Regarding your remote control. the 2.4 GHz signal won´t be able to penetrate the water down very far because of the short wavelenght. That is why most model submarines use 40 MHz transmitters and receivers (35MHz in the US), are you planning on running an antenna up the periscope, so you always will have something above the waterline (and sail at periscope depth)?
Hello in the entire ballast operating system because I am a bit lost in assembling the more electric water pumps because all the submarine and in 3d printing
Hello! I was thinking of printing your submarine, but I can't find a A2215 motor anywhere in Europe, will an A2212 1400kv work? If not can you reccomend a more common motor to use
okej nice 👍 What size are you usingWater Tight Cylinders , id od ?started printing last week, very kind of you to answer my questions We’ll catch up later 🤗
Hello again 🤗 I wonder if you use all parts in the list🤔 I can't quite get it together ,do i have to change the scale or something ? looking forward next movie
okej nice 👍 What size are you usingWater Tight Cylinders , id od ?started printing last week, very kind of you to answer my questions We’ll catch up later 🤗
Hello again 🤗 I wonder if you use all parts in the list🤔 I can't quite get it together ,do i have to change the scale or something ? looking forward next movie
@@Mr.RC-Creatorhello mr what did you have a video for the complete assembly of the submarine is the diagram of the electrical connection please because I am lost to suck up the water we send to the side of the hull or not
Can you pls explain the ballast tank system with these two pumps and their piping i am a bit confused pls explaine
The first pump will suck water into the tank, while the second pump will suck water out of the tank and must have a ventilation line as well.
un trabajo espectacular. necesito saber lo que sigue, aun no tienes el video hecho de la siguiente parte?
esperamos tus noticias. un saludo.
Gracias por ver mi vídeo. Intentaré terminar el último paso. Muchas gracias.🙂
Regarding your remote control. the 2.4 GHz signal won´t be able to penetrate the water down very far because of the short wavelenght. That is why most model submarines use 40 MHz transmitters and receivers (35MHz in the US), are you planning on running an antenna up the periscope, so you always will have something above the waterline (and sail at periscope depth)?
Thank you so much for your advice. I now have two options, 2.4 Ghz and 900 Mhz.
можна використати поплавок, щось типу того які ставлять на насоси, тоді радіомодуль теоретично увесь час буде на поверхні
@Глеб-й8у Thanks. ,,, 🙂
I am wondering where the air gets filled up when the submarine is inside the water.
You mean the ventilation pipe? I have one ventilation pipe.
Hello, Bro !
Thanks for movies. Why you use two engines ?
To have enough weight to make the boat dive
Hello in the entire ballast operating system because I am a bit lost in assembling the more electric water pumps
because all the submarine and in 3d printing
@@dimitrybattesti7930 Hello tell me your little problem.
@@Mr.RC-Creator hello know to know camp you will make the next video for the complete assembly of the submarine to understand better please
@@dimitrybattesti7930 Thanks for following me.
How long is the drive shaft when you use it?
Drive shaft Long 25 cm. 🙂
Hello! I was thinking of printing your submarine, but I can't find a A2215 motor anywhere in Europe, will an A2212 1400kv work? If not can you reccomend a more common motor to use
@Mihai You can use it.🙂
Water might swoosh around in the tank causing the sub to lose balance. To fix the try adding a few compartments in the tank.
I am so very grateful for your guidance,
okej nice 👍 What size are you usingWater Tight Cylinders , id od ?started printing last week, very kind of you to answer my questions We’ll catch up later 🤗
I usingWater cylinder size od 70mm id 66mm thickness 2mm length 95cm.
Hello again 🤗 I wonder if you use all parts in the list🤔 I can't quite get it together ,do i have to change the scale or something ? looking forward next movie
No!!! you don't need to change the scale of anything.,😁
okej nice 👍 What size are you usingWater Tight Cylinders , id od ?started printing last week, very kind of you to answer my questions We’ll catch up later 🤗
do you have a link for all the electronics? it would make it a lot easier on all of us haha
th.aliexpress.com/item/2251832776618851.html?spm=a2g0o.productlist.main.17.425aN2QFN2QFLF&algo_pvid=815c3e8c-3649-4d21-b10a-b7363246b031&algo_exp_id=815c3e8c-3649-4d21-b10a-b7363246b031-8&pdp_npi=4%40dis%21USD%215.84%212.92%21%21%215.84%212.92%21%402101fb1417194955533395758ea70d%2166536458020%21sea%21US%21173671390%21&curPageLogUid=ZBeeNTc8k0WH&utparam-url=scene%3Asearch%7Cquery_from%3A
th.aliexpress.com/item/2251801740238717.html?spm=a2g0o.productlist.main.11.6c157a49wSMqKO&algo_pvid=4b1f5d00-e398-4fe3-830d-09af4e594222&algo_exp_id=4b1f5d00-e398-4fe3-830d-09af4e594222-5&pdp_npi=4%40dis%21USD%211.27%210.77%21%21%211.27%210.77%21%402101fb1417194956036676643ea70d%2166559951354%21sea%21US%21173671390%21&curPageLogUid=spZQRIQ3oWbw&utparam-url=scene%3Asearch%7Cquery_from%3A
Nice job! I was trying to make one myself. Care to share a parts list?? Or your WTC inner part files??
But wait, there's more!😁
www.thingiverse.com/thing:5751042/files
@@Mr.RC-Creator thank you. Would you send me the prop file?? 🙏
@@marchill256 Try again.😁 www.thingiverse.com/thing:5751042
hello 🤗how's it going with submarine I'm curious warm greetings frome sweden
Wait a little longer.🙂
Hello again 🤗 I wonder if you use all parts in the list🤔 I can't quite get it together ,do i have to change the scale or something ? looking forward next movie
What 3-D Printer do you use?
I use 3d printer Biqu b1.😁
Hello mate . The site is down ... Please can You upload again ... Thank You
@MARISU Petch www.thingiverse.com/thing:5751042
Why not use a single reversible pump like a gear type instead of 2 one way pumps?
I use this type of pump because it can suck water quickly and have a lot of suction power, even with a long water pipe.
@@Mr.RC-Creator point taken.
@@coast219 Thanks.😊
Any updates on your sub?
@@coast219 Not yet.😅
Mantap
Thanks.😁
@@Mr.RC-Creatorhello mr what did you have a video for the complete assembly of the submarine is the diagram of the electrical connection please because I am lost to suck up the water we send to the side of the hull or not
@@dimitrybattesti7930 I’m sorry for the late reply The water pipe has two pipes: suck in and drain, and the other pipe is a ventilation pipe.
@@Mr.RC-Creator je comprends pas
hai do you have the wiring diagram?
I didn't take a picture, but they are along the cylinder.
what is the total weight of 3d printer parts?
Around 200 grams
@@Mr.RC-Creator Really? okay thank you
@@anas_kun4440 Yes! really printed with PLA material, making it lightweight.
@@Mr.RC-Creator By the way, what size tube is that at the end of the video?
@@anas_kun4440 size tube 6mm
i would like the stl files but they wont come up on thingiverse says 404 awesome video thanks
www.thingiverse.com/thing:5751042/files
where can i get the files? i am getting a 404 error
Try again www.thingiverse.com/thing:5751042
Any updates?
Not yet ! Thanks, keep up.🙂
It's been 10 months, any updates?
Cho tôi xin file STL, cảm ơn bạn.
www.thingiverse.com/thing:5845360
Great job!
Thanks.😊
Is the tank closed or vented?
@@coast219There is a vented pipe for close tank.😁
extraordinarily👌👏👏👏 when are you going to finish the rest of the files ? once again magnificent work
@@bananaman5653 I'm looking for a place to enter the water of a submarine.😅