Thanks that help alot today ! Sunday today and I still have all my work uniforms to wash and my machine play funny today 😄 not good😅 I glad people do this videos to help us 👍
My Lindo 300 drum smells horrid. I am wondering if it is draining properly. The drain hose currently extends up above the height of the machine before dropping down into the standpipe. Is pumping above the height of the machine likely to cause drainage problems?
According to another RUclips video, to unblock the drain pump, you have to turn the machine on its side, then unscrew the pump from UNDER the machine, clean it and replace it. That's assuming your machine isn't draining.
Hi There Thank you for your replay .... However the Zanussi lindo 300 we have is a 9Kg a Intermittent spin some times not all times so Please any where can you please send me link where i can buy the parts required saying that i have a spare mother board.... please let me know as really is obsessing this problem . Kindle thanks. Joe
Hi. My lindo 300 10kg model is not rinsing properly at all on any cycle. I use one ariel pod even when the washer is full. I never use two. It's usually on a towel wash or bedding wash ( 60c ). I have extra rinse option on and still there are loads of sud residue left during the final spin. I run a hot 90 degree cycle with nothing in it once per month and use Dr beckman cleaner every 90 days. Still no joy? Any ideas please? I love this machine and it's only three years old. Thanks :)
Is it draining fast enough? If its connected to sink spigot these can create drainage problems. So check that the end of the hose and spigot is clear of gunk. There is also a inaccessible filter to the general public attached to underside of the wash tub. Which can be removed cleared and re-attached by a competent person.
@@whichwasher2007 hey now that you mention it sometimes it sounds like there is a drainage lag and when spinning you can hear the laundry sloshing in the water for a bit. Drain pipe is in a regular stand pipe.
Er..cry. because there is no way to drain the water from the tub. The only slim chance you may have is between 2 or mabey 3 people. Pull the machine out. Put the drain hose into a bucket and 2 of you carefully tilt the washer backwards. I think there is emergency door release but I need to investigate further myself.
Hi there. Thanks for the video. I've been getting an E10 error - which is a problem with water coming in. Regular cycles give this error but it fills fine when I put the machine on rinse only cycle. I put it in diagnostic mode like in your video but the first test (pressure switch?) when it's on 30@30 light does nothing but then when I carried on to the next test (direct fill/led at Cottons) water came in fine. The rest of the tests seemed to work fine. Any ideas please?
Faulty fill valve. It has 2 of them. 1 for direct fill. 1 for main wash dispenser fill. Both combined for fabric softener. Main wash 1 is stuck closed.
Apart from the difficulty of understanding the accent and speed of each step, why oh why must we have that bloody awful music in the background. If I want to listen to music I'll go somewhere else.
No. But it's much simpler on yours. Push and hold program and temperature buttons together while pushing the power button. And hold untill the leds start cycling through. Then use the program button to select functions.
whichwasher2007 When I do as you say it just comes up as error and turns off, are you sure these are the right two buttons to hold down, thank you in advance
I started doing this and before it started I got E11 error so I moved it check the pipes at the back nothing and then a did this again, I got right the way to the ELE test and it didn’t feel warm when I touched it the the error E11 again .... help! (It’s only 5 months old)
Hi there, just looking for a hudge help i have both a zanussi lindo300 at 4 years a go since then the machine is working good for the last 5 months is showing a e05 meaning iss a erro 5 we done all posible . now te machine is not spining at 1400 or 1200 even 800 i even both a mother board with the cost off 180£ and still the same. Now when i reset fowling your video wee can clear the erro andd ssshow no erro probleme is not spining at any speed. I have contacted zanusssi anddd i cant get any where, so the help line is crab, do you can you help with this issue?
Thanks that help alot today ! Sunday today and I still have all my work uniforms to wash and my machine play funny today 😄 not good😅 I glad people do this videos to help us 👍
Good, you're testing!
Thankyou mine was stuck in pause mode now working fine
How to you change the paddles on this thing i cant find anything.
Hi, thanks for your video. My machine has an error light just to the left of the 30, any ideas as the machine does nothing now!
Many thanks in advance
My Lindo 300 drum smells horrid. I am wondering if it is draining properly. The drain hose currently extends up above the height of the machine before dropping down into the standpipe. Is pumping above the height of the machine likely to cause drainage problems?
Same problem here. How did you get rid of the smell?
Do these machines have an accessible lint filter, I don't see one on the front?
No they dont, they dont have a filter at all.
@@whichwasher2007 inside the machine under the drum ,On the backside
According to another RUclips video, to unblock the drain pump, you have to turn the machine on its side, then unscrew the pump from UNDER the machine, clean it and replace it. That's assuming your machine isn't draining.
Service mode on your washing machine is good
Is there a way to just do a spin on this machine as I can’t find one? TIA
0:03 start
Will doing this get rid of the smell or can someone recommend something else?
Thanks
I am not sure what Wool/Handwash does in service mode
Hi There Thank you for your replay .... However the Zanussi lindo 300 we have is a 9Kg
a Intermittent spin some times not all times so Please any where can you please send me link where i can buy the parts required saying that i have a spare mother board.... please let me know as really is obsessing this problem . Kindle thanks. Joe
Hi. My lindo 300 10kg model is not rinsing properly at all on any cycle. I use one ariel pod even when the washer is full. I never use two. It's usually on a towel wash or bedding wash ( 60c ). I have extra rinse option on and still there are loads of sud residue left during the final spin. I run a hot 90 degree cycle with nothing in it once per month and use Dr beckman cleaner every 90 days. Still no joy? Any ideas please? I love this machine and it's only three years old. Thanks :)
Is it draining fast enough? If its connected to sink spigot these can create drainage problems. So check that the end of the hose and spigot is clear of gunk. There is also a inaccessible filter to the general public attached to underside of the wash tub. Which can be removed cleared and re-attached by a competent person.
@@whichwasher2007 hey now that you mention it sometimes it sounds like there is a drainage lag and when spinning you can hear the laundry sloshing in the water for a bit. Drain pipe is in a regular stand pipe.
Brilliant very clear thanks. Loved hearing the little one, made me laugh
What even does the tab thing even do on a washer since they all pretty much have them
E21, water won’t drain. I’ve reset it to E00. The water level is high so that the door can’t be opened. What to do next? Please help. Thank you
Er..cry. because there is no way to drain the water from the tub. The only slim chance you may have is between 2 or mabey 3 people. Pull the machine out. Put the drain hose into a bucket and 2 of you carefully tilt the washer backwards. I think there is emergency door release but I need to investigate further myself.
dont you just run it on the cotton program at 60 degrees using a washing machine cleaner product ?
Thank youb foir whty extra cool tuturiul i was have problem withh thiees modeeeeel sepicifacyl ty
When I go to Jacqui’s house I will go straight to the ELE mode and the water should warm up once in the machine
very good
Hi there. Thanks for the video. I've been getting an E10 error - which is a problem with water coming in. Regular cycles give this error but it fills fine when I put the machine on rinse only cycle.
I put it in diagnostic mode like in your video but the first test (pressure switch?) when it's on 30@30 light does nothing but then when I carried on to the next test (direct fill/led at Cottons) water came in fine. The rest of the tests seemed to work fine.
Any ideas please?
Faulty fill valve. It has 2 of them. 1 for direct fill. 1 for main wash dispenser fill. Both combined for fabric softener. Main wash 1 is stuck closed.
The ELE test will only go on for a bit but the start light won’t go off until you turn the washer off
Thanks
My machine is leaking underneath, how can I diagnose where it’s coming from please?
Nice video Thank you!
Apart from the difficulty of understanding the accent and speed of each step, why oh why must we have that bloody awful music in the background. If I want to listen to music I'll go somewhere else.
How do I put the Zanussi TCE7124W in test mode?
Hold start and buzzer, power on, then turn dial one notch to A.
Would this test work on A Zanussi WJD1457W, I think my pressure switch is gone or the tubing damaged
No. But it's much simpler on yours. Push and hold program and temperature buttons together while pushing the power button. And hold untill the leds start cycling through. Then use the program button to select functions.
whichwasher2007 When I do as you say it just comes up as error and turns off, are you sure these are the right two buttons to hold down, thank you in advance
I managed to get into maintenance mode once but now I can't get back into it
Got back into maintenance mode getting E69 code is that faulty heating element?
Its heater related. Is it starting a cycle then immediately going to 1 minute and always draining?
@@whichwasher2007 Strangely no it completes any cycle. It's only when in maintenance mode that it does not and only shows code in maintenance mode 🤔
I started doing this and before it started I got E11 error so I moved it check the pipes at the back nothing and then a did this again, I got right the way to the ELE test and it didn’t feel warm when I touched it the the error E11 again .... help! (It’s only 5 months old)
Hi there, just looking for a hudge help i have both a zanussi lindo300 at 4 years a go since then the machine is working good for the last 5 months is showing a e05 meaning iss a erro 5 we done all posible .
now te machine is not spining at 1400 or 1200 even 800 i even both a mother board with the cost off 180£ and still the same. Now when i reset fowling your video wee can clear the erro andd ssshow no erro probleme is not spining at any speed. I have contacted zanusssi anddd i cant get any where, so the help line is crab, do you can you help with this issue?
If its a 8kg model it will likely be the brushes. If its 9kg or 10kg it will likely be a bad connector to the motor, motor board or motor itself.
Had to quit midway due to the child shouting in the background! 😂
Service wash with clothes
Not in this.
Why not wash race : Zanussi Essential vs John Lewis ( Old ) tub and cleaning on the cottons 60 or cottons 95 and max spin!!!
Po
Does not work. Makes zero sense what you said
because his is 9kg so...
He is not good at explaining I guess