Sir while you were doing cylinder cut out procedure, I was also looking at their delivered fuel volume. Aren't they too high reaching 50+? Just replacing
fuel pressure depending on the pump output pressure they must be reach the minimum pressure or else the is hard starting, sometime not possible to start, if you think that the pressure shows on my video, the system they have a program that they automatical trim the pressure depend on the trimp program setup by the caterpillar.
@@caterpillarjhunhunk CAT ET is limited cannot clear DPF codes here. I am buying one . I have a " Candoo" cheap one does basic scans on CAt ,Cummins Volvo.
Sir catterpillar c9 engine did not take throttle.. only run idle rpm (800) we check engine display.. error (840, or 802) show... then i check the detail of this error is (input incorrect).. please tell me the what's the problem???
bro try to check the solenoid at the control valve, or you can try actual test of lever control to exchange arm control to bucket control, if the arm control are working to bucket it means solenoid damage or wiring harnes
Can you help me… we start engine normal. After 30sec motor temp goes to max power drop and machine loss energy …. And goes off …. And again, again the same…. Maybe wiers,procesor what ?
Good job master...
sir , how to caterpillar et please make the one video
Sir gd morning ung cat 950H nmin,after kinabit ang injection pump,umandar nman kaso kng may load mahina ang power nya..
well done
Good job brother
thanks bro
Sir while you were doing cylinder cut out procedure, I was also looking at their delivered fuel volume. Aren't they too high reaching 50+? Just replacing
fuel pressure depending on the pump output pressure they must be reach the minimum pressure or else the is hard starting, sometime not possible to start, if you think that the pressure shows on my video, the system they have a program that they automatical trim the pressure depend on the trimp program setup by the caterpillar.
Sir tnx for sharing
welcome
How to check transmission oil pressure and to improve the pressure.
Every machine have the testing port or plug to check the pressure
Check the gear pump pressure, make it sure that the pressure is in normal, before you are going to proceed at solenoid valve gear selector
Good morning sir
yes sir this my whatsapp +971567581176
Is that CAT ET or a dealer level computer scanner?
Excellent work Akhi.
Salaaam
CAT ET bro
@@caterpillarjhunhunk CAT ET is limited cannot clear DPF codes here. I am buying one .
I have a " Candoo" cheap one does basic scans on CAt ,Cummins Volvo.
@@MitzvosGolem1 actualy bro i am using CAT ET we got it from cat dealer
Sir catterpillar c9 engine did not take throttle.. only run idle rpm (800) we check engine display.. error (840, or 802) show... then i check the detail of this error is (input incorrect).. please tell me the what's the problem???
this engine what type of machine used
Its power pack pennine.. which use on stone columns
@@imran3055 can you send me the pic of monitor and some details in my whatsapp +971567581176
@@caterpillarjhunhunk ok
Pashout chief
sige wait mo lang s next video ko
Sir if I need your help would you do thank you sir
your very welcome sir whats app +971567581176
Sir 950H caterpilar arm not going down
bro try to check the solenoid at the control valve, or you can try actual test of lever control to exchange arm control to bucket control, if the arm control are working to bucket it means solenoid damage or wiring harnes
Hi sir I ask you about low power problem caterpillar wheel loader 950 I can you help me sir thank you
can you pls give the details of the exact problem or contac me in my whatsapp+971567581176
Can you help me… we start engine normal. After 30sec motor temp goes to max power drop and machine loss energy …. And goes off …. And again, again the same…. Maybe wiers,procesor what ?
Ano facebook page nyo sir?
Broo may email add ka,pwde ba kita macontact slmat
yea sir jhunlambino27@yahoo.com
whatsapp +971567581176