I followed your instructions and picked what I thought was the latest 10 channel firmware mod but when I installed it, the version was older than the version you show. The update I downloaded was the same file size but ended up being dated 3/12/15 21:34. The list on the update page is not quite clear as to the actual dates on the files. Can you please point me towards the same update you used here? I and probably a lot of others would be grateful. Thanks for the good instruction vid too!
Great video mate! I see everyone using those jst pins pffff glad you showed me the easy way. So my question if I want to use Ibus on my FS-I6 transmitter do I need to have it updated because now I only am able to choose ppm!? So in order to use Ibus I need this update?
I downloaded what I thought was the latest FlySky firmware update from the link you supplied. I downloaded the one called "Firmwares House cleaning" and finally got it to install but it looks like I downgraded from a 2015 version to a 2014 version. I am not really interested in the 10 channel mod but I am looking for the latest "OEM" version if there is one. Can you direct me to it if there is a newer version? The only reason I am looking for a newer version is so I can use my FS-i6 to fly the "DRL" racing simulator. It will only work with the latest firmware. Thanks!
Hi. Good video . I like my FS I6 update do I need to set anything back from my current model or will they all kept? I have a 6 -channel receiver , it is better to replace that to a 10 channel so I don' t have to use the I-bus ? Thanks for your reply. Sincerely , Henk
I re-binded the rx&tx but now nothing is happening in receiver tab in CF. So I factory reset & still no input. Both bound but the naze does not seem to be picking up input from the rx & I can't setup modes either. It was working before the 10ch mod but not even changed any wires, reverted back to factory reset. Set everything up again but no response from the bound tx, rx on the receiver tab. HELP. So I would not do this unless you know what you are doing.
Hi , thanks for video. i tried same way for many time but uploading new version stops at 1% of 3%...it doesnt continue till 100%... do you have any idea for this issue?
+Eric Nordstrom if your using the FlySky FS-R9B 8ch non telemetry receiver it uses AFHDS and the transmitter has to be set to (AFHDS)(or AFHDS 2A OFF). If your using the FS-iA6B 6ch or the FS-iA10 10ch they both have telemetry(AFHDS 2A) and have a I-Bus port (I-Bus supports more channels up to 14ch), Im using the FS-IA6B with I-Bus to a I-Bus-to-PPM to my APM 2.6 giving me 10ch. This video helped me with that part. ruclips.net/video/ag-2fymYpYc/видео.html
hi mate, could u post the link where u downloaded the firmware and the version of the windows, i.e. windows 7, 8, 10 that u are using? I downloaded one but it doesn't work even if I just ran the firmware on my windows, it did not start to run. I don't know what the problem was that. Please help me to solve it. thanks
why cant my PC see my TX?? i have same cable and installed drivers... but i cant seem to connect. "device is not connected" is says.... i open the correct port to the cable but doesnt see my TX... any ideas??
I have the same issue , The usb adapter doesnt seem to work like he shows in this video. I am going to be trying with an arduino, which seems like the more popular way to do this.
Alex Babuca I just got mine but not sure how to use it and it didn't come with any wires to connect it and a device.... not sure if we can use any kind of wire and solder to it that way...?
You dont have to solder anything with the arduino. You just need some small wire you can use something like ethernet cable take 3 cables and strip the ends(it would help it it was a solid wire) and wire it up like this www.rcgroups.com/forums/showthread.php?2424147-How-to-update-FS-i6-TGY-i6-with-Arduino
I'm using an original update cable and doing everything as intructed everyday for a few months. everytime getting the same thing where it says no connection. help?
Aryan Gangurde 1) you must install the driver of the cable and check weather it is connected in device administration and com port also 2) I am also using the original cable check weather the cable is working or not by line tester wires must be broken in my case wires were broken so I bought a new connecter and soldered it and it's done comment for further help
please can you tell me if this cable www.banggood.com/22-in-1-RC-Flight-Simulator-Cable-for-Realflight-G7-G6-G5-G4-p-950398.html?rmmds=myorder worked for you
The cable doesn't work. I bought one for upgrading. I can't find me either. So I just bought the chip for my last night. You have to get the chip and make the connection yourself. You have to get the chip as the link listed below: www.ebay.co.uk/itm/162338764341?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
Hi guys, I can only flash the recovery 6ch ( github.com/benb0jangles/FlySky-i6-Mod-/blob/master/Mod_i6_Alt_Recovery_Programmer_V1_0/Mod%20i6%20alt_recovery%20updater%20v1_0.exe) and the NovaX 8 channel ( github.com/benb0jangles/FlySky-i6-Mod-/blob/master/Firmwares/RcLogger%20Original%20Firmware/RCLogger-NovaX350-Original-Firmware.exe) firmwares on my FS-i6. Any else and the updater gets stuck on 0% percent. I have tried on windows 7, 8. Can somebody please help me on this matter as trying to get the 10ch mod to work. Thank you
spot on instructions, thank you. Now I have 10 channels - just what the doctor ordered :)
Thanks, great vid. This worked 1st time perfect.
I followed your instructions and picked what I thought was the latest 10 channel firmware mod but when I installed it, the version was older than the version you show. The update I downloaded was the same file size but ended up being dated 3/12/15 21:34. The list on the update page is not quite clear as to the actual dates on the files. Can you please point me towards the same update you used here? I and probably a lot of others would be grateful. Thanks for the good instruction vid too!
This worked so far, I have ten channels. I just need to bind my tx to the rx's after work tnite. Fingers crossed.
Great video mate! I see everyone using those jst pins pffff glad you showed me the easy way. So my question if I want to use Ibus on my FS-I6 transmitter do I need to have it updated because now I only am able to choose ppm!? So in order to use Ibus I need this update?
I downloaded what I thought was the latest FlySky firmware update from the link you supplied. I downloaded the one called "Firmwares House cleaning" and finally got it to install but it looks like I downgraded from a 2015 version to a 2014 version. I am not really interested in the 10 channel mod but I am looking for the latest "OEM" version if there is one. Can you direct me to it if there is a newer version? The only reason I am looking for a newer version is so I can use my FS-i6 to fly the "DRL" racing simulator. It will only work with the latest firmware. Thanks!
Hi. Good video . I like my FS I6 update do I need to set anything back from my current model or will they all kept?
I have a 6 -channel receiver , it is better to replace that to a 10 channel so I don' t have to use the I-bus ? Thanks for your reply. Sincerely , Henk
I re-binded the rx&tx but now nothing is happening in receiver tab in CF. So I factory reset & still no input. Both bound but the naze does not seem to be picking up input from the rx & I can't setup modes either. It was working before the 10ch mod but not even changed any wires, reverted back to factory reset. Set everything up again but no response from the bound tx, rx on the receiver tab. HELP. So I would not do this unless you know what you are doing.
what is the latest as of.now? mine is running March 2015. should I update?
I just was doing the steps but when I plug my i6 in it says my i6 is port COM14. on the mod programm there's only COM1-8. Can someone help?
Can you also provide the link from where you got please....
with this update can i use the Flysky FS-IA10B (10ch Receiver) ???
will it still work with older RX fs-i6A after the update? Reason for this question is, I don't want it to be scrapped and thrown away.
I cant find a com port. I also installed the necessary drivers. But, I can identify the controller as a game controller.(PPM) Need help!
I'm using the FS-IA6 receiver. Do I have to have a different receiver to use the 10 channels?thx
Thankyou sir...
Hi , thanks for video. i tried same way for many time but uploading new version stops at 1% of 3%...it doesnt continue till 100%... do you have any idea for this issue?
after you get access to all 10 channels how do you use them? I've tryed binding to a flysky 8 channel receiver and I can't get it to bind.
+Eric Nordstrom if your using the FlySky FS-R9B 8ch non telemetry receiver it uses AFHDS and the transmitter has to be set to (AFHDS)(or AFHDS 2A OFF). If your using the FS-iA6B 6ch or the FS-iA10 10ch they both have telemetry(AFHDS 2A) and have a I-Bus port (I-Bus supports more channels up to 14ch), Im using the FS-IA6B with I-Bus to a I-Bus-to-PPM to my APM 2.6 giving me 10ch. This video helped me with that part. ruclips.net/video/ag-2fymYpYc/видео.html
Did you forget to put the signal key in first before powering the rx. Otherwise it will not bind.
i never put this cable in rx....bus its work... you now if i have less range or lost eazy the signal?
I have a problem when you shut eachine i6 ( flysky fs - i6 ) after updating to flysky fs- i6 can not I run
Help me i want to connect ibus to pixhawk but there is no ibus in pixhawk . There is only ppm , sbus . Tell me how can i connect ibus to pixhawk ??
hi mate, could u post the link where u downloaded the firmware and the version of the windows, i.e. windows 7, 8, 10 that u are using? I downloaded one but it doesn't work even if I just ran the firmware on my windows, it did not start to run. I don't know what the problem was that. Please help me to solve it. thanks
bro I have a problem after updating it says keep the thortell and switches in the normal positions and not starting up after many tries
its just an s-video cable right?
why cant my PC see my TX?? i have same cable and installed drivers... but i cant seem to connect. "device is not connected" is says.... i open the correct port to the cable but doesnt see my TX... any ideas??
I have the same issue , The usb adapter doesnt seem to work like he shows in this video. I am going to be trying with an arduino, which seems like the more popular way to do this.
Alex Babuca I just got mine but not sure how to use it and it didn't come with any wires to connect it and a device.... not sure if we can use any kind of wire and solder to it that way...?
You dont have to solder anything with the arduino. You just need some small wire you can use something like ethernet cable take 3 cables and strip the ends(it would help it it was a solid wire) and wire it up like this www.rcgroups.com/forums/showthread.php?2424147-How-to-update-FS-i6-TGY-i6-with-Arduino
Wann Sklobi try on another computer borrow one if you have to just try to eliminate things to find the solution
I tried using the usb dongle like you have in your video in 3 different computers (2 win 10 , and a win 7) and it never picked up a com port
I'm using an original update cable and doing everything as intructed everyday for a few months. everytime getting the same thing where it says no connection. help?
Aryan Gangurde
1) you must install the driver of the cable and check weather it is connected in device administration and com port also
2) I am also using the original cable check weather the cable is working or not by line tester wires must be broken in my case wires were broken so I bought a new connecter and soldered it and it's done
comment for further help
Hello, is it possible to use dongle usb simulator to update it?
has anyone successfully performed this update using a Mac OSX and the included serial to USB cable?
You Can tell if this cable can be used with the Simulator? I Tried but i can't do that, Please help me Friend!
this cable is not working with simulators unfortunately
If using windows, in search - setup USB game controller, and then calibrate it. Good to go.
i need upgrad firmware of flysky fs-t6 how i find it
when i did it my transmitter no longer works it wot turn on
Where did you get the original turnigy firmware?
kevin Unknown
github.com/benb0jangles/FlySky-i6-Mod-/tree/master/Firmwares
Can you use that cord for Aerofly RC 7?
please can you tell me if this cable www.banggood.com/22-in-1-RC-Flight-Simulator-Cable-for-Realflight-G7-G6-G5-G4-p-950398.html?rmmds=myorder worked for you
hey.. 🙏does anyone try in factory mod chage frecuncyi try but i canot save pls help
thanks bro 😎 and btw it will wipe your settings 😂
where can I download firmware?
+Honza Kosák github.com/benb0jangles/FlySky-i6-Mod-
The cable doesn't work. I bought one for upgrading. I can't find me either. So I just bought the chip for my last night. You have to get the chip and make the connection yourself.
You have to get the chip as the link listed below:
www.ebay.co.uk/itm/162338764341?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
I'm sorry I was able to play a eachine i6 to flysky fs - i6
with this update can i use the Flysky FS-IA10B (10ch Receiver) ???
eachine i6 not connetted device problem
Hi guys, I can only flash the recovery 6ch ( github.com/benb0jangles/FlySky-i6-Mod-/blob/master/Mod_i6_Alt_Recovery_Programmer_V1_0/Mod%20i6%20alt_recovery%20updater%20v1_0.exe) and the NovaX 8 channel ( github.com/benb0jangles/FlySky-i6-Mod-/blob/master/Firmwares/RcLogger%20Original%20Firmware/RCLogger-NovaX350-Original-Firmware.exe) firmwares on my FS-i6. Any else and the updater gets stuck on 0% percent. I have tried on windows 7, 8. Can somebody please help me on this matter as trying to get the 10ch mod to work. Thank you
are you taking it back to the first skyfly firmware for everyone so that it is a clean set up on every try?
Hi, i've got the simulator cable - that has 4 switches for each simulator. Can I use this instead of this update cable, which i dont have?
lagz89 don't know never tried it, The banggoods cable you can order does work for sure