Trial and error, I like your style. I just built a bear Creek arsenal 7.62x39 upper on a Anderson lower have not had a chance to test it yet because where I live “city”. I will test eventually and will let you know.
It's always good to see some informative content on yoofloob . You pretty much have to wade through a bunch of manure to find any diamonds. I know a little bit of this and that and can usually spot a bs'er. I worry more about the beginners that can't distinguish bad advice from dangerous ba Thanks again
I got a mutant x39 on aero precision lower upper. Aero precision upper FDE Aim surplus BCG, Geissele 2 stage trigger. Duramag by c products. Never had failure to ignite issues with the geissele trigger. Did put a BRC extended firing pin in it. Things a sun moa rifle. I love it. All FDE too
Replace the firing pin with sn enhanced and try the 2 stage Larue tactical MBT trigger. 100 bucks in upgrades and your light primer strikes are solved.
Got my BCA 7.62x39 for $399 a few months back. Did a ton of work to it and it's my go to hunting rifle sub moa 100yds benchrest. Green Mountain 16" barrel Guntec Keymod FF rail w/adjustable gas block A2 flash hider (works amazing compared to my yhm phantom on my WASR so why change it) Failzero BCG & CH Black rifle arms Extended firing pin and xp hammer spring Failzero Buffer tube and FCG Trs-25 with vortex magnifier. I had no issues with light primer strikes until i swapped the trigger out then the firing pin and spring swap helped immensely now the hammer drops like an ak and the firing pin sticks out like my SKS. Black rifle arms is one of the very few manufacturers that actually extend the pin unlike most that radius a 5.56 one. 1500rds in about 300 after upgrade no issues since.
@@tristarcustoms77 just bagged an 8 point buck at 200yds! Got a chance to push my rifle out to 300yds getting 3in groups outshooting my friend's ruger ar in 5.56.
Best video ever thank you for sharing I did the removal on the striker like you did with a drill and man my AR-47 shoots like a champ, a great video still using mil-spec trigger but I don't mind. It works and that's what matters thank you again
Your Lower is it polymer... I made one with polymer and I installed the wolf hammer springs. I used the ASC 20rd mag. I believe that the name of the mag brand. But I have no issues with any type of steel casing. The buffer I used is a H2 but I forgotten where I got my bcg. I think dpms is what I want to say. Anyhow so far so good with yours and mine
May I suggest that you look at the Hipertouch triggers (24 series) that offers a $6.00 7.62x39 spring kit upgrade that ensures no light strikes and maintains a 3.5 lb trigger pull ? Just a thought, but looks like what I'll use on my upcoming build. :) As to primer seating depth, that's not the difference causing the light strikes. The steel cased ammo with their mil spec primer has a greater distance between the anvil and striker within the primer cup. If you reload, it's always safer to have the outer surface of the rimer slightly below the level of the rear of the case. :)
Nice build. Just finished mine. Enhanced firing pin is highly recommended. Extra power spring will help but not always needed. I got them for the extra insurance. Also, you can run the nickel boron carrier and swap the bolts if you wanted too. Looking forward to more updates. Nice build. 👍🏾👍🏾👍🏾
Abraham Lopez I probably didn’t make it real clear in the video but should have, that I ended up using a regular mil-spec spring instead of an extra power spring. The mod I was doing to my firing pin is the same as an enhanced firing pin to the best of my knowledge. And I definitely considered running that nickel boron carrier with my bolt. I’m going to run the carrier I have for a while and check it for unusual wear. I want to sell the nickel boron one and if I can get more for than what my current BCG cost I’ll be able to reduce my overall build price, which is always one of my goals 👍🏻Hopefully I’ll be able to post an update video soon with hunting footage within the next month🤞🏼
Cumberland Gap Tactical awesome. I love doing budget builds. I just finished my x39. I went with a sidecharge so it up there compared to my other budget build but I have been wanting one so I figured I would go for it. Looks like you got a good setup. Can’t wait to see more updates
Yea Jordan would like to see the hunting video. You make a lot of sense talking about selling the one bolt to bring price down. I have to start thinking that way. One of my biggest problems is when I buy parts for my guns,I always say I will sell old. But I can never let anything go. I'm a hoarder when it comes to gun parts and it's not like I have money to spare. I have to get over this bad habit.
I totally understand brother. And even being in the firearms business it sounds logical to keep “extra parts” but if those parts are worth money you need to move them to keep cash flow coming. The same idea is true for the average gun guy. If you ain’t using that junk get rid of it to buy things that you’ll get more use/enjoyment out of. It takes time to get into that mindset. BTW I wish I had better footage of the deer I killed with my 7.62 AR but it really wasn’t worth watching lol. And I currently traded that gun for a brand new set of 35’s for my truck 😂
What Ive found with building ARs in x39, the Rock River Arms National Match 3.5lb 2 stage trigger feels great and has given me great results with primer strikes. They do sell a red, heavy hammer spring, for 2 bucks that will ignite the hardest of mil-surp primers.
@@tristarcustoms77 the trigger can be found for $80. Its regularly on sale from places like Right to Bear or Primary Arms. Any more, that trigger, TC bcg, and CPD mags are a staple for x39 builds. Here in Texas I go hog hunting often. Its a great setup for that. We have a Helicopter hunt on 3/21 with everyone using ARs in x39.
Your Lower is it polymer, Not had good luck with them. Broken two at buffer tube separation. so change back to standard. Maybe just bad quality forgot where I got them from. But works great now with a new billet lower. with the enhanced firing pin and one pin I milled both work great.
Great video. If you had to do it again would you build another one? I am looking to build 1 in the next few weeks and would like to know if it is a keeper.
I checked it out, you are gonna find the right trigger. I can honestly say you never give up. Does it run fine with a mil-spec trigger and enhanced firing pin?
The Enhanced Firing Pin is a Must Have for 7.62x39 ARs if you will be shooting Steel Cased (Hard Military Primer) ammo. Try a Red-X Enhanced Firing Pin for only $10 to your door.
I used a complete psa lower with a bear creek upper on mine with AR Stoner magazines (specific to caliber). Was having a failure to fire about 1 in every 10 (shooting Tula, Wolf seemed to be a little better). Changed to enhanced titanium firing pin and it runs perfect now.
Alright, alright, alright...(sniff...)😂🤣😂 Good video, just bought the BCA 7.62×39 and am already looking for an enhanced firing pin and heavy trigger spring! Thanks for the info!
@@HardHeadMilitary its difficult to get any less expensive than the BCA upper. Primary Arms has some good sales on Radical 7.62 uppers too. Ive built several. Some have a BCA x39 barrel. At the holiday sales the barrels are $50.I also have built them with Faxon and Diamond back barrels. Faxons are the best, but are they worth 3x the cost of a BCA barrel? Maybe. Tool Craft makes a great BCG in x39 that comes with an enhanched firing pin. They run about $80. If you are really scrimping, Unbranded AR sells just the x39 bolt with enhanced pin for $40. You can drop that into any of your 556 carriers. CPD mags are the only 28 or 30 round mags that Ive found work 100%. ASC or any other 10 rounders work fine too, but not the 30 rounders. One thing people make a big mistake on, it is not cheaper to shoot 7.62 x 39. If anything, it is more expensive. Mags cost more, steel cased ammo prices are the same, brass is more expensive for x39 (significantly), and hunting ammo is more expensive for x39.
I think I'm gonna build one of them for hunting on the cheap. Can be one that I can beat ,take out in the weather etc. But after listening him sniff,which my wife tells me to blow my nose all the time. But now I know what it looks and sounds like on the other end. Blow your nose. I will from now on. I'm just a bit picky I guess but must be others out there too. Good video though. Gun looks fine to me
You still got the bolt carrier up for grabs? Btw, you can pick up a 6.5 grendel barrel for like $80 + it'll run the 7.62 magazine & should run the same bolt as well (6.5g uses 7.62x39 parent case) but u can upgrade to the type2 6.5 bolt if u wish.
TNT Tactical I kno bear creek got in some trouble with ICE, but I bought a 24" stainless fluted BCA barrel in 6.5g for under $90 & use my 30rd 7.62x39 ar mag. Steel case stuff is $5/box and the hornaday black is about $1/rd but u can get 1K yd range if ur barrel is decent!
Ok question I have a ks-47 PSA Hybrid upper and I got a ar 15 plumcrazyarms multi cal lower receiver laying around I put it together and I'm tryna ask is it compatible
Nice video I'm doing a 7.62 build also just waiting on a few more items . I was wondering did you try the enhanced firing pin I've heard its needed sometimes to fire cheap steel case ammo aka TULA looking forward to more updates
Benjamin Ledbetter if I’m not mistaken the “enhanced firing pin” is basically the same thing as the firing pin mod that I showed in the video. So that’s why I haven’t tried it but if you try it let me know what you think about it.
The enhanced pin isn't necessary for steel case hard primer stuff, just need to get the jp enhanced hammer spring, you can even use the reduced power trigger spring but need the hammer spring. $13 spring kits
Try bobbing the hammer. If you take the tail off of it you reduce the weight of the hammer itself and the lighter spring can get it moving faster. Also don’t dry fire the rifle with the upper off of it you’ll destroy your lower dude.
I like the way you think! I’ll definitely give that a shot when I get some time. And I try not to make it a habit of dry firing it like that but just did it for video purposes.
zack mcclain merry Christmas! If you took the time to watch my video and make a sensible comment I’ll take the time to write you back is the way I look at.
Rex Martinez in my area you can find complete 7.62 uppers for really cheap at gun shows. That includes everything you need besides magazines. But if you just want to try to keep your hand guard that you currently have you need to buy: a barrel, gas system (most 7.62 barrels have a larger profile than a 556 setup), muzzle device, bolt carrier group (or just the bolt if you can find one). I think that’s it
Wow that was painful,,I know that you were just checking to see if the dam thing would fire,if you are going to use it for deer hunting shouldn't you be using the ammunition that you would be hunting with? That Tula ammo is crap ! Man I made a mistake one time and got ripped off and bought 100 rounds of that Tula crap for my rifle same AR platform filled up a 30 rounder got to #10 and tossed the rest of that shit in the bushes,, out of 10 rounds 6 of them fired, basically every other round went bang,, pulled out some wolf ammo and got to 15 ,and only loaded 15 and kept them but not for my AR ,I got some fiochi (spelling?) Brass case and just felt better about it and some other brass rounds and haven't been able to make my 7.63x39 AR upper misfire again,, on my 3rd case of 1000 pretty good,, I was hoping your range day was going to be a good day then I heard the worst word on the planet..TULA !!! I know this dude that uses Tula in his carry sidearm!! If he was a family man or had more sense I would tell his ass about that bad decision, but maybe he won't shot himself one day,lol
Never had a single issue with Tula in any of my firearms. My x39 AR loves it. Wolf is made different cartridge works with Tula being the most common for their 7.62 x 39 ammo. Tula make the 8m3 "effect" bullet. It is a very good performing bullet.
Ar stoner Magazines are the best ones you can get even tho some of the reviews are shitty but ive had two 30 rounders for about 7 months an (Knock on wood) havent had a issue yet. Little tip with the mags spray some gun lube under the Sitting plate in the Magazine so the spring an plate slide easier because when i first got mine they were stiff.
8:05 Where's the kaboom? There was supposed to be an Earth-Shattering Kaboom!
Good video. Enjoyed watching the trial and error and solution to get it running. I bought a BCA upper in 7.62x39 and will try it out this weekend👍
Trial and error, I like your style. I just built a bear Creek arsenal 7.62x39 upper on a Anderson lower have not had a chance to test it yet because where I live “city”. I will test eventually and will let you know.
How did it go?
You’re smart bro. I dig you skills and knowledge
Thanks for showing what DIDN'T work as well as what does. That's as
important to me to know. Most people would have edited all that out.
Thanks man! I always try to show the failures too because I almost always learn more from those. I appreciate the comment
It's always good to see some informative content on yoofloob .
You pretty much have to wade through a bunch of manure to
find any diamonds. I know a little
bit of this and that and can usually
spot a bs'er. I worry more about the
beginners that can't distinguish bad
advice from dangerous ba
Thanks again
You have no idea how helpful this video was for me! Thank you so much for such a great video!!!
Glad to help man!!
I got a mutant x39 on aero precision lower upper.
Aero precision upper FDE
Aim surplus BCG,
Geissele 2 stage trigger.
Duramag by c products.
Never had failure to ignite issues with the geissele trigger. Did put a BRC extended firing pin in it. Things a sun moa rifle. I love it. All FDE too
Replace the firing pin with sn enhanced and try the 2 stage Larue tactical MBT trigger. 100 bucks in upgrades and your light primer strikes are solved.
Got my BCA 7.62x39 for $399 a few months back. Did a ton of work to it and it's my go to hunting rifle sub moa 100yds benchrest.
Green Mountain 16" barrel
Guntec Keymod FF rail w/adjustable gas block
A2 flash hider (works amazing compared to my yhm phantom on my WASR so why change it)
Failzero BCG & CH
Black rifle arms Extended firing pin and xp hammer spring
Failzero Buffer tube and FCG
Trs-25 with vortex magnifier.
I had no issues with light primer strikes until i swapped the trigger out then the firing pin and spring swap helped immensely now the hammer drops like an ak and the firing pin sticks out like my SKS. Black rifle arms is one of the very few manufacturers that actually extend the pin unlike most that radius a 5.56 one. 1500rds in about 300 after upgrade no issues since.
Sounds like you’ve built an awesome rifle man! Thanks for all the info I appreciate it!
@@tristarcustoms77 just bagged an 8 point buck at 200yds! Got a chance to push my rifle out to 300yds getting 3in groups outshooting my friend's ruger ar in 5.56.
The hammer spring is not needed. Just the enhanced firing pin. Not longer, but shoulder cut differently so it protrudes a bit more.
If you buy (and I highly recommend them) a Tool Craft BCG for 7 62 x39, they come with an enhanched pin.
Best video ever thank you for sharing I did the removal on the striker like you did with a drill and man my AR-47 shoots like a champ, a great video still using mil-spec trigger but I don't mind. It works and that's what matters thank you again
That’s great to hear. I’m glad it helped you out
Get a fail zero bolt with the enhanced firing pin. I was having similar problems as you, the higher end bolt made the difference!
Your Lower is it polymer... I made one with polymer and I installed the wolf hammer springs. I used the ASC 20rd mag. I believe that the name of the mag brand. But I have no issues with any type of steel casing. The buffer I used is a H2 but I forgotten where I got my bcg. I think dpms is what I want to say. Anyhow so far so good with yours and mine
thanks for this was wondering if my FMK lower could handle the 7.62x39 and you have some great troubleshooting too. good job mate
You can use the JP enterprises light trigger spring and still run the enhanced hammer spring for hard primer steel case, I believe kit is under $15.
May I suggest that you look at the Hipertouch triggers (24 series) that offers a $6.00 7.62x39 spring kit upgrade that ensures no light strikes and maintains a 3.5 lb trigger pull ? Just a thought, but looks like what I'll use on my upcoming build. :) As to primer seating depth, that's not the difference causing the light strikes. The steel cased ammo with their mil spec primer has a greater distance between the anvil and striker within the primer cup. If you reload, it's always safer to have the outer surface of the rimer slightly below the level of the rear of the case. :)
MarineBoar thanks for the input! I appreciate your knowledge and willingness to share. I’ll definitely look into that spring kit.
Nice build. Just finished mine. Enhanced firing pin is highly recommended. Extra power spring will help but not always needed. I got them for the extra insurance. Also, you can run the nickel boron carrier and swap the bolts if you wanted too. Looking forward to more updates. Nice build. 👍🏾👍🏾👍🏾
Abraham Lopez I probably didn’t make it real clear in the video but should have, that I ended up using a regular mil-spec spring instead of an extra power spring. The mod I was doing to my firing pin is the same as an enhanced firing pin to the best of my knowledge. And I definitely considered running that nickel boron carrier with my bolt. I’m going to run the carrier I have for a while and check it for unusual wear. I want to sell the nickel boron one and if I can get more for than what my current BCG cost I’ll be able to reduce my overall build price, which is always one of my goals 👍🏻Hopefully I’ll be able to post an update video soon with hunting footage within the next month🤞🏼
Cumberland Gap Tactical awesome. I love doing budget builds. I just finished my x39. I went with a sidecharge so it up there compared to my other budget build but I have been wanting one so I figured I would go for it. Looks like you got a good setup. Can’t wait to see more updates
Yea Jordan would like to see the hunting video. You make a lot of sense talking about selling the one bolt to bring price down. I have to start thinking that way. One of my biggest problems is when I buy parts for my guns,I always say I will sell old. But I can never let anything go. I'm a hoarder when it comes to gun parts and it's not like I have money to spare. I have to get over this bad habit.
I totally understand brother. And even being in the firearms business it sounds logical to keep “extra parts” but if those parts are worth money you need to move them to keep cash flow coming. The same idea is true for the average gun guy. If you ain’t using that junk get rid of it to buy things that you’ll get more use/enjoyment out of. It takes time to get into that mindset. BTW I wish I had better footage of the deer I killed with my 7.62 AR but it really wasn’t worth watching lol. And I currently traded that gun for a brand new set of 35’s for my truck 😂
Ks47 gen2 runs like a dream with any ammo
1st video I've seen of yours and I am subscribed now!
THAT BOOSTED GUY much appreciated! There’s a lot more content to come!
@@tristarcustoms77 same here, I'll have a new video of shooting a pmr30 uploaded shortly! .22mag/flamethrower lol.
What Ive found with building ARs in x39, the Rock River Arms National Match 3.5lb 2 stage trigger feels great and has given me great results with primer strikes. They do sell a red, heavy hammer spring, for 2 bucks that will ignite the hardest of mil-surp primers.
Erik Tuss awesome thanks for the info! What’s the price on that trigger set up?
@@tristarcustoms77 the trigger can be found for $80. Its regularly on sale from places like Right to Bear or Primary Arms. Any more, that trigger, TC bcg, and CPD mags are a staple for x39 builds.
Here in Texas I go hog hunting often. Its a great setup for that. We have a Helicopter hunt on 3/21 with everyone using ARs in x39.
@@tristarcustoms77 that trigger is on sale right now at Primary Arms for $85.
Your Lower is it polymer, Not had good luck with them. Broken two at buffer tube separation. so change back to standard. Maybe just bad quality forgot where I got them from. But works great now with a new billet lower. with the enhanced firing pin and one pin I milled both work great.
Gary Rigney yeh I would much rather have a standard lower instead of polymer. I’ll eventually change this one out. But all other ARs will be billet.
Get the enhanced firing pin or have your gun smith mill the firing pin. It will eliminate the light primer strikes.
Nice safety etiquette. You waited just in case it was a hangfire
25/1000 is too much too take off. 5/1000 is what is needed too take off buddy! Good luck and give it a try.
Thanks for the vid! I'm going to build one!!
Great video. If you had to do it again would you build another one? I am looking to build 1 in the next few weeks and would like to know if it is a keeper.
Swamppappi Outdoors oh yeh definitely! I’ve got an update video I’ll be posting real
Soon so stay tuned!!
That next video is up if you want to check it out
I checked it out, you are gonna find the right trigger. I can honestly say you never give up. Does it run fine with a mil-spec trigger and enhanced firing pin?
The Enhanced Firing Pin is a Must Have for 7.62x39 ARs if you will be shooting Steel Cased (Hard Military Primer) ammo. Try a Red-X Enhanced Firing Pin for only $10 to your door.
So if I heard you correctly, you used a standard 5.56 lower correct?
That’s correct
I used a complete psa lower with a bear creek upper on mine with AR Stoner magazines (specific to caliber). Was having a failure to fire about 1 in every 10 (shooting Tula, Wolf seemed to be a little better). Changed to enhanced titanium firing pin and it runs perfect now.
What buffer weight
Did you have to do anything to the magazine well to except the 7.62 magazine
Nope the standard AR-15 lower accepts the 7.62 magazine with zero modifications
Man you gotta go extra power extra power hammer spring . There are some things you can do to lighten that trigger pull up though.
Def wyd buy that 7.62 bolt if you would drop a price for me.
Alright, alright, alright...(sniff...)😂🤣😂 Good video, just bought the BCA 7.62×39 and am already looking for an enhanced firing pin and heavy trigger spring! Thanks for the info!
Dave Hanson how do you like the rifle? I am thiiisss close to buying one myself
@@HardHeadMilitary its difficult to get any less expensive than the BCA upper. Primary Arms has some good sales on Radical 7.62 uppers too.
Ive built several. Some have a BCA x39 barrel. At the holiday sales the barrels are $50.I also have built them with Faxon and Diamond back barrels. Faxons are the best, but are they worth 3x the cost of a BCA barrel? Maybe. Tool Craft makes a great BCG in x39 that comes with an enhanched firing pin. They run about $80. If you are really scrimping, Unbranded AR sells just the x39 bolt with enhanced pin for $40. You can drop that into any of your 556 carriers.
CPD mags are the only 28 or 30 round mags that Ive found work 100%. ASC or any other 10 rounders work fine too, but not the 30 rounders.
One thing people make a big mistake on, it is not cheaper to shoot 7.62 x 39. If anything, it is more expensive. Mags cost more, steel cased ammo prices are the same, brass is more expensive for x39 (significantly), and hunting ammo is more expensive for x39.
I think I'm gonna build one of them for hunting on the cheap. Can be one that I can beat ,take out in the weather etc. But after listening him sniff,which my wife tells me to blow my nose all the time. But now I know what it looks and sounds like on the other end. Blow your nose. I will from now on. I'm just a bit picky I guess but must be others out there too. Good video though. Gun looks fine to me
Wow I’m from Tennessee too. What part you from?
Will Morris Claiborne County.. bout an hour north of knoxville. You?
Jordan Ballew Hardeman County about an hour East of Memphis
You still got the bolt carrier up for grabs? Btw, you can pick up a 6.5 grendel barrel for like $80 + it'll run the 7.62 magazine & should run the same bolt as well (6.5g uses 7.62x39 parent case) but u can upgrade to the type2 6.5 bolt if u wish.
321JKilla that bolt carrier sold just the other day actually. And thanks for the information I might build a 6.5g upper in the future..
TNT Tactical I kno bear creek got in some trouble with ICE, but I bought a 24" stainless fluted BCA barrel in 6.5g for under $90 & use my 30rd 7.62x39 ar mag. Steel case stuff is $5/box and the hornaday black is about $1/rd but u can get 1K yd range if ur barrel is decent!
321JKilla man that’s really
Cool. Where’d you get Your barrel from.
TNT Tactical classicfirearms.com had mags for $18 & the 6.5g barrels on sale originally $119 down to $89.
Tyoe 2 grendel is the only way to go the headspace makes the 6.5 a long range precision cartridge
U still selling the bcg
Ok question I have a ks-47 PSA Hybrid upper and I got a ar 15 plumcrazyarms multi cal lower receiver laying around I put it together and I'm tryna ask is it compatible
To be honest I have do idea
@@tristarcustoms77 I appreciate it
Do you know how many lbs the trigger pull is with the mil-spec spring?
I’m not 100% google says 5.5 to 8.5 pounds. I’m gonna call this one like 6-7lb
Excellent presentation
Jordan... I fit a 7.62x39 bolt carrier group into my regular ar15 upper. Will it work?
Fel Ta yes it works with any standards AR-15 upper. Just swap out your barrel and you should be on your way.
@@tristarcustoms77 nice. This is my ar pistol it has a quick take down kit for a barrel swap. 556/300blk
@@tristarcustoms77 and now... 7.62x39 Imma buy the ar 7.62x39 mags for it too. Any recomendation?
Fel Ta the AR Stoner mags from Midway USA have worked well for me except one 30 round mag wouldn’t feed the last round in the mag
@@tristarcustoms77 great bro. Try checking the spring/follower
I love the improvised lathe, brings new meaning to "Drill Press"!🤣
Nice video I'm doing a 7.62 build also just waiting on a few more items . I was wondering did you try the enhanced firing pin I've heard its needed sometimes to fire cheap steel case ammo aka TULA looking forward to more updates
Benjamin Ledbetter if I’m not mistaken the “enhanced firing pin” is basically the same thing as the firing pin mod that I showed in the video. So that’s why I haven’t tried it but if you try it let me know what you think about it.
@@tristarcustoms77 I didn't know they were the same this is my try at the 7.62 thanks for the heads up
The enhanced pin isn't necessary for steel case hard primer stuff, just need to get the jp enhanced hammer spring, you can even use the reduced power trigger spring but need the hammer spring. $13 spring kits
Do you use the same lower as 5.56
yasel cavada yes
How much for the nickle boron bolt?
brother kasey $75
Good video, check out joe bobs outfitters trigger screw best 10$ you site ef spend
Building a ar 47 anyone know about a great barrel that shoot moa at 100yards.
Lur’King Outdoors let me know if you find one!!
Bca makes some oddly enough
Try bobbing the hammer. If you take the tail off of it you reduce the weight of the hammer itself and the lighter spring can get it moving faster. Also don’t dry fire the rifle with the upper off of it you’ll destroy your lower dude.
I like the way you think! I’ll definitely give that a shot when I get some time. And I try not to make it a habit of dry firing it like that but just did it for video purposes.
Cumberland Gap Tactical well thanks man. That was one fast reply. Have a merry Christmas.
zack mcclain merry Christmas! If you took the time to watch my video and make a sensible comment I’ll take the time to write you back is the way I look at.
Cumberland Gap Tactical will you make an update video on that hammer modification if you do it?
zack mcclain sure thing man.
What all do you need to swap out if I'm trying to convert my 556 into shooting 762?
Rex Martinez in my area you can find complete 7.62 uppers for really cheap at gun shows. That includes everything you need besides magazines. But if you just want to try to keep your hand guard that you currently have you need to buy: a barrel, gas system (most 7.62 barrels have a larger profile than a 556 setup), muzzle device, bolt carrier group (or just the bolt if you can find one). I think that’s it
@@tristarcustoms77 so a 762 mag will fit into the 556 mag well?
Rex Martinez yes
Wow that was painful,,I know that you were just checking to see if the dam thing would fire,if you are going to use it for deer hunting shouldn't you be using the ammunition that you would be hunting with? That Tula ammo is crap ! Man I made a mistake one time and got ripped off and bought 100 rounds of that Tula crap for my rifle same AR platform filled up a 30 rounder got to #10 and tossed the rest of that shit in the bushes,, out of 10 rounds 6 of them fired, basically every other round went bang,, pulled out some wolf ammo and got to 15 ,and only loaded 15 and kept them but not for my AR ,I got some fiochi (spelling?) Brass case and just felt better about it and some other brass rounds and haven't been able to make my 7.63x39 AR upper misfire again,, on my 3rd case of 1000 pretty good,,
I was hoping your range day was going to be a good day then I heard the worst word on the planet..TULA !!! I know this dude that uses Tula in his carry sidearm!! If he was a family man or had more sense I would tell his ass about that bad decision, but maybe he won't shot himself one day,lol
Never had a single issue with Tula in any of my firearms. My x39 AR loves it. Wolf is made different cartridge works with Tula being the most common for their 7.62 x 39 ammo. Tula make the 8m3 "effect" bullet. It is a very good performing bullet.
Tulammo 154sp is no freaking joke on deer.
Sword skills. :)
J.E. Taylor gotta stay focused on what matters!
@@tristarcustoms77 I agree.
Ar stoner Magazines are the best ones you can get even tho some of the reviews are shitty but ive had two 30 rounders for about 7 months an (Knock on wood) havent had a issue yet. Little tip with the mags spray some gun lube under the Sitting plate in the Magazine so the spring an plate slide easier because when i first got mine they were stiff.
An the steel Ammo doesnt work half the time because the primers are much stiff then brass rounds made in america. The steel rounds are made in Russia
enhanced firing pin is like $10
What websites did you purchase these items on?
Most parts came from midwayusa.com or TNTtac.com
You still have the bcg?
No sir. Sorry I traded it last week.
Contack me on the bolt carrier
Gene Smiley long gone man
How to make (sniff-sniff) a 7.62x39 (sniff) AR Rifle (sniff-sniff-sniff).. That FAILS! (sniff-sniff)
Stop using tulammo
We all kno they’re known for light strikes
So I've heard. I hear wolf functions a lot better only a few cents more if you buy bulk.
Please stop dry firing a separated lower 😓