How to Easily Clean Diesel Particle Filter at Home using MOTIP DPF Cleaner | Ford Focus 1.6 TDCI

In this video I will show you how i cleaned the Diesel Particle Filter of my Ford Focus 1.6 TDCI 2007. You need 14mm wrench to open the temperature sensor which sits on top of the Diesel Particle Filter.
Spray the whole thing while moving the tip back and forth. Follow the instructions on the CAN and you are good to go.
Remember you need to use this when the Engine light has turned On and the car has lost the power. In other cases you can still use the DPF clean catalyst which you can add into the diesel tank and that will help with the regeneration
This method is when you want to give one last try before you actually remove the filter and clean it or replace it. I hope it helps you
Similar Product on Amazon USA
amzn.to/3uJDtzF
amzn.to/4a6jPxO
amzn.to/4182CQo
Diesel Particle Filter
Diesel Particle Filter clean
Diesel Particle Filter regeneration

[@stevehufngel7221]

what a groupride!

[@mrpozitiv4ik74]

Danke dir 🎉

[@newcastleboilermaintenance4956]

Thank you

[@nicemihcos]

Hello, does it still holds on ?
How are the pressures, 2.46 psi = 16~ kpa and on forums I saw that already over 10kpa (max) the filter means its blocked.

[@adnansgarage]

Yes it is blocked pretty much. I did all these as a temporary solution but had to change dpf filter in the end

[@adamphoenix8741]

Hi could you help me out and see if you can find the bank1 sensor 1 sensor I have the light and fault code for the lambda and can’t find it same engine

[@adnansgarage]

you mean you cant find the location of the lambda sensor?

[@muhammadaamirhussain6951]

AoA
I also have Ford focus mk2 1.6 diesel in Sweden with the same DPF issue. I did regeneration a year ago and it worked fine. Now the car is showing agin the code. Are you satisfied with the results of this direct fluid insertion?

[@adnansgarage]

wsalam, how did you regenerate last year?
no i am not satisfied with the results because i think in my case my cars dpf was clogged uptil the point where only replacement was the solution. the code came back after a month. But it could work for some time in your case. it is quite cheap so worth a try. Usually Ford dpf are recommended to be changed after 120k kms

[@muhammadaamirhussain6951]

I went to a mechanic last year and he did the re generation as you have shown in the previous video. I think it’s clogged now and needs replacement. I am thinking to buy an OBD reader to regenerate my self. Do you recommend any OBD reader for DPF regeneration?
I bought from Jula but it didn’t worked.

[@MrMaster2262]

@muhammadaamirhussain6951
The OBD2 reader will only tell you the
fault codes... plenty on market are cheap and
will do the same job. (foxwell) OBD2 is
a good one to use roughly £20-£30. i would
try using two things for DPF clean... buy
Mannol DPF foam cleaner. the foam is
better than the liquid version. also use a
diesel additive in the fuel tank that supports
DPF regeneration. simply put the can in
the fuel tank before filling up with fuel. the
additive will burn the soot inside the DPF
at a much lower temperature and the foam
cleaner will loosen the soot. the two DPF
cleaning solutions will work better together.
Go for a nice long drive getting the revs up
& the DPF will be as good as new. 😉👍

[@Djreucroft]

Your ment to clear all. Faults first and once added the product , use a laptop or scannner to force a regen …..

[@adnansgarage]

If you clear all the fault and then force regeneration, you end up damaging many things under the hood and that happened to me so if the car doesnt allow forced regen with error codes then dont do it
If th efilter is blocked and you clear the codes, try to force regen on blocked filter, engine will rev up and the exhaust has to come out from somewhere. In my case one plastic pipe blew up and two injector seals blew after i cleared codes and forced regen