Thanks for the instructional video. I managed to replace my old battery and reprogram closing limits. Thanks for saving me a call out and the hassle of getting a repair person.
I have a D5 evo motor. I have checked all the mechanical limits and followed all instructions. The magnet is also well set but when the motor starts for the first time, before it finishes the full cycle the controller goes off then restarts itself and everything starts over. Can you please assist?
I have a problem with my Motor it only works when i press the test button, when i try to set my reciever it doesnt have life does the black small cable have to not be connected anywhere
Hi there. Thanks for your query. No, the thin black cable is the antenna, and doesn't have to be connected to anything. The programming method would depend on the model of receiver/remote that you are using. Kindly give our technical support team a call on 0861 003 123 so that we can help you diagnose the problem.
Hi , I have installed a D5 Evo some time back but have had issues with the gate opening randomly on it s own. This causes problems for my security company as they are unable to access the premises via the Air Keypad ......when I activate the holiday lockout .
i installed a d5 motor for a client, it works perfect except that the gate moves too slow till it crosses the origin marker plus after opening, the gate shifts back slightly as if it wants to close again and stops. what could be the problem.
George Oduro Hello George. The gate will move slowly until it knows its position (by moving the magnet past the origin sensor), so that is normal. There could be a couple of reasons that cause it to want to move back after opening - such as detecting a collision. Please give our Technical Call Centre a call to help you identify what could be causing this. The number is +27 11 699 2481.
Hi, kindly assist. My D5 gate motor shows that it has stalled and when I try to reset the it by setting the gate limiters it says no origin found! Whats the correct procedure to unstall or reset it?
Hi Arthur. Thanks for your message. Kindly give our technical helpline a call on +27 11 699 2481 or send an email to support@centsys.com. Our knowledgeable technicians will be able to assist you with some diagnostic procedures.
hi. I have the D5 evo. I have black and red plus ground pillar light cables. I need help how to connect these cables to the controller? currently these are loose in my box and I want my pillar lights to work
+Miles Williams Hi Miles. Thanks for the comment. If you have lost the master, you need to clear the receiver's memory by bridging either J1 or J2 with the middle pin. This will delete all remote buttons. Next, press and hold the remote you wish to make the new master for approximately 5 seconds. Once you have created the new master, press and hold it again for 11 seconds, release it, and then systematically press and release each new button that you wish to learn. Alternatively, you can give our tech support team a call on 0861 003 123. They will walk you through the procedure.
Hi Iam an end user and recently installed a D5 Evo gate motor. Would you please help me with the guidelines in connecting a Commax intercom to the gate motor
Hi my master remote is working but my other remote not setting up so please can you help me to how to set up bcs I try to hold 15 sacend master remote after I am pressing normal remote but not seting up
Bonsoir j ai un problème sur mon motor centurion D5 quand j utilise mon télécommande ou le bouton Exit pour démarrer mon motor l écran affiche No limits SET
No hablo english y tengo problema con la instalacion de un motor D5 , parte y se para y el visor LCD me dice error en Fuente de Poder, Me puee ayudar alguien
tienes un problema en el cargador, posiblemente este dañado, debes reemplazarlo y listo. o tienes un cable flojo entre la fuente de poder y la tarjeta logica.
I have a electric sliding gate it works ok for about 20 times then it goes past stop sensor for no reason then I have to reset it again anybody got any ideas
Thanks for your important guide to Centurion Motor gate controller!
Installed a motor thanks to this video
Thanks for the instructional video. I managed to replace my old battery and reprogram closing limits. Thanks for saving me a call out and the hassle of getting a repair person.
Gate only opens with a remote.
Just sorted my issue....appreciate lots
Wooow.......thanks a lot🤝🏽
thanks fr the video ..gate was stuck..didnt know hw to put on manual...till now:)
It's an absolute pleasure, Dane! So glad that we could help :-).
Nice lecture, mind opening, thank you so much
great video and helpful
Nice explain
I have a D5 evo motor. I have checked all the mechanical limits and followed all instructions. The magnet is also well set but when the motor starts for the first time, before it finishes the full cycle the controller goes off then restarts itself and everything starts over. Can you please assist?
Check the battery if it's fully charged
How is the bracket fitted around the gate motor opening and closing with the key?
When gate opens it rolls off the rail and falls over , does this have to do with the settings on remote control ?
Very good detailed instructional video .
this is really good have you extended this type of gate to Africa especially to Kenya
Yes we have them in Kenya. Both swing and then slide
If the receiver dont read the transmitter on a d5 centurion gate motor. What could be the problem?
Awesome
❤
well explained
My gate motor doesn't want to go to manual D5 Centrion, even when i screw in the knot , it does not want to tighten up,
What could be the problem
Very good video.
Impressive
Awesome!
very clear
Hi. I have a problem opening the cover. It is stuck on the side of the gate and also where do I find the power switch. thanks.
hi thanks for the relpy
Hi sir I have one question if the motor not reached to moto must be what, only in the motor there's power
I have a problem with my Motor it only works when i press the test button, when i try to set my reciever it doesnt have life does the black small cable have to not be connected anywhere
Hi there. Thanks for your query. No, the thin black cable is the antenna, and doesn't have to be connected to anything. The programming method would depend on the model of receiver/remote that you are using. Kindly give our technical support team a call on 0861 003 123 so that we can help you diagnose the problem.
Ok thank you
Hi my d5 will nie oop of toe maak nie wat kan vout en waar na moet ek kyk help aseblief
Hi , I have installed a D5 Evo some time back but have had issues with the gate opening randomly on it s own. This causes problems for my security company as they are unable to access the premises via the Air Keypad ......when I activate the holiday lockout .
Thanks
i installed a d5 motor for a client, it works perfect except that the gate moves too slow till it crosses the origin marker plus after opening, the gate shifts back slightly as if it wants to close again and stops. what could be the problem.
George Oduro Hello George. The gate will move slowly until it knows its position (by moving the magnet past the origin sensor), so that is normal. There could be a couple of reasons that cause it to want to move back after opening - such as detecting a collision. Please give our Technical Call Centre a call to help you identify what could be causing this. The number is +27 11 699 2481.
CenturionSystems alright thanks.
the gate lying on motor
George Oduro send your contact
Why does the gate open half way and it stops
Good afternoon. My gate cannot find origin. What to do?
Hi, kindly assist. My D5 gate motor shows that it has stalled and when I try to reset the it by setting the gate limiters it says no origin found! Whats the correct procedure to unstall or reset it?
Hi Arthur. Thanks for your message. Kindly give our technical helpline a call on +27 11 699 2481 or send an email to support@centsys.com. Our knowledgeable technicians will be able to assist you with some diagnostic procedures.
Hi, please I will to get info about price and supply. Pepersonaltrainer or 0793775847 samuel
hi. I have the D5 evo. I have black and red plus ground pillar light cables. I need help how to connect these cables to the controller? currently these are loose in my box and I want my pillar lights to work
Why it keeps open when the program has been done it doesn't stay closed
How to check oil level on dip stick for d5.
hi . my d3 opens at the intercom inside but not with my remotes. please help
hi, I am going to build the gate but I don't know how to install opener so I need help, thanks kevin
Hi I'm an end user and wanted to know how would I go about programing new controls if I have lost my master control? Thanks
+Miles Williams Hi Miles. Thanks for the comment. If you have lost the master, you need to clear the receiver's memory by bridging either J1 or J2 with the middle pin. This will delete all remote buttons. Next, press and hold the remote you wish to make the new master for approximately 5 seconds. Once you have created the new master, press and hold it again for 11 seconds, release it, and then systematically press and release each new button that you wish to learn. Alternatively, you can give our tech support team a call on 0861 003 123. They will walk you through the procedure.
Thanks for the help. I appreciate the quick response. Will give this a shot and see
+Miles Williams Awesome! It's an absolute pleasure. Please give us a shout if you don't come right.
Hi Iam an end user and recently installed a D5 Evo gate motor. Would you please help me with the guidelines in connecting a Commax intercom to the gate motor
the motor is only closing when i press test button but not opening
Please contact our Technical Call Centre for advice on +27 11 699 2481
Installation instructions of the D3,D5 sliding gates.
5:21
Hi my master remote is working but my other remote not setting up so please can you help me to how to set up bcs I try to hold 15 sacend master remote after I am pressing normal remote but not seting up
if my master remote is missing, do i reprogram everthing? and how?
ok no problem this jumper open or dip baton 30 ascend or remote dip push
Bonsoir j ai un problème sur mon motor centurion D5 quand j utilise mon télécommande ou le bouton Exit pour démarrer mon motor l écran affiche No limits SET
hi i am Theo instruggle I struggle to link the remonte with my motor need assistance
Please contact our Technical Call Centre for advice on +27 11 699 2481
please help how to erase the nova remote from the d5 gatd motor
Please contact our Technical Call Centre for advice on +27 11 699 2481
how can i slow down my gate
HI centurion i want to be a distributor in Nigeria and as well install.
How do I download this video to my phone
GOD IS OHSOME
No hablo english y tengo problema con la instalacion de un motor D5 , parte y se para y el visor LCD me dice error en Fuente de Poder, Me puee ayudar alguien
Estimada Viviana. Podria enviarnos su direccion email e indicarnos el pais desde donde nos esta contactando?
tienes un problema en el cargador, posiblemente este dañado, debes reemplazarlo y listo. o tienes un cable flojo entre la fuente de poder y la tarjeta logica.
I have a electric sliding gate it works ok for about 20 times then it goes past stop sensor for no reason then I have to reset it again anybody got any ideas
Good people please always remember all these are man made so don't be intimidated
Hi
Por favor lo pueden decir en español
Español, Spanish .