How to Replace Front Lower Control Arms 2011-2020 Toyota Sienna
HTML-код
- Опубликовано: 18 окт 2024
- Buy Now!
New Control Arm from 1AAuto.com trq.video/ib-1...
This video shows you how to install new control arms in your 2011-2020 Toyota Sienna. Control arms are a crucial part of the suspension system of your vehicle. They not only carry the load of the vehicle to the wheel, but they typically also maintain its alignment. Control arms are typically large and strong, so you may be surprised it needs replacing. They contain rubber bushings for smoother rides at the cost of eventual wear. When those bushings run out, that can have a negative impact on the ride and safety of your vehicle.
This repair was done on a 2011 Toyota Sienna Limited 3.5L Mini Passenger Van 4-Door AWD Automatic and the process should be similar on the following vehicles:
2011 Toyota Sienna
2012 Toyota Sienna
2013 Toyota Sienna
2014 Toyota Sienna
2015 Toyota Sienna
2016 Toyota Sienna
2017 Toyota Sienna
2018 Toyota Sienna
2019 Toyota Sienna
2020 Toyota Sienna
Tools you will need:
• Pry Bar trq.video/oadT...
• 19mm Wrench trq.video/oaj5...
• 10mm Socket trq.video/obTP...
• 12mm Socket trq.video/ocnn...
• 14mm Socket trq.video/ocnn...
• 17mm Socket trq.video/ocnn...
• 19mm Socket
• 21mm Socket
• 22mm Socket trq.video/ovn-...
• 30mm 12-Point Socket trq.video/oaC-...
• Trim Tool Set trq.video/oaFe...
• Locking Pliers trq.video/op2-...
• Ratchet trq.video/ocmY...
• Socket Extensions trq.video/ocnn...
• Torque Wrench trq.video/obo6...
• Block of Wood
• Gloves trq.video/obuo...
• Liquid Thread Locker
• Safety Glasses
• Floor Jack trq.video/oaHI...
• Hammer
• Jack Stands trq.video/oatX...
• Pole Jack
• Punch
• Wheel Chocks
• Wire Brush trq.video/oAc-...
Subscribe: / @trq
Check out our playlist:
Toyota Sienna 2011-2020 3rd Generation: • Toyota Sienna 2011-202...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money
Just wanted to say thanks for this video, it literally saved my family almost $3000. I looked up the reason why it was so expensive and it said that Toyota has this as a 10 hour job. Not sure why something that has to be changed between 70-150k miles was not designed to be done so more easily.
What a nice, slow and accurate video. Thank you
+@BindasBadshah Thanks for watching. Buy the part in this video on 1AAuto.com: 1aau.to/m/Shop-TRQ
Aren’t you supposed to load the control arm before tightening all the bolts so you do not stress the bushing?
Thank you for the instructional video. I noticed removal and installation of ball joint is missing
Thank-you
How can you tell if the control arm needs to be replaced? What are the signs?
Bro only showed how to do the left side
P3rfrct timing my control arms just came in