECIMENTO. ABRIU A MIM UM PROJETO BASEADO NO SEU SURPREENDENTEMENTE. .OBRIGADO. FORTE ABRAÇO
A table with rigid legs is necessary.
It's very good home made masters project.
فكرة احترافية 😮😮😱😱👍👍👍👍
Wow good 👍👍😊👍 🌟🌟🌟
Great video, but do you need to rewire the the coil to generate power, or just remove from the washing machine and connect to load , crank it and you get power
It's as 220Vac 3 phase motor/it's cam operate as generator because it has permanent magnets. Whei you spin the generator the nominal voltage will be 220vac. In my home I have a hibrid solar invert that work with a DC voltage up to 450vdc. To my needs it is perfect. In shorts you just need a concerter that can run on the vintage of. Your generator. It this motor is too much for you. You need to rewind the coils or use hover board motor that have 70vdc max on out put but only 250w
Mana ak video ma daka ta campine mad sirs coli ko prlal kardia hai. Aisa karna ka kia motlov hai batao plis sar. Gis video ma daka ta us chanl ka nam (stefan stoove). Video ka nam rewiring a smartdrive motor for hydro wind generator. Plis replly me. Thinks.
Salve, ho ricablato uno statore uguale a questo a 36 poli, ho cambiato il filo di tutti i poli con un filo del diametro da 1,50mm e cablato lo statore in 6x2c (originale era di 0,90 mm) ottenendo cosi 12/24 volt, trasformandolo in un generatore eolico per poter caricare delle batterie complessivamente di 400 AH, 12 volt, le chiedo come posso calcolare i watt e gli amper di questo generatore conoscendo solo i volt? grazie.
I'm back, don't why my meter was reading so low, hooked things up again, with hand crank getting 50, 60 volts, hooked drill to it lighting a LED light bulb, very bright. Need a speed controller. going to hook a 12 volt dc motor to it, hopefully charge battery and do some work.
I have watched in other videos that they rewind the same type of motor to work as generator. Is it absolutely essential to do that?
Not at all.
absolutely? no. but the Design of a machine intended to function as a motor, has been Optimized for that function (and NOT as a pma). so, MODS are needed in order to Improve performance. googletranslate
Your work on the coils is great, but change the spin handle... no way
like to see it hooked up to a bike, is this washer in the USA?
Angle grinder is my fav tool too lol
if i send you vid of my project do you think you can help me work out the bugs.i have been working on it for two three mounts now and have no clue what i have dun wrong . not a lot of people r n to this type of thing but you are
Exelente video un saludo desde mexico
Just got done with same set up, only getting .50 volt, something not telling us, what do we need to no. Pennsylvania USA.
if you divide the coils 24 into 3 8 per x 3 sections, easier then to turn the motor
This could be part of a solution for an EV range extender, thanks for the inspiration.
And they are.. mainly in regenerative braking
Patent pending got a generator similar to this that will go into electric vehicles inside the rim
Con una turbina de impulsó de aire es muy eficaz se hace con rines de aluminio en desuso.y son muy livianos y tienen muchas revoluciones.y fáciles de cortar para insertar las aspas.en los dos bornes del rin el rin va dentro de un tubo ya sea un bote cubeta o enlaminado para que haga presión.el aire.es muy eficiente.
Bravo! Un experiment excelent , daca poti gasi 10 motoare de masina de spalat identice punele pe un ax si invartile cu ajutorul unei turbine eoliene , cu un controler , baterii si un inverter de 4 sau 8kw devii independent energetic (cand bate vantul)😀, oricum multumesc pentru experiment si rezultatele acestuia
motorul asta folosit ca generator abia daca scoate 200 wati maxim
@@cipry1010 din acest motiv am spus sa puna 10 bucati pe axul unui rotor eolian ca sa ai lejer 2 kwh.
@@popaconstantin4615 corect!dacă are multe,dar mai bine ar fi dacă ar înlocui magneții cu alții neodymium iar bobinele sa fie din cupru,2 motoare puse pe același ax,elicele de peste 2metri radius,la 10 m înălțime as mai crede ca scoate peste 1,5kw
Where this type of coil is available
Eu José Ferreira da Rocha gostaria de participar Deste progeto
Why didn't you clean up the bearings and such to allow them to move more freely?
Brother I have done the air wind generator with the help of Lg washing machine direct drive motor iam getting the Ac 90volt but I need to convert into Dc12volt 10amps needed for battery charging what should I do please help me
get ready properly and than you do the prectical work my son .i did this when i was your age.take time get ready.,you are smart but no patience. am i right ?
Cool experiment
If you want that thing you can buy at online store its name is "direct stator" its ussually find in machine wash front loading
Colocale la rueda trasera de una bicicleta y pedalea la bicicleta y obtendrás muchos voltios mas de 220v. Porque tu generador necesita una multiplicación que te la daría la rueda mas grande que esa !!!
Eduardo tengo uno igual en España, quiero hacer un generador y tengo algunas dudas sobre el tema eléctrico, si sabes de esto te agradeceria charlar y quizás me despejes las dudas, este es mi WhatsApp y telegram
+34636111188 si puedes o alguien sabe les agradecería para darle un uso. Gracias
@@ramongarciaguerra5267 un generador para alimentar que cosa primero debes empezar por que vas a alimentar saca el numero de consumo del aparato que vas a alimentar y ve si tu generador alimentara siempre mas de ese consumo
@@eduardolunacastro4718 gracias por su pronta respuesta, esa no es la duda pero gracias x contestar un saludo
Nice 🙄 but amps very a little . It's just to light up three light bulbs . At 2amps each.
The parts? did they all came from the washing machine?
LG and some Kenmore (some models are basically rebranded LG)
Excelente....cuantas rpm recesita para producir 220v? O 120?
hola amigo vi tu projecto buenisimo saludos 5region chile
Hello amigo Aqui é do Brasil... faça uma ligação em Delta Ligue as às 36 bobina em série ligue o final do Fio Amarelo ligue no início do vermelho o final do vermelho ligue no início do segundo no início do azul e o final do azul ligue no início do Amarelo em cada uma Emenda sairá os três fios para a ponte retificadora...🔼(1 e 2) (2 e 3) 3 e 4) (4 e 5) (5 e1 em cada uma dessas emenda sai para a retificação