pardon my french but no mother fucking way, ive had this thing for months and was convinced i fucked it up, turns out i was calibrating it completely wrong. Thank you very much
Why didn't you say or show that it can also be controlled using the controller that is included in the set? You only showed using the app on your phone and computer, but not using the remote control. Why?
I know this project was done a couple years back but is there any update to the code since? And my remote never work as supposed to work for 1 minute intervals then it get disconnected from exapod.
You can download the latest code and tutorial with this link: github.com/Freenove/Freenove_Hexapod_Robot_Kit/archive/master.zip If the issue remains, please send a video to show that to support@freenove.com? We will check and offer solutions.
When I put the batteries in it says 0.30V on the application, not 8.0V, any idea on what might be doing wrong please? I'm using 3.7V 14500 batteries as instructed in the tutorial
Just bought mine with a v3 labeled board i know it says door use button batterys but would it still function with button batterys? (Have a pair of button batterys on hand)
@@Freenove one other minuscule question about batterys can the batteries charge in the robot itself (obviously after finishing the assembly) or do you physically need to take them out for charging
Pretty sure you can just make a side program that makes input of colours on RGB sensor turn on and off a output depending on the colour and same for the ultrasonic sensor
I’m back again and got my port working, but when I insert the zip library’s to Arduino, it says there is a error and won’t let me verify. Also Processing isn’t working is there a link I can use?
@@Freenove i got 1 and i didnt do the legs as 90 Degrees is there a way to Un Screw them and move it without taking them apart Fully? also is the ESP8266 needed for full functionality over code?
i got this error while trying to connect to the after running the processing thing and clicking connect on "control" 14:43:40 Serial connection attempt: COM1... 14:43:43 Serial read failed: time out 14:43:43 Serial connection failed: detected serial, no serial responded
COM1 is not the correct port. Did you upload the default code? Would you mind sending an email to our support at support@freenove.com? Our support team will help you. Many thanks.
4 servo are bad what tipe of servo I can use. My email was rejected by your mailbox. Please tell me more details. How did you test them? We can send new servos for you. Please provide your information for shipping. *Name: *Address1: Address2: *City: *Region: *Post Code: *Country: Phone Number:
it is telling me Arduino: 1.8.19 (Windows 10), Board: "Arduino Mega or Mega 2560, ATmega2560 (Mega 2560)" Sketch uses 1536 bytes (0%) of program storage space. Maximum is 253952 bytes. Global variables use 9 bytes (0%) of dynamic memory, leaving 8183 bytes for local variables. Maximum is 8192 bytes. An error occurred while uploading the sketch This report would have more information with "Show verbose output during compilation" option enabled in File -> Preferences. Why is that? I am on the LED part of the tutorial
I cannot use to upload because it says Arduino: 1.8.16 (Windows 10), Board: "Arduino Mega or Mega 2560, ATmega2560 (Mega 2560)" Robot:19:10: fatal error: FNHR.h: No such file or directory #include ^~~~~~~~ compilation terminated. exit status 1 FNHR.h: No such file or directory The problem is that I have a file called "FNHR.h" on my Pc, I don't know why Arduiono cannot find it or ignores it. Can you help me?
honestly amazing, the support team is fantastic and deserves a pay raise.
Many thanks for your comment.😊
what type of material we can use for making it in low cost can you suggest something???????????????????????
Now we use acrylic, which is in low cost for DIY.
does it come with the cable u showed in the vido if it dose not can u tell me exactly what cable i need for ti to connect to my pc.
can i assemble without batteries? i dont have them yet...
pardon my french but no mother fucking way, ive had this thing for months and was convinced i fucked it up, turns out i was calibrating it completely wrong. Thank you very much
Why didn't you say or show that it can also be controlled using the controller that is included in the set?
You only showed using the app on your phone and computer, but not using the remote control. Why?
For the usage of the remote controller, please refer to this video. ruclips.net/video/nivTZeGthf4/видео.html
Awesome 👍 looks much more like a spider than my robot
Thank you! :-D
every thing went cool but when calibration stage started there was no values.
what should i do. might be ny error.
I know this project was done a couple years back but is there any update to the code since? And my remote never work as supposed to work for 1 minute intervals then it get disconnected from exapod.
You can download the latest code and tutorial with this link:
github.com/Freenove/Freenove_Hexapod_Robot_Kit/archive/master.zip
If the issue remains, please send a video to show that to support@freenove.com? We will check and offer solutions.
When I put the batteries in it says 0.30V on the application, not 8.0V, any idea on what might be doing wrong please? I'm using 3.7V 14500 batteries as instructed in the tutorial
Please send your battery link to support@freenove.com
it said3.7 18650 batteries
The shipping fee is so high we can get the acrylic body design so we can create one
It says I have to add the ControlP5 libraries?
The robot leg is moving in random direction and when i switch on it didn't move to destined position but it. Was moving towards one side
Dear customer, could you please send us a video and the link of battery to support@freenove.com?
Just bought mine with a v3 labeled board i know it says door use button batterys but would it still function with button batterys?
(Have a pair of button batterys on hand)
Sorry but no, button top batteries are too long to fit in.
@@Freenove one other minuscule question about batterys can the batteries charge in the robot itself (obviously after finishing the assembly) or do you physically need to take them out for charging
@@Thetitaniumsteppermotor You need to take them out for charging.
Do you need to use every screw that is in the package, or are there some extras?
There are spare screws.
@@Freenove Okay, thank you!
is it normal that capacitors are very hot when I turn on the robot ?
It's not normal. Please send an email to support@freenove.com. Our support team will help you.
How to add a ultrasonic sensor and a rgb sensor? can you make a video about this please.
Pretty sure you can just make a side program that makes input of colours on RGB sensor turn on and off a output depending on the colour and same for the ultrasonic sensor
I’m back again and got my port working, but when I insert the zip library’s to Arduino, it says there is a error and won’t let me verify. Also Processing isn’t working is there a link I can use?
Please send screenshots of the error message to our support. Our support team will help you.
I have no port and my computer management page also has no port, what do I do?
Please follow the tutorial to install the ch340 driver and try again. If the issue remains, please email our support team at support@freenove.com.
Do you need a Arduino or Pi for this to work and dose it come with the main processing board
No you don't need. It comes with the main board.
@@Freenove i got 1 and i didnt do the legs as 90 Degrees is there a way to Un Screw them and move it without taking them apart Fully? also is the ESP8266 needed for full functionality over code?
@@jafjay6024 Could you please contact us via support@freenove.com? We will offer you solution.
@@Freenove ok thank you love the kit so far
if i would start the processing, (ore communicate, controll) App, arduino says "ControlRobot is not the name of a type" how can i fix this pls help
Did you unzip the whole resource? You can contact us via support@freenove.com with more details.
i got this error while trying to connect to the after running the processing thing and clicking connect on "control"
14:43:40 Serial connection attempt: COM1...
14:43:43 Serial read failed: time out
14:43:43 Serial connection failed: detected serial, no serial responded
COM1 is not the correct port. Did you upload the default code? Would you mind sending an email to our support at support@freenove.com? Our support team will help you. Many thanks.
@@Freenove I'll email, thank you.
WHY DOSE IT SAY THIS CLASS "CONTROL ROBOT" DOES NOT EXIST.
SARRY I HAD CAPS LOCK ON😅
Would you mind sending us a video to show the operation process? Our support team will help you.
can use arduino uno and COM3?
The control board is based on arduino mega. It cannot be replaced by Arduino UNO.
How do you connect it to the remote controller?
Hi! We will make a video about that.
Yesss, I can’t wait, thank you so much
@@amenhika9771 Hi, we've uploaded the tutorial for using the remote controller. Here is the link: ruclips.net/video/fK7IHMA60F4/видео.html
What size of servo it is
Its size is same to ES08MA-Metal-Analog-Servo-Model:
www.amazon.com/ES08MA-Metal-Analog-Servo-Model/dp/B07KYK9N1G/
Hello, we also reply your email. But it is returned by your mail. I don't know why.
4 servo are bad what tipe of servo I can use.
My email was rejected by your mailbox.
Please tell me more details. How did you test them?
We can send new servos for you.
Please provide your information for shipping.
*Name:
*Address1:
Address2:
*City:
*Region:
*Post Code:
*Country:
Phone Number:
The Processing app tells me that they cant finde a type of named "controlrobot" need some help pls
Hi! Would you mind sending an email to our support at support@freenove.com? Many thanks.
@@Freenove thanks i try it
@@Freenove Hey me again my mailbrowser tells me that the adress is not found
@@kaarmaxd1394 Sorry, it is support@freenove.com.
@@Freenove Okay thank you and no problem
Can I use the code with my hexapod even if it's not from freenove?
It may work if your hexapod robot uses mega 2560.
@@Freenove can I use a ps2 controller for this?
@@lloydagonia2284 It may work, but you need to write code yourself.
@@Freenove Hey which pins did you use for the ESP8266 module ???
@@lloydagonia2284You can find the schematic here:
Freenove_Hexapod_Robot_Kit\Hardware
it is telling me
Arduino: 1.8.19 (Windows 10), Board: "Arduino Mega or Mega 2560, ATmega2560 (Mega 2560)"
Sketch uses 1536 bytes (0%) of program storage space. Maximum is 253952 bytes.
Global variables use 9 bytes (0%) of dynamic memory, leaving 8183 bytes for local variables. Maximum is 8192 bytes.
An error occurred while uploading the sketch
This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.
Why is that? I am on the LED part of the tutorial
I am on the Blink I mean
@@readdrawsy4728 Would you mind sending us a email at support@freenove.com?
Do I need the files to code the bot
Yes, you can download them with this link: github.com/Freenove/Freenove_Hexapod_Robot_Kit/archive/master.zip
I cannot use to upload because it says
Arduino: 1.8.16 (Windows 10), Board: "Arduino Mega or Mega 2560, ATmega2560 (Mega 2560)"
Robot:19:10: fatal error: FNHR.h: No such file or directory
#include
^~~~~~~~
compilation terminated.
exit status 1
FNHR.h: No such file or directory
The problem is that I have a file called "FNHR.h" on my Pc, I don't know why Arduiono cannot find it or ignores it.
Can you help me?
unable to open arduino on chrome os
Please try it on Windows or Mac. We don't have chrome OS to try.
Yeah im lost trying to program the robot
@@fknkat378 We don't have chrome OS to try. What can I help you? Please tell me more details.