I was super intimidated to replace our existing broken tile without having any previous experience/ knowledge, but this video was SUPER helpful and now I feel more confident on completing this project! Thanks!!
hi jeff. viewing your video several times provided comfortable confidence levels allowing me to proceed. my "diy" skill level can be called advanced althought i've not previously considered this kind of project. we needed four tiles replaced and after receiving three estimates ranging from $275 to $400 decided purchasing a quality cordless multi-tool and all other "hardware" we'd still be ahead of the professional estimated costs. to make a short story even "shorter": completely removed the broken four tiles and completed all preparations to clean the sites, making them "tile-ready" in just under two hours, including tool "set-up" and "take-down" time. mortar mixing, setting the replacement tiles' and applying grout accounted for another hour. we're very pleased with the finished product, saved money and acquired a new skill-set. a very productive day. can't "thank you" enough!! one comment, though: found drilling holes as suggested took a bit more time and in our case wasn't really necessary. prior to striking and breaking the three remaining tiles chiseling up and removing the remains, we made certain to first remove all existing grout surrounding each tile. wearing safety goggles we repeatedly struck the tiles until each cracked than used the "chisel-technique". worked very well for us. is possible to post links to all other of your "diy" videos?? thank you.
+2goblet2 thanks for your kind words, you can check out all of my videos right here on RUclips or over on Home Repair Tutor at www.homerepairtutor.com Congrats on doing a great job...any time you have a question feel free to reach out
Jeff, thank you for putting this video together. I am trying to replace three tiles in my bathroom but one of them needs to be cut so I am going to try to get it cut at the store. My suggestion to you to make your videos even better is to add a list of tools needed in your written description.
No, you do not need the store to do anything! But an angle grinder - preferably a Bosch 5" paddle switch, variable speed, Lock On button. Learn to use it. Add a Diamond tip blade to cut through any tile in seconds. Spray water as you cut. Put tile on table on top of wood or rubber mat. Clamp firmly. Spray with water. Wear protection eyes, nose, ears, gloves. Start cutting. So easy. Buy a refurbished one if you need to. Home Depot will match Amazon prices. Harbor Freight has discs cheap. This tool is more useful than a husband. Get one! Don't make excuses for being a woman.
Excellent Do It Yourself video! I'm pretty good at home repair, but it's nice to have information from someone who knows more than I . Many thanks! Jim Dickey, Sandy Springs, Georgia.
It could have been a 4 minute video but the way you explained everything was very helpful. Not just music in the background and people not actually learning anythng. I subscribed to your channel and shared it on my facebook page. I give you an A+....Mike
When installing/replacing porcelain tile on exterior locations ( outdoor decks, porches, etc), the mortar and gout are often times weather resistant compounds that contain a polymer that helps guard against weather and water damage. When using these polymer based products you do not wait any dry time to clean off any excess or haze. You will need to clean up asap as you apply the product because the polymer when dry becomes almost impossible to remove. So the 'typical' grout haze is not the same as a 'polymer' based grout haze. I typically when applying polymer grout limit as much as I can to placing the grout as near the tile seam as possible and keep as much as possible off the rest of the tile. It makes clean up and removal that much better. Think tar or candle wax spread over a tile and try and remove... :o)
Yea it boggles my mind that all these DIY guys smear grout over the entire tile. This absolutely makes ZERO sense to me. Why not just use your fingers to push it in along the edges!?
excellent video! i'm finally getting around to replacing a few tiles one at a time in places where duplicates of the cracked existing tiles are impossible to find. so far i have checked for level 2 days in a row and the tile is always lower the next day but i'm afraid to try to set it high. just hoping we don't trip over the resulting uneven floor.
Wow, you are a handsome man! The tutorial is excellent! I wondered how you approach the chiseling angle, and you start from the center - who would have thought? Makes sense. I would use a diamond hole saw not a drill bit though. This makes a good size hole and goes super fast. I drilled numerous porcelain, glass, and terracotta flower pots for extra holes and it zips through like a champ. The drill bit creates too much vibration, noise, and is 3 times slower to drill through. Here is a list of parts I would use: Diamond hole saw bit at 1/2" or any size. If you use a drill bit, it should be a masonry drill bit which also works to drill holes in concrete block walls (hang flower pots for example) Drill should be on hammer function not drill function. You will need a drill that has a hammer option. Hammer is for any concrete, ceramic, glass, porcelain, or stone drilling. Dremel Saw Max or Angle Grinder with a diamond blade or ordinary cutting blade (not metal but composite type) to cut through tile grout. Add water as you are cutting to cool down blade and lessen motor strain over dry dust cutting. Also, less dust. You can also use an angle grinder to smooth out lumpy dried thinset mortar instead of a chisel. Chisel for corners. Vacuum. Water spray bottle. Use Polymer in your thinset for better flexibility and hold. Use Polymer in your grout as a built in sealant so no need to reseal grout lines, this is done. This polymer rubberizes the grout and prevents cracking. I use polymer instead of water for all applications, especially tiling RV bathrooms or earthquake prone zones. MAPEI, an excellent Italian tile products maker, (only at Lowes, not Home Depot) makes a Grout Maximizer that is excellent. I love all MAPEI products - smart company and quality products. Works with any grout powder. Their polymer works with any Thinset Mortar powder too. Float - This should be very hard rubber, not a soft, bendable type. Hard will work. Soft, bendy type has no strength to push in the grout into the cracks. Every baker knows that hard rubber spatulas work and soft ones do not. Same principle here. Sponge type - That specific yellow one is what you want, not the cellulose type, but this lighter version. It works better. When you mix thinset mortar or grout, mix exactly as they state. Tiling and most trade skills are like baking a cake - not hard, but very precise technically. Do it wrong, or take shortcuts, it flops.
Thank you for the video and sharing your expertise! You touched on using a grout sealer... any recommendations with any that are extremely water proof? Thanks.
I'm about to replace a broken tile in the kitchen were my wife dropped an iron skillet and chipped the tile. The original install was done using Ditra uncoupled underlayment. I have extra sheets of Ditra that were leftovers. When I replace the tile should I also cut a piece of 18 x 18 underlayment and put it down then the tile ? my tiles are 18 x 18 and I have 3 extra boxes thank God. Thank you for your help in advance.
Video is fantastic ! Thank you , You saved me from calling a tile guy and a lot of money . If you have anymore building or construction videos please post them .
My pleasure to help any time Giovani22 - I try to post a new video every week on my RUclips channel and I also have a separate site called Home Repair Tutor, www.homerepairtutor.com.
A few steps before you contemplate this 1. Buy a bulldozer 2. Start up bulldozer 3. Level house with bulldozer 4. Collect insurance 5. Purchase a brand new house Well done you just saved heaps of time !!!
I just cracked my tile that I recently installed, thank you so much for posting this video!! I was freaking out about how to get the cracked piece out, I feel much better now!
Excellent video. Very clear and thorough instructions. My only concern is the time between mortaring tiles and grouting. You said 2-3 hours, others on google say 24 hours. I think I'll wait 24 to be sure.
hello I'm from Indonesia 🇮🇩, very lucky to meet you, even though we are from different countries. your video work is very beautiful, I always see it from every notification message that comes to the end of the video, I really appreciate your work, hopefully we can meet again in the latest video!.
Thank you for posting this! I needed insight and well as directions from A to Z. I've never replaced tile before, but now after seeing your video, I'm going for it!
Great video! It looks like the toothed trowel is awkward enough inside a 1x1 foot space, and my broken tile is 3x3 inches, so it won't even fit. Are there miniature trowels, or should I just use a small knife to apply the mortar and form ridges within the small space?
How do you replace an old grout? Thank you for this video, I’m doing my bathroom tile front door and under the kitchen sink where the disposal is cuz it leak and I need to change it. I removed the old linoleum and now the wood is expose and wet, I’m letting it dry. Is it ok to tile it when the wood dry and can I just cover the wall with cement to keep the mold from setting in? Thanks again
Just found the channel. Just got a little house that needs a lot of work to become a rental broken tiles something I’ve never done getting ready to start about eight broken tiles.
Thinset is the adhesive to attach tiles to floor or wall. You can get it premixed or powder to mix yourself with water. Grout is to put around tiles and it comes mostly in powder that you have to mix and comes in different colors.
This is a really good video. On a vertical I'm wondering if a multitool can be used instead of a hammer and chisel to remove the tile. I have 9mm plasterboard that I tanked and tiled about 6 years ago but I didn't seal properly and subsequently I have colour fade as the 'biscuit' has been affected by the ingress. I have three tiles affected and discolored and hoped that using only the multitool that I'd be able to remove the grout, cut slits into the affected tiles and remove the tiles and the old adhesive whilst hopefully maintaining the seal of the tanking so I can replace the three tiles and grout with a decent quality upstand strip...
have a new heater put in the bathroom he had to break a piece in the corner its a very narrow strip of tile to replace can i just fill it with a filler
any thinset mortar. a few to choose from, generally the same, the label will give specifics, tile aisle in home depot. small jobs you can get a premixed bucket, big jobs a 50lb bag.
we have a couple loose tiles in the bathroom floor. i was able to lift and remove the tiles exposing the mortar underneath. 3 or 4 tiles were perfect condition. so do i sand down the existing mortar to make room for new mortar or should i use a different type of adhesive compound?
Great info for diy project, Jeff - thanks for posting. I know you put out this video years ago, so I hope you are still replying to questions. My dilemma is that I need to repair or fill the mortar beneath a bathroom 1' × 1' tile that is NOT yet cracked but I fear soon wiil be if not fixed. The tile was installed before I bought the house & can't seem to find a duplicate match. So is it possible, If I use extreme care, to lift the existing tile without breaking it so that I may replace, using that same original tile once I clean out & re-level beneath it, then seal it back into place with fresh mortar & grout? Thanks a lot, your reply will be much appreciated.
Thanks Brian for your kindness. If the tile is loose, you can try to re-set it using thin-set mortar. That would be my first step. Make the grout joint relief cuts to increase the odds of the tile remaining in one piece 👍🏼
@@HomeRepairTutor thank you so much for the lightning quick reply to my question today, along with some of your own kind words and helpful advice. I would like your professional opinion about using the filler product, "Fix-A-Floor" please. It was brought to my attention & if used correctly, it SEEMS to be the perfect, simple & permanent solution to my tile issue. Do you recommend it or is it just some flaky, cheap & unproven flop of a product?
@@HomeRepairTutor I actually saw another RUclips video with the product. Thera are a few testimonial videos that show the customer using it in detail & this one is really short but to the point on how it works. I haven't used it yet but think I'm going to try it. Here's a link: ruclips.net/video/01CoOa0KtG4/видео.html
Do you have to remove ALL of the mortar under the old tile? It looks like you left some on? Or is that the substrate? Mins has some mesh screen type under the mortar.
Great video, thanks. Now I know I’m not going to do this- as buying all the different items would cost more than a handyman doing it for me. Weirdly, I have the same weird white tile.
My bathroom floor was covered with a ditra membrane before the tile installation. When replacing a tile, would I have to cut out a piece of the ditra membrane and replace with a new piece and then tile over it?
If the DITRA is in good shape you can leave it in place. You'll just have to remove all the old grout, I'd recommend a hammer and chisel or rasp blade on a multi-tool for that.
I have a cracked tile in my floor that needs to be replaced. Your video was very self-explanatory. I was wondering, how much for the tools to compete this job??
Thanks for easy to follow instructions, my wife has been nagging me for two years to replace the seven cracked tiles in the kitchen, I was just about to call in Sears and pay a ton of money.
If you have 7 cracked tiles you should first find out WHY that has happened! Simply replacing with new tiles on an uneven surface and it could happen again.
got a question---when i pulled up the single tile, the whole backer board came up with it---i went too deep with the grout saw...My guess is to try and remove the tile from that 12x12 piece of backer board, then try to thin set/screw that back down first, then start on the thin set on top to adhere the tile???
This is a great question THM and one I might answer in my podcast, too. I wonder if the backer board was never adhered to the subfloor with thin set. That's likely the case if you were able to easily pull it up. I'd recommend adding thin set to the subfloor before adhering the new piece of backer board my concern is that that would make the tile too high when your adhere it to the backer board. So, here's what I'd do (and by no means do you have to read this...): secure a new piece of backer board to the subfloor with alkali resistant screws (1 5/8 inch backer board screws). Then add the tile on top of the backer board with thin set. Another question though: is this tile next to the tub? If so, you should waterproof the backer board with something like RedGard. But make sure to wipe the RedGard off any adjacent tiles. This is a good place to start :D
really clear and simple descriptions and explanations step by step, I really will be able to have a go at it... thank you for the great tips! thank you! Manuel
How do you control new grout touching old grout for the touching tiles? Wouldnt the old grout crack and crumble when touching new grout due to the expansive pressure?
+Stephanie Hyder good question, thin-set mortar is used to bond tiles to subfloor or vertical surfaces. Grout goes between tiles. Grout is not a form of waterproofing, figured I'd mention that since it's a common myth :)
If you have a tile that has old grout on it how is the best way to get the old grout off the old tile to be able to re-use the same tile. The tiles around the sink are variable sizes so I want to re-use the original tile which is not damaged.
I picked up a grout removal tool and scraper set for my sawsall. The grout removal toollwas slow then I just cut right though the damaged with my angle grinder with a blade that cuts through things like tile or even concrete. I carefully cut the edge for the tile and grourI smashed the tile with a hammer and scraped everything up with my sawall and scaper tool. I was definitely risking damaging the surrounding tiles by using the sawsall and scraper tools but I have lots of extra tiles. I guess I have good tool control because I didn't damage any surrounding tiles.
Good Video. You can also use the side of your rubber gloved hand instead of the rubber float to push the grout in. Use the float as clean up. This is a good technique especially for DIYers even in doing whole floors. I find it to be a lot faster and at least as effective for me who may do a floor every 5 years or so.
Hi home repair tutor we wants change our tiles but one worker said new tile never adjust in old floor because of dry timing old floor is already dry new material or tile bond never like first time of flooring.is this make sense or only a myth? Can you explain me plz?
Thanks for the information! I have one question. Can I reuse a tile? My tile floor began to lift up, but the tiles are not damaged. I pulled up four of them before I saw the repair videos that said not to do that. So, can I reuse these tiles or will the thin set stuck to the back of the tiles cause more trouble later on?
Bonnie Hanchey if you can get the thin-set off the back of the tile then you can use it. Just make sure the back of the tile is super clean. Otherwise it won't adhere properly to the thin-set. I'd also recommend back buttering the tile, putting a thin layer on it, then setting in the thin-set on the substrate.
One thing I learned was stay away from cement board under the tile. In my house, we use two plywoods. The tile is on a 5/8" plywood on top of the original plywood. Its not as resilient as tile over cement board but comes up much easier if you need to replace a tile.
Hey Jeff, thanks for the video! I have an odd follow up question for you. Where did you find your replacement tile?? The broken tile I have looks exactly like yours (white with a glazed texture) and I've been looking all over for some replacement tiles. Thanks!!
Hi, thanks for this video i have some steps with about 60 small tiles to replace and everyone has told me the whole lot need to come off as opposed to removing a neat square out in the middle leaving the main borders in place. my challenge is to remove the sand and cement mortar mix "screed" we call it in the UK as its very tough but i have mini grinder and a multi tool so should be ok. i am a handy man in the UK and one tile or 3 would be a blessing but 60 1"x1" and half of them need to be cut into triangular shapes is going to be tricky but hey he who dares wins!! instead of swearing im going to treat each tile as a single repair think of your video and then whack myself over the head so i get amnesia and cant remember fixing each one so in theory ill only replace one not 60!! ok i wish but thats the kind of attitude towards it im taking. i will let you know how i get on and may need some much appreciated advise if poss. cheers Paul. Brighton England UK.
It was a good video, except that you fast forwarded through every process!! Also, where did you get that tile? I need the exact same pieces, may be 6 of them.. Please let me know.
I want to replace a damaged tile, it is very helpful to watch your demonstration. A great Thank you from a citizen in Hong Kong. 🙏
7 years old and still one of the best tutorials I've watched, thank you for this.
Eight years later and this video is still perfect. Replacing five tiles in the kitchen ... piece of cake now.
Much simpler than the Home Depot version. 10 years later and still the best out there.
I was super intimidated to replace our existing broken tile without having any previous experience/ knowledge, but this video was SUPER helpful and now I feel more confident on completing this project! Thanks!!
+Lauren Ramsey awesome, did your project end in success? Sounds like it 😀
No experience and this really helped me - especially what tools I needed
hi jeff. viewing your video several times provided comfortable confidence levels allowing me to proceed. my "diy" skill level can be called advanced althought i've not previously considered this kind of project. we needed four tiles replaced and after receiving three estimates ranging from $275 to $400 decided purchasing a quality cordless multi-tool and all other "hardware" we'd still be ahead of the professional estimated costs. to make a short story even "shorter": completely removed the broken four tiles and completed all preparations to clean the sites, making them "tile-ready" in just under two hours, including tool "set-up" and "take-down" time. mortar mixing, setting the replacement tiles' and applying grout accounted for another hour. we're very pleased with the finished product, saved money and acquired a new skill-set. a very productive day. can't "thank you" enough!! one comment, though: found drilling holes as suggested took a bit more time and in our case wasn't really necessary. prior to striking and breaking the three remaining tiles chiseling up and removing the remains, we made certain to first remove all existing grout surrounding each tile. wearing safety goggles we repeatedly struck the tiles until each cracked than used the "chisel-technique". worked very well for us. is possible to post links to all other of your "diy" videos?? thank you.
+2goblet2 thanks for your kind words, you can check out all of my videos right here on RUclips or over on Home Repair Tutor at www.homerepairtutor.com
Congrats on doing a great job...any time you have a question feel free to reach out
appreciate your prompt comments. thanks, again.
Jeff, thank you for putting this video together. I am trying to replace three tiles in my bathroom but one of them needs to be cut so I am going to try to get it cut at the store.
My suggestion to you to make your videos even better is to add a list of tools needed in your written description.
Thank you for suggesting that he add a list of tools needed in his written description, because it looks like he listened. 😀
No, you do not need the store to do anything! But an angle grinder - preferably a Bosch 5" paddle switch, variable speed, Lock On button. Learn to use it. Add a Diamond tip blade to cut through any tile in seconds. Spray water as you cut. Put tile on table on top of wood or rubber mat. Clamp firmly. Spray with water. Wear protection eyes, nose, ears, gloves. Start cutting. So easy.
Buy a refurbished one if you need to. Home Depot will match Amazon prices. Harbor Freight has discs cheap.
This tool is more useful than a husband. Get one! Don't make excuses for being a woman.
Thank you for the very comprehensive and down to earth video. This video boosted up my confidence in tackling my home repair. God bless brother 🙏.
Excellent Do It Yourself video! I'm pretty good at home repair, but it's nice to have information from someone who knows more than I . Many thanks! Jim Dickey, Sandy Springs, Georgia.
you likely know more, ever thought about making videos?
It could have been a 4 minute video but the way you explained everything was very helpful. Not just music in the background and people not actually learning anythng. I subscribed to your channel and shared it on my facebook page. I give you an A+....Mike
thanks, that's the best grade one can get!!
When installing/replacing porcelain tile on exterior locations ( outdoor decks, porches, etc), the mortar and gout are often times weather resistant compounds that contain a polymer that helps guard against weather and water damage. When using these polymer based products you do not wait any dry time to clean off any excess or haze. You will need to clean up asap as you apply the product because the polymer when dry becomes almost impossible to remove. So the 'typical' grout haze is not the same as a 'polymer' based grout haze. I typically when applying polymer grout limit as much as I can to placing the grout as near the tile seam as possible and keep as much as possible off the rest of the tile. It makes clean up and removal that much better. Think tar or candle wax spread over a tile and try and remove... :o)
Yea it boggles my mind that all these DIY guys smear grout over the entire tile. This absolutely makes ZERO sense to me. Why not just use your fingers to push it in along the edges!?
excellent video! i'm finally getting around to replacing a few tiles one at a time in places where duplicates of the cracked existing tiles are impossible to find. so far i have checked for level 2 days in a row and the tile is always lower the next day but i'm afraid to try to set it high. just hoping we don't trip over the resulting uneven floor.
Wow, you are a handsome man! The tutorial is excellent! I wondered how you approach the chiseling angle, and you start from the center - who would have thought? Makes sense.
I would use a diamond hole saw not a drill bit though. This makes a good size hole and goes super fast. I drilled numerous porcelain, glass, and terracotta flower pots for extra holes and it zips through like a champ. The drill bit creates too much vibration, noise, and is 3 times slower to drill through. Here is a list of parts I would use:
Diamond hole saw bit at 1/2" or any size.
If you use a drill bit, it should be a masonry drill bit which also works to drill holes in concrete block walls (hang flower pots for example)
Drill should be on hammer function not drill function. You will need a drill that has a hammer option. Hammer is for any concrete, ceramic, glass, porcelain, or stone drilling.
Dremel Saw Max or Angle Grinder with a diamond blade or ordinary cutting blade (not metal but composite type) to cut through tile grout. Add water as you are cutting to cool down blade and lessen motor strain over dry dust cutting. Also, less dust.
You can also use an angle grinder to smooth out lumpy dried thinset mortar instead of a chisel.
Chisel for corners.
Vacuum.
Water spray bottle.
Use Polymer in your thinset for better flexibility and hold.
Use Polymer in your grout as a built in sealant so no need to reseal grout lines, this is done. This polymer rubberizes the grout and prevents cracking. I use polymer instead of water for all applications, especially tiling RV bathrooms or earthquake prone zones. MAPEI, an excellent Italian tile products maker, (only at Lowes, not Home Depot) makes a Grout Maximizer that is excellent. I love all MAPEI products - smart company and quality products. Works with any grout powder. Their polymer works with any Thinset Mortar powder too.
Float - This should be very hard rubber, not a soft, bendable type. Hard will work. Soft, bendy type has no strength to push in the grout into the cracks. Every baker knows that hard rubber spatulas work and soft ones do not. Same principle here.
Sponge type - That specific yellow one is what you want, not the cellulose type, but this lighter version. It works better.
When you mix thinset mortar or grout, mix exactly as they state. Tiling and most trade skills are like baking a cake - not hard, but very precise technically. Do it wrong, or take shortcuts, it flops.
Thank you for the video and sharing your expertise! You touched on using a grout sealer... any recommendations with any that are extremely water proof? Thanks.
Have you tried an SDS plus with tile chisel? Makes quick work.
Stack & Tier that’s what I was thinking too. I mean with care obviously I don’t see why not
Going to fix my kitchen tiles soon after watching the video...Thanku so much👍
How do you put the 13:01 "dip" in the grout? Thanks, very helpful.
I'm about to replace a broken tile in the kitchen were my wife dropped an iron skillet and chipped the tile. The original install was done using Ditra uncoupled underlayment. I have extra sheets of Ditra that were leftovers. When I replace the tile should I also cut a piece of 18 x 18 underlayment and put it down then the tile ? my tiles are 18 x 18 and I have 3 extra boxes thank God. Thank you for your help in advance.
Wonderful video!! What kind of cement is recommended?
Video is fantastic ! Thank you , You saved me from calling a tile guy and a lot of money . If you have anymore building or construction videos please post them .
My pleasure to help any time Giovani22 - I try to post a new video every week on my RUclips channel and I also have a separate site called Home Repair Tutor, www.homerepairtutor.com.
Great video. I watched your video's on tile installation prior to tiling my bathroom. Ended up at this video after 1 of the tiles cracked.
Thanks Robert, awesome to hear you tiled your bathroom. It'll last a long time.
A few steps before you contemplate this
1. Buy a bulldozer
2. Start up bulldozer
3. Level house with bulldozer
4. Collect insurance
5. Purchase a brand new house
Well done you just saved heaps of time !!!
Excellent video. Well explained and very clear. Bravo and greetings from the UK!
I just cracked my tile that I recently installed, thank you so much for posting this video!! I was freaking out about how to get the cracked piece out, I feel much better now!
That’s horrible! My wife would freak out !
Excellent video. Very clear and thorough instructions. My only concern is the time between mortaring tiles and grouting. You said 2-3 hours, others on google say 24 hours. I think I'll wait 24 to be sure.
Thanks for the video. I wonder why you did not use the grit remover machine to cut the tile into pieces. It is must safer, quicker and more efficient
hello I'm from Indonesia 🇮🇩, very lucky to meet you, even though we are from different countries. your video work is very beautiful, I always see it from every notification message that comes to the end of the video, I really appreciate your work, hopefully we can meet again in the latest video!.
Thank you for posting this! I needed insight and well as directions from A to Z. I've never replaced tile before, but now after seeing your video, I'm going for it!
How'd it work out?
Great video! It looks like the toothed trowel is awkward enough inside a 1x1 foot space, and my broken tile is 3x3 inches, so it won't even fit. Are there miniature trowels, or should I just use a small knife to apply the mortar and form ridges within the small space?
Thanks for the video...it was a huge help in replacing 2 cracked tiles in my kitchen. Saved me a lot of time and aggravation...keep posting!
+Dave Keiper thanks. Glad to hear it helped. Great job because this isn't the easiest project
+Dave Keiper thanks. Glad to hear it helped. Great job because this isn't the easiest project
This one of those very satisfying videos to watch! Great video!
How do you replace an old grout? Thank you for this video, I’m doing my bathroom tile front door and under the kitchen sink where the disposal is cuz it leak and I need to change it. I removed the old linoleum and now the wood is expose and wet, I’m letting it dry. Is it ok to tile it when the wood dry and can I just cover the wall with cement to keep the mold from setting in? Thanks again
Just found the channel. Just got a little house that needs a lot of work to become a rental broken tiles something I’ve never done getting ready to start about eight broken tiles.
Is the grout call thinset? Or is it 2 different things. Also does it come premixed ? I have 2 cracked patio tiles. Think I might give it a go
Thinset is the adhesive to attach tiles to floor or wall.
You can get it premixed or powder to mix yourself with water.
Grout is to put around tiles and it comes mostly in powder that you have to mix and comes in different colors.
This is a really good video. On a vertical I'm wondering if a multitool can be used instead of a hammer and chisel to remove the tile. I have 9mm plasterboard that I tanked and tiled about 6 years ago but I didn't seal properly and subsequently I have colour fade as the 'biscuit' has been affected by the ingress. I have three tiles affected and discolored and hoped that using only the multitool that I'd be able to remove the grout, cut slits into the affected tiles and remove the tiles and the old adhesive whilst hopefully maintaining the seal of the tanking so I can replace the three tiles and grout with a decent quality upstand strip...
Many thanks, very clear and pleasant to watch
have a new heater put in the bathroom he had to break a piece in the corner its a very narrow strip of tile to replace can i just fill it with a filler
Hey Jeff, great video. How do I know what kind of mortar to use on a concrete floor? Is it all the same?
any thinset mortar. a few to choose from, generally the same, the label will give specifics, tile aisle in home depot. small jobs you can get a premixed bucket, big jobs a 50lb bag.
I’m buying a house for the first time in my life and it needs some fixing, tiles especially thank you so much!
Great video! EVERYTHING I needed to know about changing a tile. Excellent detail! Thank you!
we have a couple loose tiles in the bathroom floor. i was able to lift and remove the tiles exposing the mortar underneath. 3 or 4 tiles were perfect condition. so do i sand down the existing mortar to make room for new mortar or should i use a different type of adhesive compound?
Do you only have to avoid walking on the replaced tile or the tiles surrounding it as well, or the entire tile floor? And for how long?
Thank you so much for your time & the video what a huge help! (For my husband :) ) what do you recommend for a grout sealer?
Great! Choose a sealer made by the company who makes the grout. That way you know it’ll be compatible.
Thank you What is the difference between. thinset and. grout
Great info for diy project, Jeff - thanks for posting. I know you put out this video years ago, so I hope you are still replying to questions. My dilemma is that I need to repair or fill the mortar beneath a bathroom 1' × 1' tile that is NOT yet cracked but I fear soon wiil be if not fixed. The tile was installed before I bought the house & can't seem to find a duplicate match. So is it possible, If I use extreme care, to lift the existing tile without breaking it so that I may replace, using that same original tile once I clean out & re-level beneath it, then seal it back into place with fresh mortar & grout? Thanks a lot, your reply will be much appreciated.
Thanks Brian for your kindness. If the tile is loose, you can try to re-set it using thin-set mortar. That would be my first step. Make the grout joint relief cuts to increase the odds of the tile remaining in one piece 👍🏼
@@HomeRepairTutor thank you so much for the lightning quick reply to my question today, along with some of your own kind words and helpful advice. I would like your professional opinion about using the filler product, "Fix-A-Floor" please. It was brought to my attention & if used correctly, it SEEMS to be the perfect, simple & permanent solution to my tile issue. Do you recommend it or is it just some flaky, cheap & unproven flop of a product?
I’m not familiar with it, what’s the purpose or how is it being recommended?
@@HomeRepairTutor I actually saw another RUclips video with the product. Thera are a few testimonial videos that show the customer using it in detail & this one is really short but to the point on how it works.
I haven't used it yet but think I'm going to try it. Here's a link:
ruclips.net/video/01CoOa0KtG4/видео.html
Very well explained, well illustrated and complete solution. Thank you.
David Levins glad to help any time with your cracked tile issues, thanks for watching :D
Do you have to remove ALL of the mortar under the old tile? It looks like you left some on? Or is that the substrate? Mins has some mesh screen type under the mortar.
Great instructional video! Thanks!
Great video, thanks.
Now I know I’m not going to do this- as buying all the different items would cost more than a handyman doing it for me. Weirdly, I have the same weird white tile.
My bathroom floor was covered with a ditra membrane before the tile installation. When replacing a tile, would I have to cut out a piece of the ditra membrane and replace with a new piece and then tile over it?
If the DITRA is in good shape you can leave it in place. You'll just have to remove all the old grout, I'd recommend a hammer and chisel or rasp blade on a multi-tool for that.
Great video. Two tiles needs to be replaced in our hallway and it'll be done soon now 👍👍
I have a cracked tile in my floor that needs to be replaced. Your video was very self-explanatory. I was wondering, how much for the tools to compete this job??
Excellent Tutorial ❤
Thanks for easy to follow instructions, my wife has been nagging me for two years to replace the seven cracked tiles in the kitchen, I was just about to call in Sears and pay a ton of money.
+Papito1949 you can do it, just takes patience and elbow grease
If you have 7 cracked tiles you should first find out WHY that has happened! Simply replacing with new tiles on an uneven surface and it could happen again.
Thanks, man...your video saved me a TON of money with my restaurant kitchen flooring...
Bobby, OH
+robertburdette awesome!! Great job fixing it yourself
great job, I'd like to have seen the grout sealing, I don't think mine ever was..
Mine as well
Great demonstration! Thank you!
got a question---when i pulled up the single tile, the whole backer board came up with it---i went too deep with the grout saw...My guess is to try and remove the tile from that 12x12 piece of backer board, then try to thin set/screw that back down first, then start on the thin set on top to adhere the tile???
This is a great question THM and one I might answer in my podcast, too. I wonder if the backer board was never adhered to the subfloor with thin set. That's likely the case if you were able to easily pull it up. I'd recommend adding thin set to the subfloor before adhering the new piece of backer board my concern is that that would make the tile too high when your adhere it to the backer board.
So, here's what I'd do (and by no means do you have to read this...): secure a new piece of backer board to the subfloor with alkali resistant screws (1 5/8 inch backer board screws). Then add the tile on top of the backer board with thin set.
Another question though: is this tile next to the tub? If so, you should waterproof the backer board with something like RedGard. But make sure to wipe the RedGard off any adjacent tiles.
This is a good place to start :D
Jeff Patterson I did what you said--it worked great! Thanks so much for the info. Can't tell what tile was replaced! thanks again.
really clear and simple descriptions and explanations step by step, I really will be able to have a go at it... thank you for the great tips! thank you! Manuel
Can you please show how to apply grout sealer?
How do you control new grout touching old grout for the touching tiles? Wouldnt the old grout crack and crumble when touching new grout due to the expansive pressure?
what is the difference between mortar and grout?
+Stephanie Hyder good question, thin-set mortar is used to bond tiles to subfloor or vertical surfaces. Grout goes between tiles. Grout is not a form of waterproofing, figured I'd mention that since it's a common myth :)
good video. I didn't use gloves, had to spend a few extra minutes cleaning up the blood drops, cracked tile very similar to broken glass.
Is there any risk that the thinset will shrink when it cures so the tile will sink?
Thanks man right to point and not that bad :)
If you have a tile that has old grout on it how is the best way to get the old grout off the old tile to be able to re-use the same tile. The tiles around the sink are variable sizes so I want to re-use the original tile which is not damaged.
Great video, I learn a lot, pretty easy to understand, thank you!
So easily explained!!
BTW awsome video eventhough im always in a rush i was patient enough to stick around till the end of the video because it was so well explained.
Thank You from Puerto Rico.
Thanks for starting with safety tips.
How do you mix the mortar?
I picked up a grout removal tool and scraper set for my sawsall. The grout removal toollwas slow then I just cut right though the damaged with my angle grinder with a blade that cuts through things like tile or even concrete. I carefully cut the edge for the tile and grourI smashed the tile with a hammer and scraped everything up with my sawall and scaper tool. I was definitely risking damaging the surrounding tiles by using the sawsall and scraper tools but I have lots of extra tiles. I guess I have good tool control because I didn't damage any surrounding tiles.
Roughly how long should that one tile replacement take for the whole project?
damn this is a lot of freakin work
No kidding!
Good Video. You can also use the side of your rubber gloved hand instead of the rubber float to push the grout in. Use the float as clean up. This is a good technique especially for DIYers even in doing whole floors. I find it to be a lot faster and at least as effective for me who may do a floor every 5 years or so.
Thanks for the great tips. I sometimes just use a gloved hand for small areas that are unreachable with the float.
This was very helpful ❤
Hi home repair tutor we wants change our tiles but one worker said new tile never adjust in old floor because of dry timing old floor is already dry new material or tile bond never like first time of flooring.is this make sense or only a myth? Can you explain me plz?
Thanks for the information! I have one question. Can I reuse a tile? My tile floor began to lift up, but the tiles are not damaged. I pulled up four of them before I saw the repair videos that said not to do that. So, can I reuse these tiles or will the thin set stuck to the back of the tiles cause more trouble later on?
Bonnie Hanchey if you can get the thin-set off the back of the tile then you can use it. Just make sure the back of the tile is super clean. Otherwise it won't adhere properly to the thin-set. I'd also recommend back buttering the tile, putting a thin layer on it, then setting in the thin-set on the substrate.
Very helpful, thank you
thank you!
Wow great video 10 years on
Gonna try this out. Thanks
Hi, without any experience can I do it?
Thanks, i dont have all those tools but just had to know how to remove the broken one.
+stephen mcewan did you remove a broken tub?
+Jeff Patterson tub ? tile yes ty
Helpful - thanks so much for posting this video
Great video mate. Would you apply the same technique to fix a new soap dish to a shower wall?
Peter Zammit thanks! Is your soap dish attached to a tile or to the wall cement board?
Ive taken the plunge and went for it. Its currently held in place with tape until tomorrow. Did it some 8 hours ago. Seems pretty dolid so far.
great job, let me know how it holds up.
Well, yesterday I hit my head on the bottom of the soap dish REALLY hard. Didn't fall off. Doesn't even wiggle.
That's a good test, for both the dish and your head, lol. Hope you're okay.
Just love this guy
🙏🏼🔥
How much would it cost to have two tiles replaced? Both material and manual labor. Please thank you. Cheers from New York City
One thing I learned was stay away from cement board under the tile. In my house, we use two plywoods. The tile is on a 5/8" plywood on top of the original plywood. Its not as resilient as tile over cement board but comes up much easier if you need to replace a tile.
Hey Jeff, thanks for the video! I have an odd follow up question for you. Where did you find your replacement tile?? The broken tile I have looks exactly like yours (white with a glazed texture) and I've been looking all over for some replacement tiles.
Thanks!!
It was in my garage, lol. Fortunately the prior homeowners kept some. Where do you live? I could send one to you.
Well I looking 3...but I live in Greenville SC
You can find anything online. Just look at tile makers products online. Even Home Depot has extensive online selections they cannot display in stores.
Great video Jeff it's really helpful for DIY'ers
Thank you for your video and the time you took to make it.
James Jackson thank you for your kind words, I hope it helped :D
To get the thinset out use your oscillating tool with a carbide flat blade.
Hi, thanks for this video i have some steps with about 60 small tiles to replace and everyone has told me the whole lot need to come off as opposed to removing a neat square out in the middle leaving the main borders in place. my challenge is to remove the sand and cement mortar mix "screed" we call it in the UK as its very tough but i have mini grinder and a multi tool so should be ok. i am a handy man in the UK and one tile or 3 would be a blessing but 60 1"x1" and half of them need to be cut into triangular shapes is going to be tricky but hey he who dares wins!! instead of swearing im going to treat each tile as a single repair think of your video and then whack myself over the head so i get amnesia and cant remember fixing each one so in theory ill only replace one not 60!! ok i wish but thats the kind of attitude towards it im taking.
i will let you know how i get on and may need some much appreciated advise if poss.
cheers Paul. Brighton England UK.
After reading your nonsense I'll make sure I never look for a handyman called Paul from Brighton .. looks like a disaster!
getting it done! thanks
good video - I would probably have showed adding the grout sealant
+David Caughell But yeah, this video was exactly what I was looking for, thank you!
+David Caughell cool, glad it helled
It was a good video, except that you fast forwarded through every process!! Also, where did you get that tile? I need the exact same pieces, may be 6 of them.. Please let me know.
Awesome! Thx a lot for taking time to make this video.
I haven't seen a video yet talking about replacing a tile that's attached to Ditra?
+Gazooo29 DITRA is a great crack isolation membrane, we have tutorial using it 👍
Thanks great info 👍