Thanks for the video. My mom has this generator and it stopped working. Her generators float had gas in it. If not for your video I would have not have known to check for that. I was gonna just get just the kit, which doesn't include a new float. I found the entire replacement carb on Amazon for about $30.
Thank You for the instructional clip. I had the same problem brand new gen used for about an hour then stored for 2 years. Took 3 times to figure out my float had a hole in it. i took a tiny drill bit drilled a hole where i could blow through it, found the original hole near the bracket mount soldered it all up and good to go.....hopefully....still have to assemble it.....thanks again
I wish you were my neighbor so you could help me!!! Lol... But thanks to your video I think I might actually be able to do it. You're awesome and so is your video. I've been looking every for help and this is the first time I haven't wanted to throw the damn thing and give up! So thanks again!
Excellent video. Thanks for sharing. I have same generator which had the same problem. Was able to getting it running by cleaning the carb but not taking it completely off to do a rebuild. It runs good now but stumbles every 10 seconds or so. I just might get the kit now. I wish you showed your gen running tho because I wanted to see how she ran after you put in the new kit. If you can post a quick vid, that would be great. Thanks again.
Nice Video, clear with good camera angles. I hope I can duplicate your skills and get this thing up an running again, otherwise it will be a great tent weight.
The one part of this video that I needed was how to put the Needle back in and just as you begin to put the needle back in you change to a different scene where you’re done putting it back in
Sorry... The part I passed over was mounting the needle onto the float which is just a matter of putting the spring into the little holes. Then, inserting the needle into the hole is shown in the following clip.
That repair you using does fits my power mate 6250 generator 10ph tecumseh because my I loss my float needle o ring if so send me the part number and where to buy it
Thanks for the video. My mom has this generator and it stopped working. Her generators float had gas in it. If not for your video I would have not have known to check for that. I was gonna just get just the kit, which doesn't include a new float. I found the entire replacement carb on Amazon for about $30.
Thank You for the instructional clip. I had the same problem brand new gen used for about an hour then stored for 2 years. Took 3 times to figure out my float had a hole in it. i took a tiny drill bit drilled a hole where i could blow through it, found the original hole near the bracket mount soldered it all up and good to go.....hopefully....still have to assemble it.....thanks again
This video was a very BIG help and Thank you for making it.
I wish you were my neighbor so you could help me!!! Lol... But thanks to your video I think I might actually be able to do it. You're awesome and so is your video. I've been looking every for help and this is the first time I haven't wanted to throw the damn thing and give up! So thanks again!
Excellent video. Thanks for sharing. I have same generator which had the same problem. Was able to getting it running by cleaning the carb but not taking it completely off to do a rebuild. It runs good now but stumbles every 10 seconds or so. I just might get the kit now. I wish you showed your gen running tho because I wanted to see how she ran after you put in the new kit. If you can post a quick vid, that would be great. Thanks again.
You forgot the emulsion tube, which are normally plugged if gas has gone bad, the tiny o rings on them also deteriorate quickly as well.
Nice Video, clear with good camera angles. I hope I can duplicate your skills and get this thing up an running again, otherwise it will be a great tent weight.
oh leave him alone. He had the best vid on here good camera angles good lighting etc..
Glad you got it going
The one part of this video that I needed was how to put the Needle back in and just as you begin to put the needle back in you change to a different scene where you’re done putting it back in
Sorry... The part I passed over was mounting the needle onto the float which is just a matter of putting the spring into the little holes. Then, inserting the needle into the hole is shown in the following clip.
thanks a lot for the video
I didn't see you set the float level before you reassembled the carb.
Good video - did you have luck setting the valve seat correctly with the Philips screwdriver? - which you called a gasket.
I was a bit nervous making the video. Yes. I had luck.
I noticed that too.
That repair you using does fits my power mate 6250 generator 10ph tecumseh because my I loss my float needle o ring if so send me the part number and where to buy it
If you don't thoroughly clean the idle jet, especially the microscopic orifice in the tip, the engine will never run correctly. Don't ask how I know.
Why does gas run threw carb when motor doest run