Most Excellent Video. I had no clue how to add a load resistor. Now I know. Your anecdotes and explanations were on the mark. Not too long, not too short. Thank you very much.👍
Hi, great video, I'm a newbie and now I can better understand the resistors in the power supply, thanks, at 22:43 maybe you mean "Watts" instead of "Ohm"
Extremely informative video! So many content producers don’t go through the hows and whys of the subject. As far as repeating yourself, you shouldn’t worry about it. Think about it as reiterating or highlighting the more important points. I do have a question that may be related to this subject. I see on some Volt/Amp (panel) meters they have a “Shunt resistor” included, others don’t have them. Is that basically another term for a load resistor? Is a shunt only required when is it higher amperage? The panel meters that don’t come with a shunt included do they still need a shunt to work properly? Thank you in advance.
I am building a power supply, but not with a ATX PS. I bought 24V 6A power supply, and a step down converter 150W and 12A, so it can handle 6,25 A. I have to use a load resistor too? I want to use that supply for a soldering iron station, so i dont know the exact power i will need and how much current i want
My power supply won't start up (I did a jumper from green to black (ground)). No fan, nothing. I accidentally bought a 50W 20ohm resistor, knowing nothing about them. My power supply is rated for 305 watts maximum. The bundle of wires rated for the highest amps is the 5v (22 amps), so that's the one I connected the resistor to (one side red, the other black). When I power it up, nothing happens. So I tried jumping the green to the second bundle of black wires (ground). I also jumped the brown wire (which is 3vSense) and jumped it to the 3.3 v bundle of wires (orange). None of these things worked, and I get no fan, and when I take the meter to the various lines, it just reads zero. It seems dead. Can anyone offer guidance? Did I kill it with the 50W 20ohm resistor? It came out of my computer that worked up until the day I took it out for this project. Thank you.
If PSU does not start at all when you do a jumper wire from green to black without load resistor, it might mean PSU itself is not working. It would be good to test it in actual computer configuration No you did not kill your PSU with a load resistor, as 20 ohms on 5v power line would draw 0.25A and generate 1.25w of power. PSU was probably dead already before you connected the load resistor. Still to be sure, connect it to some configuration(motherboard+gpu+hdd at very least although I would add a DVD drive) and see if it turns on, if it does that means you need more load, like 5 ohms resistor on 5v line or 2.5 ohms. And maybe you need more load on other voltage lines, like I said in the video, some PSUs need loads on multiple voltage lines.
I'm building a bench PSU, the 5v is stable with no resistor but the 12v and 3.3v are not, do I still need to put a load on both of those rails or with the 5v being stable is enough? The 5v rail is the highest amperage with 30A
God bless you for saying exactly what I was thinking, his analogy is good but the useless unrelated explanation could have the opposite effect and can confuse people, but in all honesty I still appreciate the the time this man spent to make the video and make us understand the concept .
So, for you experts, maybe it was too much. But for us Noobs, I am very grateful for the explanations and anecdotes. We all are at different levels, and we all step off from where we are.
Most Excellent Video.
I had no clue how to add a load resistor.
Now I know.
Your anecdotes and explanations were on the mark. Not too long, not too short.
Thank you very much.👍
Hi, great video, I'm a newbie and now I can better understand the resistors in the power supply, thanks, at 22:43 maybe you mean "Watts" instead of "Ohm"
Very good, Thank You.
Great, great and very great ! ! !
😁
Extremely informative video! So many content producers don’t go through the hows and whys of the subject. As far as repeating yourself, you shouldn’t worry about it. Think about it as reiterating or highlighting the more important points.
I do have a question that may be related to this subject. I see on some Volt/Amp (panel) meters they have a “Shunt resistor” included, others don’t have them. Is that basically another term for a load resistor? Is a shunt only required when is it higher amperage? The panel meters that don’t come with a shunt included do they still need a shunt to work properly?
Thank you in advance.
Thank you so much for this informative video.
4:00 Not only DC needs to be as "stable" as possible....Same goes for AC. Preferably AS STABLE AS POSSIBLE.
I am building a power supply, but not with a ATX PS. I bought 24V 6A power supply, and a step down converter 150W and 12A, so it can handle 6,25 A. I have to use a load resistor too? I want to use that supply for a soldering iron station, so i dont know the exact power i will need and how much current i want
My power supply won't start up (I did a jumper from green to black (ground)). No fan, nothing. I accidentally bought a 50W 20ohm resistor, knowing nothing about them. My power supply is rated for 305 watts maximum. The bundle of wires rated for the highest amps is the 5v (22 amps), so that's the one I connected the resistor to (one side red, the other black).
When I power it up, nothing happens. So I tried jumping the green to the second bundle of black wires (ground). I also jumped the brown wire (which is 3vSense) and jumped it to the 3.3 v bundle of wires (orange). None of these things worked, and I get no fan, and when I take the meter to the various lines, it just reads zero. It seems dead.
Can anyone offer guidance? Did I kill it with the 50W 20ohm resistor? It came out of my computer that worked up until the day I took it out for this project. Thank you.
If PSU does not start at all when you do a jumper wire from green to black without load resistor, it might mean PSU itself is not working.
It would be good to test it in actual computer configuration
No you did not kill your PSU with a load resistor, as 20 ohms on 5v power line would draw 0.25A and generate 1.25w of power.
PSU was probably dead already before you connected the load resistor.
Still to be sure, connect it to some configuration(motherboard+gpu+hdd at very least although I would add a DVD drive) and see if it turns on, if it does that means you need more load, like 5 ohms resistor on 5v line or 2.5 ohms.
And maybe you need more load on other voltage lines, like I said in the video, some PSUs need loads on multiple voltage lines.
I'm building a bench PSU, the 5v is stable with no resistor but the 12v and 3.3v are not, do I still need to put a load on both of those rails or with the 5v being stable is enough? The 5v rail is the highest amperage with 30A
Nice sir....
Tq very much
23:00 EVERY(!!!) resistor has to handle "a certain" amount of power....
Very interesting, but you lost me among the many words for nothing
Nice Win XP in 2023 🤣😂
although your presentation is good, you unfortunately drown your listener into a sea of useless details.
God bless you for saying exactly what I was thinking, his analogy is good but the useless unrelated explanation could have the opposite effect and can confuse people, but in all honesty I still appreciate the the time this man spent to make the video and make us understand the concept .
So, for you experts, maybe it was too much.
But for us Noobs, I am very grateful for the explanations and anecdotes.
We all are at different levels, and we all step off from where we are.