This really helped me fix my double roller door as it wasn't aligned properly and we had to hold it tight together to get it to lock. It's so much easier now after adjusting the rollers to get it to align. Locks easy and smoother as well. All thanks to this video tutorial.
Thanks! I could hardly open the door at all! After doing what the video said, I also took the door off completely (lift up over track) and was able to clean the track you can't get to on a daily basis, and it had at least a 1/4 " of dirt and hair in there which was also making the door stick and squeek. After I got all the dirt off the entire track, it works like a charm!
Need to advise people to lift the frame of door up to prevent stripping of the screw when making the adjustment because the weight of the door is on the screw when it is turn. Thx My door frame is steel, with the glass, it is little bit heavy. Lifting the frame up while turning the screw is recommended. Thx
My problem is the track cracked. Like the video, it is just thin plastic w/ a stainless steel cap. The moveable Anlin door is 47" wide and double-pane, so apparently too heavy for the track. We have rarely used that door, and much less since it got very hard to close from the broken track. Another Anlin door 37" wide was installed the same time ~2002 and its track is still OK. A lot of manufacturers used these same plastic tracks, but Anlin should have evaluated them more. I am looking for a smarter design to replace, but even getting the original track is proving tedious.
Hi William, Anlin has evaluated this issue and has designed a new track and roller system that allows for a lifetime of durability and easy operation. Anlin now uses a stainless steel "pyramid" track that is stronger and can withstand the weight of our larger doors. You can contact our service department at 1-800-899-4896 and they will be able to assist you and replace your old track with the new track.
In south Africa the screws are retracted inside a hole. Trying to find the screw head that's out of sight while also being hampered by a screw driver with a large wide handle. The handle causes the screw driver to enter the hole at an angle so you miss the target. This is because the door frame has a ledge which is higher than the hole. I've simply given up and resigned myself to having a door thats not flush. A real pain.
What does one do if you run out of adjustment and sliding glass door is still not square? Had brand new door wall installed and needless to say they did a less than stellar job. Top of slider leans forward and roller is fully adjusted up and rear fully lowered. Now what?
This really helped me fix my double roller door as it wasn't aligned properly and we had to hold it tight together to get it to lock. It's so much easier now after adjusting the rollers to get it to align. Locks easy and smoother as well. All thanks to this video tutorial.
Mm?
Excellent video. Thank you and thank you for what you do.
Thanks! I could hardly open the door at all! After doing what the video said, I also took the door off completely (lift up over track) and was able to clean the track you can't get to on a daily basis, and it had at least a 1/4 " of dirt and hair in there which was also making the door stick and squeek. After I got all the dirt off the entire track, it works like a charm!
Thank you! Now I have my patio door fixed.
This is not the brand of my door but the instructions were great and I fixed my door so it glides like a knife through soft butter.
Thanks!!!
Now I can adjusted my sliding glass door
Well that Fixed my misaligned door! Thanks
Need to advise people to lift the frame of door up to prevent stripping of the screw when making the adjustment because the weight of the door is on the screw when it is turn. Thx
My door frame is steel, with the glass, it is little bit heavy. Lifting the frame up while turning the screw is recommended. Thx
X L thanks for this information
My problem is the track cracked. Like the video, it is just thin plastic w/ a stainless steel cap. The moveable Anlin door is 47" wide and double-pane, so apparently too heavy for the track. We have rarely used that door, and much less since it got very hard to close from the broken track. Another Anlin door 37" wide was installed the same time ~2002 and its track is still OK. A lot of manufacturers used these same plastic tracks, but Anlin should have evaluated them more. I am looking for a smarter design to replace, but even getting the original track is proving tedious.
Hi William,
Anlin has evaluated this issue and has designed a new track and roller system that allows for a lifetime of durability and easy operation. Anlin now uses a stainless steel "pyramid" track that is stronger and can withstand the weight of our larger doors. You can contact our service department at 1-800-899-4896 and they will be able to assist you and replace your old track with the new track.
@@AnlinWindowsDoors I'm glad to read this as I'm soon to become one of your customers via Clarke and Rush here in Sacramento.
Fixed my door! Thanks.
In south Africa the screws are retracted inside a hole.
Trying to find the screw head that's out of sight while also being hampered by a screw driver with a large wide handle. The handle causes the screw driver to enter the hole at an angle so you miss the target. This is because the door frame has a ledge which is higher than the hole.
I've simply given up and resigned myself to having a door thats not flush. A real pain.
Thanks for this video , u save my money
Wow, thanks. I hope it works
i dont have a upper screw in mine, i have a hole on both ends and only a screw at the bottom. how do i adjust that?
What does one do if you run out of adjustment and sliding glass door is still not square? Had brand new door wall installed and needless to say they did a less than stellar job. Top of slider leans forward and roller is fully adjusted up and rear fully lowered. Now what?
Hello. Please visit anlin.com/contact-us/ or contact our Consumer Services department at (800) 287-7996.
Is it just a simple screw that I can remove and replace? I have one that is completely stripped
What if there is no screws just a hole :s
There was a screw on top of it to order 2 of eBay replaced all fixed 😀
My screws are stripped as hell. Thanks, previous tenant.
You can replace the rollers pretty cheaply
How
My door can't even roll front it's stuck in place