Видео

Im so sorry. I did not do it.😉

I think there might be.

www.thingiverse.com/thing:3534935

Thank you Bro😊

Thank you Very much ! www.thingiverse.com/thing:6754528

@@Mr.RC-Creator Merci beaucoup.

Thanks. !😊

Thank you for your advice.🙂

th.aliexpress.com/item/1005006743336722.html?spm=a2g0o.productlist.main.9.109anEGfnEGfOX&algo_pvid=458dd84d-b365-4d9e-8031-2d1ec0856300&algo_exp_id=458dd84d-b365-4d9e-8031-2d1ec0856300-4&pdp_npi=4%40dis%21THB%21478.93%21462.65%21%21%2197.06%2193.76%21%40213be1e417251996707556973e8806%2112000038160875587%21sea%21TH%21173671390%21X&curPageLogUid=T2NmoLOfJ2Bi&utparam-url=scene%3Asearch%7Cquery_from%3A

😂

To have enough weight to make the boat dive

Thanks! 😁

Thanks.😁

Thanks.! 😁Try running the cooling system lines to see if they are reversed? Normally they must go in the same direction.

@@Mr.RC-Creator Hey thanks. Not sure I understand what you mean. I can simplify the problem... if I just connect a tube to the rear inlet on the water jet... no water comes out. And if I put the other end of the tube in the water, water will flow from the end of the tube to the water jet. As if the jet has negative pressure which doesn't make sense. Other than that the boat seems to work great (I did check reversing the motor direction). I'll try and get a video to share...

@@Mr.RC-Creator I was about to make a video when I think I figured it out! The prop is way back, after the inlet. So the inlet is on the low pressure side and hence it pulls instead of pushing! I'll either need a new shaft or will move the intake outside the boat body to draw water from after the prop. Mystery solved!

@@crashsquared Wow, great! Great! You are so good at solving that problem yourself.🥰

@@crashsquaredThat's awesome!

Wire connected the positive and negative wires to the charging module by connecting them to the positive and negative terminals of the battery.

@@Mr.RC-Creator So two wires connected to the positive and negative terminals of the circuit as well as the two connected to the fan? Meaning 2 wires per terminal, one for wire and one for charging module?

@@TheFreshCookies0 Yes, it's like a video clip.

555 ขอบคุณครับลำอะไรเราก็ต้องนิ่งๆ แหละ พลาดแว้ปเดียว เป็นปุ๋ยแน่ ครับ ... ไหนจะลม ไหนจะอุปกรณ์ ขัดข้อง ไหนจะคลื่นวิทยุอีก ปัจจัยภายนอกอื่นๆด้วย

I don't sell that here./It mainly depends on the power kit you use as to what size propeller is appropriate.

Thanks!. 😊

Thank you so much! www.cgtrader.com/3d-print-models/hobby-diy/other/m-jet-sprint-3d-printable-rc-jetsprint-boat-model

Thanks. Bro The motor I use is not very hot, so I don't use water cooling for the motor. But if my bro wants to use water cooling, that's fine. See the link below. th.aliexpress.com/i/32471568638.html?gatewayAdapt=glo2tha

Thanks. It uses a brushless motor.

I didn't take a picture, but they are along the cylinder.

O3 air units It doesn't work with the goggles 3 yet, wait for new firmware from DJI that supports O3. The orange is just a dust cover for the motors, it does not affect the flight.

Thanks! bro 😊

@@Mr.RC-Creator nice that you still look in the comments after a whole year

@@FIashOOT Thanks very much for the follow up.

I using batteries 11.1V🙂

Spec. Motor 3400kv. Propeller 40-41 Lipo Batt 4000-5500mha ESC 120a Seaking Drive shaft 4.mm Have fan.🙂

Thank you so much!😊.

Thanks for all the feedback. I use all those shared files as well. There might be some distortion from printing. I really apologize.

@@Mr.RC-Creator It's NOT distortion. This design is USELESS! The Motor mount is too wide to fit between the tower guards, the Propeller cage designed for another boat,....Did you take someone else's design and mix it with your own? There is absolutely no thought put into this piece of garbage.

​@@illwind9429calm down

This motor 3200kv used 2S lipo battery it will not be hot.

These boats are racing boats and they have a lot of speed.🙂

This is a wooden ship. I don't have the STL file.🙂

Thank you so much!🙂 i'm glad you like

I'm really sorry, I don't sell them, but you can buy them at any online store.

I changed the silicone wires just to make it easier to work with😁

facebook.com/groups/1648373528737255/user/100008912890242/

Sorry to rate reply!! you download Agianwww.thingiverse.com/thing:5938567

@@Mr.RC-Creator Thank u so much. Just in time. I was planning to do the assembly at the week end：）

www.thingiverse.com/thing:3685622/files

Thanks. 🙂

File name! Swam_boat_mount_motor_pro.

Thank you for posting the servobox.stl

ใบเดิม ครับ เพลาเปลี่ยนใหม่ให้ยาวขึ้นกว่าเดิมหน่อยนึงครับ😊 (เพลา 3มิล เรือ 2 ตอน)

@@Mr.RC-Creatorยอยพี่ใช้ขนาดเท่าไรครับ ผมขอสอบถามหน่อยพี่มีไลน์ไหมครับ

3.17*3 ครับ ขึ้นอยู่กับมอเตอร์ที่เราเลือกใช้ว่าแกร กี่มิล ครับ

If I remember correctly 9*4*9 🙂

I used PLA filament because it's easy to print and has a certain amount of strength

@@Mr.RC-Creator Cool mate, thanks for replying! Top job!

Thank you very much! the name for it. Toyota Tacoma body

@@user-rq5hg9fv5w 55555 ก็นิดนึงครับ...

It Can possible to flip!

@@Mr.RC-Creator thaks

I think it's incredible.🤩

Link www.cgtrader.com/3d-print-models/hobby-diy/other/m-jet-sprint-3d-printable-rc-jetsprint-boat-model

www.thingiverse.com/thing:4111057/files

Thank you very much! 😊

Thank you very much! 😁