Design Failure into Something Usable! Making an Infinity Table!
HTML-код
- Опубликовано: 6 сен 2024
- My take on the Infinity table base design.
I've added some Tips and Tricks to making some nice MIG welds using the Mig Flux Stick and TIG Yes welder Mig 205DS multi process welder!
Evolution Chop Saw: amzn.to/3MqF18b
Surface Condition Tool (same as HF): amzn.to/3LYqzCR
YesWelder MIG 205: amzn.to/3nPPbFJ
Or get it here: yeswelder.com/...
Use code: MECHMASTER
Welding Supply:
Spatter Spray- amzn.to/403sStH
Nozzle gel- amzn.to/3ZLqNmg
Helmet- amzn.to/3JBQfVO
Gloves- amzn.to/3Jbw1kd
Angle Grinder- amzn.to/3mJe2Kt
Horizontal Band Saw: amzn.to/3JgdG5t
Magnets- amzn.to/3lcr5DQ
Clamps- amzn.to/3YF1xg9
Welding pliers- amzn.to/3Ta4lks
Wire Brush- amzn.to/3YOVuWu
Chipping Hammer- amzn.to/3Fp357h
Sorry no Harbor Freight welder for this weeks video!
I love how it ended up looking. Thanks for watching! 👍👍
Very explicit video, and probably one of the most helpful guide for making frames. However, for this particular design may be limited to stools since its support is more of a cantilever. That is why there was need to add the less fancy supports that arguably reduce the outlook.
Agree and thanks!
Exelente trabajo amigo👏👏👏👏 me podrías decir la medidas de los caños daludos d Argentina
I could of sworn you read my mind. I was thinking on how you made your welding table. Than you said you were making a video. Do you have any recommendations on where the best place to get your metal from
I just get it from a local supplier. Just google "steel near me" and start calling around!
@@-DIYPRO- have you had much experience between a saw like yours versus a bandsaw
Why not make the top parts run to the outer edge? Pieces 10, 11, 12, 13.
Butchers block table on the layer below the top frame (bolted from underneath so you can't see the fasteners with a glass top!
Good job, I noticed that the handle on your surface conditioning tool is backwards, it should curve over the drum to minimize bouncing.
If the supporting rods could be made more unnoticeable 🤔 but so far , great work ...I love the insight
Great video. Just finishing up one. Gonna do end tables next.
I found that piece 4 and 5 are the wrong way around in your table at 40 seconds. Also piece 9, 13, 14 and 18. I think pieces 4 and 13 should be 15. I think pieces 5, 9,14 and 18 should be 14.
Excellent workmanship. Thanks for the video.
Great work, what is the thickness of the square tubing?
I think it was either 12 or 14 gauge.
a bended rod to a quarter i think is much better than just a straight rod support, just my opinion but very nice work
Right on, thanks!
So without those extra bits of bar welded in, its too wobbly and unstable?
Exactly, will work as a piece of art but not if you want any weight on it.
Amigo excelente trabajo, felicitaciones
Dude!!! That table base is incredible! That’s seriously a piece of art! 😮
Thanks Go Dad!
Do you need special spray paint for metal?
Very good work,,👍👍👍
Thanks 👍
good 👍
Thanks
nice
Thanks!
How much did you spend on making that table?
$40 in in the tubing, $15 in paint. I only have an old table top on it now, haven't made the glass purchase yet. Still trying to find one at a thrift store. Just over $50 so far.
@@-DIYPRO- if it was mine I would make a top river table with LEDs
@@-DIYPRO- where did you buy your steel at?
What is the size of the tubular??
Very cool!
I would consider pouring some concrete inside tubes
That would be heavy duty!
Measurement