Always worth checking the centre bearing on prop shaft it causes a similar issue if worn or the rubber mount has perished. I just changed my prop shaft it cured it.
You posted a video and now everybody asking you questions! It’s not cool to ignored those whom really need your help with the same issues like myself!!
what kind of scanner you used and where is the steering wheel sensor can you pleas film it or if you close by i'll take my rl3 to you to fix it i'm in Brooklyn tank you for posting
Hey john, what city are you located in? I have a transmission fault on my 06 ldr. When I shift it in gear it comes out of gear. Not sure what's wrong with it or what to do!!! Please help
Fettyseye1 - same issue. My 2008 Range Rover Sport Winchester model. Just bought it used from a dealer and they won’t cover any issues. Sure would like to know if there is a way to address without paying dealer repair.
Im sure the OP must have fixed or sold the car by now, but for others having this problem - Replace your shift linkage. Search on RUclips, you'll find some videos on how to do it.
LedAutomaticos L10 Oi amigo tudo bom eu sou mohsen do irã eu também tenho mesmo problema sobre meu carro Lr3 Ele está falando que carro dele não vai achar marcha 2 para 3 Também para torcer marcha 3 para 4 também tem problema! Ele está explicando sobre como pode arrumar esse problema! Minha língua portuguesa não é muito bom mas eu posso intender inglês muito bom!
Need help I have Range Rover 2004 vogue The problem is that when I start car after firest gear it’s like stuck then two three times same problem Some times it’s fine working everything Or when I press break speed low down like fealing stuking As per machnic I change double gear Moter Transmission oil change Shaft change He fixed throw computer also but problems same Any one help me for this Thank you so much appreciated
Hello, the Land Rover I own has an issue similar to this. The Rover would rev at gear 3 and when I accelerate it would jump getting to gear 4. I would like to try the steering wheel sensor calibration out, however I'm not sure how much a person should charge to get that job done or even where I would be able to get it done. Thank you.
You need a Bi- directional scanner. You can do special and functional test with these high- end scan tools. I like the Verus Pro scanner by Snap On Tools. Its a professional level scan tool. Its not cheap- but worth the money.
Always worth checking the centre bearing on prop shaft it causes a similar issue if worn or the rubber mount has perished. I just changed my prop shaft it cured it.
The 3 amigos. 230k miles makes me happy to keep my 06 RR HSE.
What’s the name of the tool?
@@TheRealMrToxic usually a decent obd2 scan tool has a calibration option.
For those asking about how to do the steering angle calibration: get the e tool that does such tasks and follow the instructions on the screen.
What’s the name and brand of the tool?
You posted a video and now everybody asking you questions! It’s not cool to ignored those whom really need your help with the same issues like myself!!
Lol! He might be ill or something. Never know!
My 08 Range Rover has shift problem too,wonder how to reset the steering angle sensor?
How did u fix it ? I have it now
@@aymenem5304 I didn’t fix but it backed to normal itself,
What’s the name of the machine you used to reset the wheel calibration?
what kind of scanner you used and where is the steering wheel sensor can you pleas film it or if you close by i'll take my rl3 to you to fix it i'm in Brooklyn tank you for posting
I have a 2006 supercharged it does not shift rpms go all the way up. says gears may be limited faulty transmission
My 1996 Range Rover starts and runs good it's when I shift to gear the transmission doesn't respond. what could the problem be?
Hi mate did you figure it out I'm haveing same problem
Hey john, what city are you located in? I have a transmission fault on my 06 ldr. When I shift it in gear it comes out of gear. Not sure what's wrong with it or what to do!!! Please help
Fettyseye1 - same issue. My 2008 Range Rover Sport Winchester model. Just bought it used from a dealer and they won’t cover any issues. Sure would like to know if there is a way to address without paying dealer repair.
Im sure the OP must have fixed or sold the car by now, but for others having this problem - Replace your shift linkage. Search on RUclips, you'll find some videos on how to do it.
@@any0n378 how much would it cost.. roughly. I want to see how bad my mechanic ripped me off 😂🤣
@@fettyseye1127 People who can't or don't want to hunt, should not complain about the price a hunter charges to get them some meat.
@@any0n378 I took it to a place that only works on LR'S,was recommended. They did good work I was just wondering about the estimated cost
Can this shift late problem be caused by new break rosters and pad to be installed?
For a 2005 lr3
Unlikely, but if the ABS sensors were disconnected/damaged it is theoretically possible. You should have an ABS warning light on if they were damaged.
what is the problem,how to solve it?
Im from Brazil do not speak inglish
you can legend of Spanish thanks for vídeo
LedAutomaticos L10
Oi amigo tudo bom eu sou mohsen do irã eu também tenho mesmo problema sobre meu carro Lr3
Ele está falando que carro dele não vai achar marcha 2 para 3
Também para torcer marcha 3 para 4 também tem problema!
Ele está explicando sobre como pode arrumar esse problema!
Minha língua portuguesa não é muito bom mas eu posso intender inglês muito bom!
Need help
I have Range Rover 2004 vogue
The problem is that when I start car after firest gear it’s like stuck then two three times same problem
Some times it’s fine working everything
Or when I press break speed low down like fealing stuking
As per machnic I change double gear Moter
Transmission oil change
Shaft change
He fixed throw computer also but problems same
Any one help me for this
Thank you so much appreciated
Hi dear I have 2005 range please help me
This vehicle needed a reset, You may need to have yours diagnosed first
Hello, the Land Rover I own has an issue similar to this. The Rover would rev at gear 3 and when I accelerate it would jump getting to gear 4. I would like to try the steering wheel sensor calibration out, however I'm not sure how much a person should charge to get that job done or even where I would be able to get it done. Thank you.
The exact same thing with my lovely trick 2006rangerover
Anyone know how to work on a landrover2006 tramisom
i have same problem, what scanner do you use and where can i get the scanner?
Snap on and you're looking at around 800-1000 dollars for the scan tool........ Used. New is about 3-5k Dollars.
@@fernandomoreno3572 dam.....any scanner wont due??
@@myathletesbody any scanner will give you codes. But to get into the brains of the computer you will need a more high tech scanner.
You need a Bi- directional scanner. You can do special and functional test with these high- end scan tools.
I like the Verus Pro scanner by Snap On Tools. Its a professional level scan tool.
Its not cheap- but worth the money.
No change Automatic gear
That condition can be caused by a lot of different things. I would have it diagnosed and scanned for troiuble code
* drags screw driver across clear plastic