I followed this and it worked ! Thank you! I pocked the silicone with paper clips and touched the contact points instead of removing the board and soldering
Wow Epic, I am about to do the same to a ninebot G30P because they want me to "register before enabling full capacity"....ScrewThem... This was not mentioned on their product's box. Either they enable full capacity or I sue them for selling me an undercapacity product. Alternatively I'll write my own firmware config file and load it in, thank you for showing how to do this :) 15 minutes on RUclips is certainly greater than 4h on hold with their help line which I never got through to... I will let you know how it goes, may take a week with how busy I am at work though and not set up to run Windows machines at the moment.
Hello, I have a NIne bot max g30D scooter. Is this procedure enough to make you use the maximum power or will you still need dashboard firmware? And one more question: is it possible to change the serial number without a computer?
I need help please I tried to flash a custom firmware and now I'm stuck at 12 mph no matter what firmware I try I'm stuck at that if I replace the controller completely would it take me back to stock 18 mph?
It depends on if you installed ble o esc. If esc then you need to do like this. Dashboard won't help if you have installed wrong esc firmware becus it's inside controller.
Can not connect to target! I flashed it once and everything was fine, the second time I insert the programmer and here is such an error, I don’t understand anything, how to solve the problem?
Hello I started to mess around with my controller because I want to instal a relay. Long story shor I think I messed it up. I made a stupid mistake trying to check the display voltage with a multimeter. Anyways the display port sparked from the multimeters. After I plugged everything back my display won’t turn on . The only thing that happens the controller flashes green and brake lights flashes
Hi! Unfortunately, the given links are not working! can you help me update the links? I have a G30 scooter and it is limited to 20 km/h! Germany has been brought to Ro! the speed limit here is 25 km/h! I wish I could flash it again! Thank you for your quick answer!
@@orosziroland9961 hi. Yes i have taken down because new version controller is out and will get locked if you use old files. Best way is to shfw after sr link. Do not use files.
Try this firmware. Its Police mode on so you have to hold down the break when start scooter to activate the full speed. I guess you have a gen 2 motor. linksharing.samsungcloud.com/bekjvaK9MPBq
@@WattsnabbAB yes its stock controller , i didn't do the flashing just added the external 12v battery in pararel , ive been trying every fw with no luck maybe your my savior
Hi, I have a g30 Europe and it has the old type with the 3 connection's on the front of the bms. On your video you connected to a 5v once you connected the 3 connections. Where on my old bms can I get the 5v from?
Hi. That is not bms so you dont mistake bms firmware. Its controller. You can connect dashboard cable to controller and look at it. There you have a red cable witch is 5v to dashboard. Disconnect it and you know where 5v on board is :)
How can I get in touch with you to mail my piece. I don’t wanna do all this shit I might break it and I can’t stand how slow my g30 max goes right now?.
Jag köpte ninebot GD30 Max för 4 månader sen typ, kan jag inte ändra region och därmed hastighet på ett enklare sätt? Den där operationen vågar jag mig inte på.
Jo som jag säger i videon så är bara denna till för om man låst sitt moderkort. Annars använder man xiaoflasher eller scooterhacking utility för o ändra. Finns videos på youtube för o göra de. Så denna video är endast till för de som låst sin scooter så den är okörbar.
I have a Ninebot G30D. I changed the region to US G30LP comes to only up to 27 km/h without weight, with weight it comes to max 24 km/h. When you go uphill, it reaches a maximum of 10 km/h. What am I doing wrong?
Can someone give me link to new firmware to flash sn 2.0 that was previously rental scooter? Got one from sale local but need all firmware for flashing orignal dash and controller please!! I have st linkv2 just help me get up to date installs please
@@dark-fallen5569 you can always try but need tonhave a good connection in order to st link. Even when o solder the st link dont get good connection so you need to insure you have a good connection. Look at my latest video there I show how it's done on the front of the controller but you need to solder then. And have a microscope, grinding pen and a good solder iron tip.
Hello, I purchased a couple Ninebot Max G30 SNSC 2.0 from a police auction and I am trying to find some information on flashing etc. to drive it. Can you help??
@@WattsnabbAB So everything is original but removed the GPS unit?? I tried connecting with Xiao but no luck. Bluetooth does not light up on dashboard at all??
@@mikerak7473 the snsc have a locked dashboard so you need a "normal" original dashboard to flash. Or st link the dashboard you have so you get original ble in it.
Actually asked that if that was possible in a FB group recently. I jailbraked my iphone once, and it bricked it. Dont want that to happen to my even more expencive scooter. Is it a high risk of bricking?
@@willynordboe5853 no but you have to dig deep into how its done and really understand what you doing. Some just flash just by looking in one video and often they flash a es o xiaomi program in the max. :)
hello friends in Indonesia there is a lot of scoter waste maybe because of regulations so it's not allowed on the highway I found a scoter in used goods of the MAX G30 type, can it be turned on after I charge it
66 hours of life but there is a code 32 key symbol, is the system program in the controller or can it be flashed or should I just change the controller, please guide, thank you
Hello I bought a second hand ninebot g30 max to be able to go to my heart appointments. When I tested the scooter it went up to 20 mph. The guy unbinded his account. I went home to charge it and when I went to drive the scooter it only went 13 mph. I noticed that the region was changed to DE and I'm trying to put it to region U.S. I Also noticed that the esc is 1.8.8. It's saying I have to downgrade to be able to switch region to U.S. can you please help me change it to REGION U.S.
Hi. Yes you can send in ypure controller and we can st link it. We charge 35us plus shipping to sweden. Maybe you have a repairshop that can help you in youre country.
@@WattsnabbAB do you have the esc version before the update of 1.8.8 version? If you have the zip file for the previous esc version. I could try to downgrade it and then I'll be able to switch the region back to U.S. please let me know if you can provide me the esc version before the 1.8.8 update. Thank you.
@@gerrellpadua8873 yes that what we sell. www.wattsnabb.se/products/ninebot-g30-max-modellerna/reservdelar-till-ninebot-g30-max-modellerna/original-ninebot-g30-g30d-max-moderkort-kontrollkort
I would forst try with diffrend charger( you have to connections in the bike). Then I would measure if the voltage reache the bms with a multimeter. Can be the charger inside that is broken.
HELLO, I HAVE A PROBLEM. AFTER I APPLIED ALL THE STEPS FROM THE VIDEO, CHANGED THE SERIAL NUMBER AND CHECKED IF HE REALLY CHANGED IT. I TRIED IT AND SPINNED IT AT 30 KM / H. WHEN I CLOSED IT AGAIN AND TRIED TO STAND ON IT, IT SHOWS AN ERROR 10
Ok tjen you have done something wrong error 10 is wrong firmware on controller. Try to solider the controller and reflash it. Before fixing the serial and cfw try to see so it work.
Please help me I followed all the steps and it was successful but when accelerating it does not work it runs if I turn on the dash if it gives me a connection with the app but when pressing the accelerator it does not walk any idea help me please
Hi. Was that the problem before you did the steps? You can have damaged you mosfet or it can be somthing else wrong. Can even be somthing with the throttle. It's hard to say. What you can start to do I measure your mosfet to see that they are good. Then change the throttle. But can even be that some cables are not connected well. So try to check them to. Do you see you're battery on dashboard? Do somthing looks strange there?
I changed the region on my G30D and after this it stopped displaying battery percent while charging, it is charging but nothing is displayed and the lights are also not indicating that its charging. If I set the region back to D this will fix the problem, does anyone know how to fix this?
Hi do you accept if i send you my controller and ship it back to me?i will pay the work and the cost.i just need to unlock the speed for me to enjoy it going to work
@@AlexfreDholm i live in california and yes it is new i dont know what to do i tried contacting the company and they send me to leave a message on the phone then after i leave it with my information to contact me back they never do!
That sounds like a great video!! Will do it when i get my g30. This was a costumer that got locked out of his g30d when he tried to flash it with Bluetooth.
I need stock firmware for my new max g30 d2.. i flashed my new Scooter a few times and i get all sorts of wierd behaviour now, headlight always on and max speed 20kmh atm 🤣
@@WattsnabbAB lyckades inte så bra med min förra custom firmware tyvärr.. fick den att frivarva 30 men den hade inget vrid och orkade knappa 20?vet inte riktigt vad jag gjorde för fel men misstänker att de blev nå vajsing med region eller nåt?` har du möjligen en länk till en färdig fil?
@@WattsnabbAB jag har flashat denna filen nu, bara kört på sport. gjorde 25kmh igen precis som jag ville, och känns betydligt starkare än orginal? kommer det påverka räckvidden nämnvärt? mvh Tommie
@@WattsnabbAB vafan nu tar den inte laddning ju :( EDIT: verkar bara vara så att den inte längre visar att den laddar. för kan se att den ökar i ninebot appen. skulle va najs att få tillbaka det som den var :)
@@WattsnabbAB i just bought mymaxmods 48v external kit, cant flash because my firmware is to new, dont have a windows laptop maybe you could sell me a pree flashed controller ??
@@sandmhoder yes sure. Have them here. You can send me firmware and ordet with costume firmware and I will send pree flasher controller with the firmware you want. Chose: med costume firmware. www.wattsnabb.se/products/ninebot-g30-max-modellerna/reservdelar-till-ninebot-g30-max-modellerna/original-ninebot-g30-g30d-max-moderkort-kontrollkort
I followed this and it worked ! Thank you! I pocked the silicone with paper clips and touched the contact points instead of removing the board and soldering
Great job :)
@thanosd6885 can you tell where they are on the front?
@@hardstylefreaak hi already have a video on that
@@WattsnabbAB cual es el link amigo?
@@andreweltecnologico8003 hi dont understand
Wow Epic, I am about to do the same to a ninebot G30P because they want me to "register before enabling full capacity"....ScrewThem... This was not mentioned on their product's box. Either they enable full capacity or I sue them for selling me an undercapacity product. Alternatively I'll write my own firmware config file and load it in, thank you for showing how to do this :) 15 minutes on RUclips is certainly greater than 4h on hold with their help line which I never got through to...
I will let you know how it goes, may take a week with how busy I am at work though and not set up to run Windows machines at the moment.
Alsoe I gotta buy new soldering iron tips, mine are like SO dead lol
Good luck but for full capacity you just need to change serial and install a costume firmware. :)
I have a G30P is this good for error 18
So, hello, you said that you will do so lot of things, and you said that you will write how it was, so... How it was?
It worked perfectly, thanks so much! (2021 G30LD)
The best video ever thks man really apreciated
By far working well thanks you, very helpful ^^
appreciate your work ,thanks man
Saved the day👍 bro😎
thank you very much. i love you!
No problem man. :)
Hello, I have a NIne bot max g30D scooter. Is this procedure enough to make you use the maximum power or will you still need dashboard firmware? And one more question: is it possible to change the serial number without a computer?
Hi. This is for unlock the scooter if its locked or have a firmware that lock it from flashing. You dont need to do anything with dashboard.
Yes if you have firmware lower the 1.7.0 then you can use scooterhacking utility
is it also with the drv 1.8.3?
@@WattsnabbAB
@Mister_Leon yes as long as you have same controller
@@WattsnabbAB hello, please say me, i have 1.7.14. is it a chance to use schooterchack?
I need help please I tried to flash a custom firmware and now I'm stuck at 12 mph no matter what firmware I try I'm stuck at that if I replace the controller completely would it take me back to stock 18 mph?
Great Video, so if the scooter is locked is it enough too just change the Dashboard or do i need too flash it like in the video. ?
It depends on if you installed ble o esc. If esc then you need to do like this. Dashboard won't help if you have installed wrong esc firmware becus it's inside controller.
@@WattsnabbAB whats ble ? how do i find out if its ble or esc ?
@@WattsnabbAB and what if i change controller ?
@@elchapogringo3695 ble = dashboard firmware
Esc= controller firmware.
All depends what you installed.
Are you still using the 45km/hr firmware? Any personal comments on the usage?
Witch do you mean?
Can not connect to target! I flashed it once and everything was fine, the second time I insert the programmer and here is such an error, I don’t understand anything, how to solve the problem?
Ethere you damage you're st link or bad connection somewhere.
@@WattsnabbAB everything is in order, I checked it many times, I could show you on video in telegram
@@A.G_369 i trust you done it right if you say so. Then it must be somthing wrong with st link or the controller.
@@WattsnabbAB ruclips.net/video/TSI_YMdmAzY/видео.html
Hello I started to mess around with my controller because I want to instal a relay.
Long story shor I think I messed it up. I made a stupid mistake trying to check the display voltage with a multimeter. Anyways the display port sparked from the multimeters. After I plugged everything back my display won’t turn on . The only thing that happens the controller flashes green and brake lights flashes
Sorry to here that. Why measure display port?
@@AlexfreDholm to check what voltage it runs on because I want to install a relay on it
I did the same fucking stupid mistake🤌
@@RideWithAnthony ok I understand but you could measure at the top of the dashboard. :) ok it's 5v for everyone that will try in the future
@@G30MaxForce sorry to here that!!
Hi! Unfortunately, the given links are not working! can you help me update the links? I have a G30 scooter and it is limited to 20 km/h! Germany has been brought to Ro! the speed limit here is 25 km/h! I wish I could flash it again! Thank you for your quick answer!
@@orosziroland9961 hi. Yes i have taken down because new version controller is out and will get locked if you use old files. Best way is to shfw after sr link. Do not use files.
Hi. I need ESC126 full dump to install with st link the link is not valid
Ok inhave a 48v mod on the scooter but im not going pass 44khm on the road what can i do to achieve full power ! And peak speed at 50khm freewheel
Try this firmware. Its Police mode on so you have to hold down the break when start scooter to activate the full speed.
I guess you have a gen 2 motor.
linksharing.samsungcloud.com/bekjvaK9MPBq
@@WattsnabbAB yes its stock controller , i didn't do the flashing just added the external 12v battery in pararel , ive been trying every fw with no luck maybe your my savior
@@flashunlokr hope you mean in series :) yes I hope so. The speed will depend how high you're 12v kit charge. My do 12,6v
@WattsnabbAB Hello. Pls tel me what version of boar layout do you have on the video? AA01 or AB02 ?
Hi, I have a g30 Europe and it has the old type with the 3 connection's on the front of the bms.
On your video you connected to a 5v once you connected the 3 connections. Where on my old bms can I get the 5v from?
Hi. That is not bms so you dont mistake bms firmware. Its controller. You can connect dashboard cable to controller and look at it. There you have a red cable witch is 5v to dashboard. Disconnect it and you know where 5v on board is :)
Thx !! 🎉
can you please send me the link of the st link? icv would like exactly the same with the same colors from the cables
Hi please helpdesk me,St _link v2 or v3 ?
can you link where you bought the St-link?
St link pins are still accesible from the same side. You really didn't notice that?
Dont know what you mean becuse its a d controller. They have pins on the back.
hi. i have problem with st link utinity. i have msg '' can not connect to target '' . verifiying the soldering all is ok .can you help
Hmm strange can't really help then. Try another controller and st link to see if the controller or st link is damaged
How can I get in touch with you to mail my piece. I don’t wanna do all this shit I might break it and I can’t stand how slow my g30 max goes right now?.
Hi sir, how do you know which is swdio, swdclk, etc.? I am trying to do this with G30 LE II and I'm not sure if it's the same as your's.
So the pattern are the same so if you find gnd with continity mode on multimeter then the rest is in order gnd, sweclk, swedio
ninebot flasher isnt finding anything, i tried on two different pc's, is there another way to change the serial etc ?
Yeah you can use scooterhacking utility om Android phone.
I have m365 board v3 and it has those pins but in vertical oriention and no markings.. Any ideas about order of those pins?
Mesure GND against minus and then order is GND , sweclk, swedio
Jag köpte ninebot GD30 Max för 4 månader sen typ, kan jag inte ändra region och därmed hastighet på ett enklare sätt? Den där operationen vågar jag mig inte på.
Jo som jag säger i videon så är bara denna till för om man låst sitt moderkort. Annars använder man xiaoflasher eller scooterhacking utility för o ändra. Finns videos på youtube för o göra de. Så denna video är endast till för de som låst sin scooter så den är okörbar.
@@WattsnabbAB Ah ok jag lyssnade med med full koncentration men tack då vet jag hur det ligger till.
I have a Ninebot G30D. I changed the region to US G30LP comes to only up to 27 km/h without weight, with weight it comes to max 24 km/h. When you go uphill, it reaches a maximum of 10 km/h. What am I doing wrong?
What tiers pressure do you have?
hello, you should flash drv 126 from scooterhacking utility and be sure to have the right US serial number as they show in SHU
Can someone give me link to new firmware to flash sn 2.0 that was previously rental scooter? Got one from sale local but need all firmware for flashing orignal dash and controller please!! I have st linkv2 just help me get up to date installs please
Can it be done without soldering? Is it also feasible in the old controller? I have the scooter locked by the firmware :(
Can I use duct tape on the pins?
@@dark-fallen5569 you can always try but need tonhave a good connection in order to st link. Even when o solder the st link dont get good connection so you need to insure you have a good connection. Look at my latest video there I show how it's done on the front of the controller but you need to solder then. And have a microscope, grinding pen and a good solder iron tip.
Hi, i have a ninebot max i've changed the dashboard and the controller, the problem is that i can not turn off the scooter nor change between modes.
Hi. Sounds like you dashboard buttom is broken but can't say for sure. Try you're old dashboard if it works.
Ser bra ut!
Please Show how to Upgrade fets. I have one Phase burned..Need to replace fets..
Does the controller contain the original serial number or is is stored in the stem piece?
Its in the controller
Thank you sir. Can I swap controller with a new one without issues. Thanks 🙏
@@jgarcia690 yes
Hello, I purchased a couple Ninebot Max G30 SNSC 2.0 from a police auction and I am trying to find some information on flashing etc. to drive it. Can you help??
What you need to flash? If controller use xiaoflasher. Easy and fast. You need a original dashboard.
@@WattsnabbAB So everything is original but removed the GPS unit?? I tried connecting with Xiao but no luck. Bluetooth does not light up on dashboard at all??
@@mikerak7473 the snsc have a locked dashboard so you need a "normal" original dashboard to flash. Or st link the dashboard you have so you get original ble in it.
What are the specs with the original G30 controller? I want to use a new motor !
What do you mean?
Hi it work on G30DII Audi ?Same motherboard like video or older ?
Hi. There is a easere method now. But need to do a video about it.
@@WattsnabbAB Hi, soon i will order the st link and open the lid for the first time. Is it worth waiting for your explanation?
@gagash3683 look at my latest video there you will see easiest way to do this :)
@@WattsnabbAB Thank you :D
maby im off here, but i thought one could just download an app and flash the scooter by bluetooth?
Yes you can. This is for the people that get locked out of the scooter when doing the flashig wrong. :)
Actually asked that if that was possible in a FB group recently. I jailbraked my iphone once, and it bricked it. Dont want that to happen to my even more expencive scooter. Is it a high risk of bricking?
@@willynordboe5853 no but you have to dig deep into how its done and really understand what you doing. Some just flash just by looking in one video and often they flash a es o xiaomi program in the max. :)
@@WattsnabbAB Thanks! do you know of a video you can vouch for that does this correctly?
@@willynordboe5853 ruclips.net/video/PVky__tKlCw/видео.html
This doing it right and they provide firmware also.
That’s crazy
No soldiering opening nothing
Did mine from 25-31 with just the app to US version that’s it bro
What did you do
@@Badboy_billy yes you can change serial but that wont work on all g30 and if you want custom firmware then you need to st link it.
Amigo, me funcionó, lo que si el motor quedó con un sonido distinto, será dónde se sacó la silicona del controlador? Tengo un g30max lp
You maybe damaged mosfets when removed it. Have also done that :(
Hello I connect ESC to ST LINK but my computer say the device need more power? Must connect it to the akku?
Please help
Could you have solider it bad or connect it to 3v instead of 5v on st link?
hello friends in Indonesia there is a lot of scoter waste maybe because of regulations so it's not allowed on the highway I found a scoter in used goods of the MAX G30 type, can it be turned on after I charge it
66 hours of life but there is a code 32 key symbol, is the system program in the controller or can it be flashed or should I just change the controller, please guide, thank you
Hello I bought a second hand ninebot g30 max to be able to go to my heart appointments. When I tested the scooter it went up to 20 mph. The guy unbinded his account. I went home to charge it and when I went to drive the scooter it only went 13 mph. I noticed that the region was changed to DE and I'm trying to put it to region U.S. I Also noticed that the esc is 1.8.8. It's saying I have to downgrade to be able to switch region to U.S. can you please help me change it to REGION U.S.
Hi. Yes you can send in ypure controller and we can st link it. We charge 35us plus shipping to sweden. Maybe you have a repairshop that can help you in youre country.
@@WattsnabbAB do you have the esc version before the update of 1.8.8 version? If you have the zip file for the previous esc version. I could try to downgrade it and then I'll be able to switch the region back to U.S. please let me know if you can provide me the esc version before the 1.8.8 update. Thank you.
@@gerrellpadua8873 yes that what we sell.
www.wattsnabb.se/products/ninebot-g30-max-modellerna/reservdelar-till-ninebot-g30-max-modellerna/original-ninebot-g30-g30d-max-moderkort-kontrollkort
Hi, I have one ninebot max G30 and suddenly it stop charging when I connect it, how can I fix it?
I would forst try with diffrend charger( you have to connections in the bike). Then I would measure if the voltage reache the bms with a multimeter. Can be the charger inside that is broken.
Or just a cable lose.
hey, I have this same problem. charger is perfectly fine since it works with my other Ninebots, but my Max wont show percentage when charging
Are you able to perform a shunt mod on these boards?
Dont know what that is?
Hi there do you know if is possible to flash clones with Thai method?
Hi havent try that.
HELLO, I HAVE A PROBLEM. AFTER I APPLIED ALL THE STEPS FROM THE VIDEO, CHANGED THE SERIAL NUMBER AND CHECKED IF HE REALLY CHANGED IT. I TRIED IT AND SPINNED IT AT 30 KM / H. WHEN I CLOSED IT AGAIN AND TRIED TO STAND ON IT, IT SHOWS AN ERROR 10
Ok tjen you have done something wrong error 10 is wrong firmware on controller. Try to solider the controller and reflash it. Before fixing the serial and cfw try to see so it work.
Check also if you ble version is right.
@@WattsnabbAB reflash con st-link?
@@matmat3460 ??
Can i just use the app and download the firmware. And not do connections or Whatever you are calling it?
Yes but if youre scooter is locked you need to go this route.
@@WattsnabbAB wait, so if i wanna Flash the firmware i have to do this?
@@doug3826 yes but this video is for if you csnt flash it
Please help me I followed all the steps and it was successful but when accelerating it does not work it runs if I turn on the dash if it gives me a connection with the app but when pressing the accelerator it does not walk any idea help me please
Hi. Was that the problem before you did the steps? You can have damaged you mosfet or it can be somthing else wrong. Can even be somthing with the throttle. It's hard to say. What you can start to do I measure your mosfet to see that they are good. Then change the throttle. But can even be that some cables are not connected well. So try to check them to. Do you see you're battery on dashboard? Do somthing looks strange there?
I changed the region on my G30D and after this it stopped displaying battery percent while charging, it is charging but nothing is displayed and the lights are also not indicating that its charging.
If I set the region back to D this will fix the problem, does anyone know how to fix this?
You can use a costum firmware and don't turn off charging mode:)
Har samma problem som han hära snubben förstod inte riktigt vad är det jag behöver göra .tacksam
@@danihani2526 man behöver en speciell programvara man kan bygga den själv på scooterhacking
it will work for g30 max with the same serial number in the video and fake controller?
Dont think it will work on fake controller but unsure. Never tryied with them
@@WattsnabbAB okay thank u
Is there a USB 5V directly from the controller?
Yes on dashboard kable.
Why not solder from the top?
On g30d you have the st link pin under the board.
there are 3 dots where you can solder pins/leads as you wish, wouldn't that do the job? 5V dot must be available somewhere too.
@@diyroky under the middle Tower 3 dots, use this and the First 2 Pins 5v and GRND from Dashboard Connector.
Hey dude , do you sale Firmware speed for max g30 !?
Thanks
Yes if you want it install by me? Or look in the description
@@WattsnabbAB what do you mean ?
I wanna by a firmware is you sale them , so how can i contact you please?
Thanks
@@mhdryanslaha3909 please look in the description
is there a way to do it without soldering??
Yes if you have st link just press connectors against those pins
Vet du hur man gör på en e2s v2 Max longrange
Nej tyvärr
Hi do you accept if i send you my controller and ship it back to me?i will pay the work and the cost.i just need to unlock the speed for me to enjoy it going to work
Witch country are you from?
where to get that GEL to waterproof it back again ?
Search for 2 component silicon
Can you not just use the xiaoflasher app anyway and just change the region? (UK version)
Yes this is for those how got locked out using xiaoflasher :)
@@WattsnabbAB is everyone locked out when you flash and how do we know what controller we have ? mine just says g30 its a uk version doesnt say g30d
have you flashed yet
@@Midlothian-M1 yes I changed the region and worked just fine.
@@Midlothian-M1 if younhave regular g30 then the contacts are in the front. Search for ninebot g30 st link and you will find how tindo
Mine is stuck in an activation code and limited to 7MPH please help :/
How did it get there? Is it new? Where do you live?
@@AlexfreDholm i live in california and yes it is new i dont know what to do i tried contacting the company and they send me to leave a message on the phone then after i leave it with my information to contact me back they never do!
@@HossamElramy3 ok thats really strange. I guess you have tryed to activate it in the segway app?
I tried they ask for an activation code and the only option to do so if I have a Chinese phone number.
So strange!
@@HossamElramy3 to get a activation code send a email to this adress and give them youre serialnumber and ask them to help you.
service@ninebot.com
Please bro make how to flashing SNSC 2.3 ninebot max plus
Hi. If I hav there controller i can try but dont havet one.
first great video you can maybe make a video where you flash the dashboard from the g30d with the st link
That sounds like a great video!! Will do it when i get my g30. This was a costumer that got locked out of his g30d when he tried to flash it with Bluetooth.
Your a very clever man.
I need stock firmware for my new max g30 d2.. i flashed my new Scooter a few times and i get all sorts of wierd behaviour now, headlight always on and max speed 20kmh atm 🤣
It's better to use costum firmware the you set perimeters that you want
@@WattsnabbAB lyckades inte så bra med min förra custom firmware tyvärr.. fick den att frivarva 30 men den hade inget vrid och orkade knappa 20?vet inte riktigt vad jag gjorde för fel men misstänker att de blev nå vajsing med region eller nåt?`
har du möjligen en länk till en färdig fil?
@@TommieLjungberg ser o du gjort nått fel men här kommer en firmware. Giltig i 2 dagar.
linksharing.samsungcloud.com/jNuweMnxPj19
@@WattsnabbAB jag har flashat denna filen nu, bara kört på sport. gjorde 25kmh igen precis som jag ville, och känns betydligt starkare än orginal? kommer det påverka räckvidden nämnvärt? mvh Tommie
@@WattsnabbAB vafan nu tar den inte laddning ju :(
EDIT: verkar bara vara så att den inte längre visar att den laddar. för kan se att den ökar i ninebot appen. skulle va najs att få tillbaka det som den var :)
Hi where i can get that s t link
Have you try google ?
that such a friend, hey, my controller is different, it does not bring the points like the one you put, you can support me xfabor
Ya no existe el archivo 😢😮
Look in the titel :)
why you change the seril number
In a default after flashing and you can't ride without a valid one. That's why I get error in video.
@@WattsnabbAB i just bought mymaxmods 48v external kit, cant flash because my firmware is to new, dont have a windows laptop maybe you could sell me a pree flashed controller ??
@@sandmhoder yes sure. Have them here. You can send me firmware and ordet with costume firmware and I will send pree flasher controller with the firmware you want.
Chose: med costume firmware.
www.wattsnabb.se/products/ninebot-g30-max-modellerna/reservdelar-till-ninebot-g30-max-modellerna/original-ninebot-g30-g30d-max-moderkort-kontrollkort
@@WattsnabbAB i only speak english which ones for the external 48v battery
@@sandmhoder chose: med costum firmware
I have eror18
Hi that is hallsensor error that the motor is not connected or damaged. Try to connect the motor cables.
@@removecrypto3462 ok thanks
tjenaa grym video jag gjorde detta med st link men jag fick felkod 18 efteråt varför och hur åtgärdar jag detta tack
Error 18 är att du inte har motorhallsensor kabeln i. Så har inget med flashing att göra utan kontakten mellan motor och moderkort.
What does flash means?
when you hack youre scooter you are flashing it =)
Hello great video I help my allot can you make a video of how to flash the bms please I will help my allot
Sorry don't really see why flash bms,? You never need to touch it
Hi sir
And I’m not even binded owner
@@Badboy_billy when you Change serial you change owner. But if you want custom firmware then newer versions need to be st linked.
en polsk i norge? hehe
??
Sabato provo. Ho bloccato il mio g30max . Ho sbagliato firmware e si è bloccato con errore 10
Sorry only english o swedish
Where to find that usb with wires?
You can search on Google for st link v2