Cut the tube at a 45 degree angle and cut the hole very small. Put the tube at the angle of the cut and caulk down the trim and wall. If gap is too wide on trim cut a bit more off the tube. If you do this you barely have to wipe it and it won't be too heavy and smear everywhere. I'm a painter and have done it this way for 30 years.
In case you will be painting on or around caulk, petroleum jelly is not a good idea, it will ruin your paint work, instead, use a spray soap or foam glass cleaner. Spray right over the caulk and your fingers will not pick up, but smooth the caulk. The residue will not hurt your paint work...
Not only that….he isn’t a professional…a professional will push the tube away to make a clean line, not pull it towards yourself. This is the worst caulking video I’ve ever seen!
Majstori, kada nanesete silikon na površinu, sprejerom sa mesavinom vode i tečnog sapuna, poprskajte silikon i fazoniranom plastičnom ili silikonskom špaklom skinite višak nanesenog silikona. Silikon se ne fazonira prstom
Did I miss something here? Where's the part about using a bar of soap in the silicone??????? As for the duct tap, just cut the hole smaller in the beginning.
Absolutely nothing here but on how NOT to use a caulk gun! If he came to my job and did crap like that I’d send him back to school to learn how to caulk a joint correctly. LOOK LIKE A KINDERGARTNER did everything
Why use your finger, craftsman? Everything should be done completely differently: after applying silicone, a soap solution is applied as a spray, then the seam is passed with an angular rubber patel.
Разве можно так делать? А тем более советовать делать? Я в тихом ужасе!))) Мы тоже так ладошками силикон растирали в середине 90-ых... Сейчас то уже не проблема купить(заказать) шпателей для этого дела (в том же зеленом магазине). Пальцем.... Тьфу....😅
Solche erbärmlichen Ergebnisse erzielt man, wenn man noch nie etwas von Glättmittel gehört hat. You get such pathetic results if you've never heard of smoothing agents.
Cut the tube at a 45 degree angle and cut the hole very small. Put the tube at the angle of the cut and caulk down the trim and wall. If gap is too wide on trim cut a bit more off the tube. If you do this you barely have to wipe it and it won't be too heavy and smear everywhere. I'm a painter and have done it this way for 30 years.
Suicide not allowed
So should I put some soap in my silicone or what?👍
Where’s the soap?
비누물 사용하란거지 주로 퐁퐁물
В названии ролика)))
İts old and end😅😅
Came to ask the same too. Misleading title. I want my 4 minutes and 11 seconds back 😝
On the finger.
Very nice but where is the soap why video title different than content??!!
In case you will be painting on or around caulk, petroleum jelly is not a good idea, it will ruin your paint work, instead, use a spray soap or foam glass cleaner. Spray right over the caulk and your fingers will not pick up, but smooth the caulk. The residue will not hurt your paint work...
Suicide not allowed
No puedo dejar de ver estos videos. Para peor mañana no me acuerdo ni la mitad pero que buenos trucos!
So good I like video I come from Thailand 🇹🇭
A light spray of detergent water on the beading works well.
Suicide not allowed
Кто нибудь скажите ему что можно мыльным раствором обойтись вместо малярного скотча
Where's the bit about soap?
You should always push the nozzle along the joint, not pull it. Just dip your finger in water with fairy liquid to smooth off silicone bead.
fairy liquid ?
@@JACK-wh6jl Fairy Liquid (by Procter & Gamble) is a popular UK dish washing detergent liquid.
@@JACK-wh6jl i thought it might have been a new gender.
@@larrydickman6016suicide not allowed
@@Thedrewzzsuicide not allowed
where was the soap bar trick?
There's nothing about soap in this video. Misleading and clickbait
🔥
Oo
O
Doch, er hat seinen Finger damit eingeschmiert als Trennmittel...das Seifenbild ist leicht irre führend...
Not only that….he isn’t a professional…a professional will push the tube away to make a clean line, not pull it towards yourself. This is the worst caulking video I’ve ever seen!
Majstori, kada nanesete silikon na površinu, sprejerom sa mesavinom vode i tečnog sapuna, poprskajte silikon i fazoniranom plastičnom ili silikonskom špaklom skinite višak nanesenog silikona. Silikon se ne fazonira prstom
Thanks for this !
Suicide not allowed
Thanks 😊
Можно еще кембрик термоусадочный применить.
He obviously put the bar of soap where the sun doesn't shine.
Suicide not allowed
Not only do I get helpful tips, I get to giggle at the "no no" finger.
Suicide not allowed
Don't see anyone mentioning that you need to check the label because some require to be left as a bead and some needs to be smoothed down.
Suicide not allowed
Thank you for making these videos.
Donde está el jabón?
Suicide not allowed
Какой интересный эксперимент👍
Sabun nerede haci?
Use soap water instead, this is not the way of doing it. It's not just the finger that has to be soaked, also the joining angles.
Suicide not allowed
Your video is great! Thank you!
Suicide not allowed
Did I miss something here? Where's the part about using a bar of soap in the silicone??????? As for the duct tap, just cut the hole smaller in the beginning.
Dipping your finger in a mix of water and washing liquid does the same job with virtually no residue
Absolutely nothing here but on how NOT to use a caulk gun! If he came to my job and did crap like that I’d send him back to school to learn how to caulk a joint correctly. LOOK LIKE A KINDERGARTNER did everything
Suicide not allowed
Never saw an explanation about a soap bar. Click bait, I bit. Thumbs down
Very smart thanks sharing
Suicide not allowed
Ehm, where is the soap bar mentioned in the title? Clickbait alert!
sabun bunun neresinde . ?
Why use your finger, craftsman? Everything should be done completely differently: after applying silicone, a soap solution is applied as a spray, then the seam is passed with an angular rubber patel.
Suicide not allowed
Donde está el jabón?
Спасибо.
I really can't watch this anymore,there are more practical ways to do this on a better professional result
А я просто водой😉 и тот же результат... Главное контролировать заполнение щели и не надо лишнее... выбрасывать
تسلم يامعلم
Отрезать носик полностью, а потом обмотать скотчем для уменьшения носика! Логика!
He used vaseline on his finger and no soap at all! He should rectify the catch title.
I get really annoyed by finger wagging.
Waar is de zeep?🤔🥺😭
There’s no need to silicone up like this, cut a smaller angle on your nozzle and don’t squeeze the handle like a madman
А мыло он наверное на пол уронил, думаю догадались, что произошло дальше.
Потому сюжет где должно быть мыло отсутствует)))
Разве можно так делать? А тем более советовать делать? Я в тихом ужасе!))) Мы тоже так ладошками силикон растирали в середине 90-ых... Сейчас то уже не проблема купить(заказать) шпателей для этого дела (в том же зеленом магазине).
Пальцем....
Тьфу....😅
Не вздумайте воспользоваться советами этого штукатура...
Just a goober who gobs caulking
Super Like
👏👏👏👏👏👏👏👏
А где мыло???!!!
Süper .
Click Bait soap. But still, some good hacks.
ممتاز
Может ещё сомлями.или ещё чем умник какой обрезал теперь латает
මරැ අදහස මරේ මරැ
Ridiculous
MENSO
Yeah, wtf?
Only 1 good idea in this video. The rest are garbage. Good idea = duct tape to narrow nozzle.
Дичайший бред!
👍👌👏✊🤜🤛🤝
Что он хотел этим показать
Nothing for me here….
Zeit Verschwendung.... aber lustig🤣🤣🤣
👍
О брат ты супер умный
😅
Video acchiappa clik
il sapone non c'entra nulla. Forse l' acqua saponata.......
Ma devi essere più serio 👎
Solche erbärmlichen Ergebnisse erzielt man, wenn man noch nie etwas von Glättmittel gehört hat.
You get such pathetic results if you've never heard of smoothing agents.
Ну ти і село!
This is nonsense
Колхоз! Ничего полезного не увиде
смочи мыльным раствором и всё
👏👏😂😂😍
бред дич полная
And the soap is... nowhere in this video. You are a liar my friend.
Clickbait ! I won't be watching anymore of your videos . Unsubscribed
amater
Блин! А где мыло ?