This week's project was to retrofit our DIY Radio Remote Control Hydraulic Kit to an older model Isuzu Tilt Tray Truck used for Towing, Transport, and Vehicle Recovery. This DIY kit will Greatly Increase Operator Safety and to also increase efficiency by 20% during loading and unloading procedures.
Great setup! Starting this process to retrofit a 1995 palfinger knuckleboom crane. any advice on determining compatibility of the pneumatic actuator with my valve block?
@@Hydraulic.Online Hi, I'm in north carolina, USA. It's a palfinger PK8000a knuckleboom. Best I can tell, the palfinger part number for the directional control valves is EV 313Z.
Wow ? We have sold quite a few kits all of them custom designed and assebled to suit the truck builder.s requirements. $20,000 is not just for the remote control Our remote kits Start at AU$938 $20,000 will get you all the hydraulic parts below including radio remote control Air solenoid operated Power take off with in-cab controls pic no. 4. High Flow Powe take off hydraulic Pump for fast operation pic no. 4. Chassis mounted oil tank with return line filter pic no. 5. High flow 5 lever flow control valve with self-centering controls & air/electric solenoids (3 remote controlled, 2 manual for car cradle) pic no. 11. 15,000lb Winch Hydraulic drive with planetary reduction box with manual free spool, front roller, and 20mtrs high tensile wire cable with swivel hook pic no. 3. 3.5m stroke heavy-duty slide cylinder (Custom built to suit your requirements), 3.5” bore, 1-3/4” rod pic no. 1. 24” stoke Tray tilt cylinders, 2.5” bore, 1.5” rod pic no. 8. Two Rear Lift Cradle Cylinders 2.5” bore, 1.5” rod, 14” stoke pic no. 9 One Rear Cradle slide Cylinder 2.5” bore, 1.5” rod, 48” stoke pic no. 2 4 x Safety Over centre/counterbalance valves (fitted with hard pipes is an extra cost) Remote control for tray including winch, tilt, and slide. pic no. 10 (Optional Australian made Radio Remote controls also available ) 20 Metres of 5,000 psi working pressure hydraulic hose pic no.13 Field fit reusable hydraulic hose tails, and adaptors for valve cylinders, pic no. 12 Plastic Cable/Hose carrier 3 meters long , 35mm High x 73mm Wide Cable Chain pic no, 7
This week's project was to retrofit our DIY Radio Remote Control Hydraulic Kit to an older model Isuzu Tilt Tray Truck used for Towing, Transport, and Vehicle Recovery.
This DIY kit will Greatly Increase Operator Safety and to also increase efficiency by 20% during loading and unloading procedures.
Nice work and good channel colleagues.
Thankyou very much for your kind words.
Great setup!
Starting this process to retrofit a 1995 palfinger knuckleboom crane. any advice on determining compatibility of the pneumatic actuator with my valve block?
We may be able to help, or at least point you in the right direction,.... Where in the world are you located Mr Voltrino?
@@Hydraulic.Online Hi, I'm in north carolina, USA. It's a palfinger PK8000a knuckleboom. Best I can tell, the palfinger part number for the directional control valves is EV 313Z.
20,000 for the kit ?wow😅
Wow ?
We have sold quite a few kits all of them custom designed and assebled to suit the truck builder.s requirements.
$20,000 is not just for the remote control
Our remote kits Start at AU$938
$20,000 will get you all the hydraulic parts below including radio remote control
Air solenoid operated Power take off with in-cab controls pic no. 4.
High Flow Powe take off hydraulic Pump for fast operation pic no. 4.
Chassis mounted oil tank with return line filter pic no. 5.
High flow 5 lever flow control valve with self-centering controls & air/electric solenoids
(3 remote controlled, 2 manual for car cradle) pic no. 11.
15,000lb Winch Hydraulic drive with planetary reduction box with manual free spool, front roller, and 20mtrs high tensile wire cable with swivel hook pic no. 3.
3.5m stroke heavy-duty slide cylinder (Custom built to suit your requirements), 3.5” bore, 1-3/4” rod pic no. 1.
24” stoke Tray tilt cylinders, 2.5” bore, 1.5” rod pic no. 8.
Two Rear Lift Cradle Cylinders 2.5” bore, 1.5” rod, 14” stoke pic no. 9
One Rear Cradle slide Cylinder 2.5” bore, 1.5” rod, 48” stoke pic no. 2
4 x Safety Over centre/counterbalance valves (fitted with hard pipes is an extra cost)
Remote control for tray including winch, tilt, and slide. pic no. 10 (Optional Australian made Radio Remote controls also available )
20 Metres of 5,000 psi working pressure hydraulic hose pic no.13
Field fit reusable hydraulic hose tails, and adaptors for valve cylinders, pic no. 12
Plastic Cable/Hose carrier 3 meters long , 35mm High x 73mm Wide Cable Chain pic no, 7