Great Advice! Also; during the final cleaning, I spray into a torn-off section of an old towel so the acetone doesn't fly back into my face. Then; you can use the towel to clean the gun because it's already soaked with acetone. Thanks for the video! Scotty
Great video. You obviously have a system that works, I'm a great fan of the 3M PPS products just the cups and liners will save you all the cup cleaning time and now that there are plenty of knock offs available for the adapters liners and outers the cost is pretty cheap too, just remember to pull the built in filter out if you're spraying Gelcoat. The Accuspray guns, especially the HO versions with pressure feed are great. Tips for the Accuspray aren't that expensive, can usually be reused and if it all goes wrong and the Gelcoat sets up well you've only lost a $5 tip
Thanks Ross! I always learn new things from you. I disliked the cleanup part of the job, but it is important and you just made it easier. Oh and now I have to throw out the gel coat I've been keeping around for a couple of years! 😁
@@Scifi_Ape Our waste management company has a hazmat day every so often. You can take it to them and they will properly dispose of it for you, ands it's free where I live. Otherwise I would guess it is like paint, add the hardener and you can dispose of it like any other solid. I live in the US it might be totally different in other places.
Hi Ross, You ask for thing we would like to see and here is mine. Can you show how to do overhead glassing? I am talking like tabbing or repairs where the glass wants to fall away while you work. I am sure you will be doing a lot of this on your boat build and I am eager to see it done. Thanks so much for these videos I wish they were here 20 years ago when I was working in glass.
Great video man lots of valuable information I have a few question for you. Did you used Gel Coat with Paraffin?and how many coats? When should the one without Paraffin be used and how many coats before giving the one with Paraffin? Where do you buy spray gel coat?
Thanks Mr. Good night, i have one doubt: this is possible apply gel coat with gun in external Surface ( ex. Sail boat) ? Thanks best regards. Renato from Brazil.
Hi ! How are you today, My Name is Mr.Herman Woods. I have to RC BOATS ! I WAS WATCHING YOUR VIDEO. AND I SAW YOUR GELCOT GUN SPRAYER . I SAW A GUN LIKE THAT ! , BUT I THINK IT IS A DIFFERENT MODEL . BUT IT COME WITH 3 NOZZLE"S .AND THAT LAST NOZZLE ! IS A 2.5MM .THEY SAY ! IT WILL PAINT AUTOMOTIVE .BUT IT DID NOT SAY ANYTHING ABOUT GELCOT . SO ! I WONTED TO ASK YOU ! IF MY NOZZLE IS A 2.5 .WILL I BE ALL RIGHT ! WITH THE GUN .ITS A HVLP GUN . OUR ! I NEED TO GET WHAT YOU HAVE.!! CAN YOU LET ME KNOW.THANK YOU FOR YOUR TIME .MR.H.WOODS ! THANK YOU .
Say you were shooting a big mould, not quite as big as yours. And didn’t have a proper resin gun, do you reckon it’s possible to do with 3 of these guns and have a mixer person, a cleaner and a sprayer. Do you like these guns better than the other gelcoat guns that have the paper inserts and the cup on the back of the gun that are sold as “gelcoat guns”
I honestly think a G100 cup gun is a much better solution for larger moulds.Hvlp guns are excellent small job tools and gear for repairs etc You would need to be constantly changing cups with a cup gun and I have sprayed moulds with 4-5 cups full at a sitting.The key is keeping pressure constant and moisture out of the air feed A dryer or gravity drain with moisture trap/ filter is an essential in any case.Rossco.
Great Advice! Also; during the final cleaning, I spray into a torn-off section of an old towel so the acetone doesn't fly back into my face. Then; you can use the towel to clean the gun because it's already soaked with acetone. Thanks for the video! Scotty
Great tip on cleaning the HVLP. Thanks for sharing.
Thanks Andrew
This video was insanely helpful, thank you!
Very cool. Thanks for the tips Ross!
Great video. You obviously have a system that works, I'm a great fan of the 3M PPS products just the cups and liners will save you all the cup cleaning time and now that there are plenty of knock offs available for the adapters liners and outers the cost is pretty cheap too, just remember to pull the built in filter out if you're spraying Gelcoat. The Accuspray guns, especially the HO versions with pressure feed are great. Tips for the Accuspray aren't that expensive, can usually be reused and if it all goes wrong and the Gelcoat sets up well you've only lost a $5 tip
Great work and well explained…
Thanks Colin
Thanks Ross! I always learn new things from you. I disliked the cleanup part of the job, but it is important and you just made it easier. Oh and now I have to throw out the gel coat I've been keeping around for a couple of years! 😁
I know it is hard to throw it out but it will only cause heartache when you have to do the job twice Daniel.Cheers buddy.Ross
@@Scifi_Ape Our waste management company has a hazmat day every so often. You can take it to them and they will properly dispose of it for you, ands it's free where I live. Otherwise I would guess it is like paint, add the hardener and you can dispose of it like any other solid. I live in the US it might be totally different in other places.
Get the 3M pps system.Throw away the liner and clean out the gun in a fraction of the time with 1/10 of the solvent.
Hi Ross,
You ask for thing we would like to see and here is mine. Can you show how to do overhead glassing? I am talking like tabbing or repairs where the glass wants to fall away while you work. I am sure you will be doing a lot of this on your boat build and I am eager to see it done. Thanks so much for these videos I wish they were here 20 years ago when I was working in glass.
very informative, thank you sir!
Thanks for watching buddy.
Thanks 4 the advise !!!
Thanks buddy
Great info
Mofiac is the name of the guy that does the gun cleaning video
Great video, thankyou!
My pleasure mate.Thanks
Great vid, thanks! What are the part numbers of the 3m filters that you are using on the protection mask?
Great video man lots of valuable information
I have a few question for you. Did you used Gel Coat with Paraffin?and how many coats?
When should the one without Paraffin be used and how many coats before giving the one with Paraffin?
Where do you buy spray gel coat?
Why don't you guys specify the CFM requirements?
Thanks Mr. Good night, i have one doubt: this is possible apply gel coat with gun in external Surface ( ex. Sail boat) ? Thanks best regards.
Renato from Brazil.
Simply mix about 10percent wax in styrene to mske flow coat and you can spray onto external surface then sand and polish to a finish.Rossco
do you have to clean the gun between each gel coat application if you are doing a large area ?
As long as the gel coat is live and the pot emptied between each pour you can continue.Cleaning is required prior to gel setting.Cheers Ross
Hi ! How are you today, My Name is Mr.Herman Woods. I have to RC BOATS ! I WAS WATCHING YOUR VIDEO. AND I SAW YOUR GELCOT GUN SPRAYER . I SAW A GUN LIKE THAT ! , BUT I THINK IT IS A DIFFERENT MODEL . BUT IT COME WITH 3 NOZZLE"S .AND THAT LAST NOZZLE ! IS A 2.5MM .THEY SAY ! IT WILL PAINT AUTOMOTIVE .BUT IT DID NOT SAY ANYTHING ABOUT GELCOT . SO ! I WONTED TO ASK YOU ! IF MY NOZZLE IS A 2.5 .WILL I BE ALL RIGHT ! WITH THE GUN .ITS A HVLP GUN . OUR ! I NEED TO GET WHAT YOU HAVE.!! CAN YOU LET ME KNOW.THANK YOU FOR YOUR TIME .MR.H.WOODS ! THANK YOU .
Say you were shooting a big mould, not quite as big as yours. And didn’t have a proper resin gun, do you reckon it’s possible to do with 3 of these guns and have a mixer person, a cleaner and a sprayer. Do you like these guns better than the other gelcoat guns that have the paper inserts and the cup on the back of the gun that are sold as “gelcoat guns”
I honestly think a G100 cup gun is a much better solution for larger moulds.Hvlp guns are excellent small job tools and gear for repairs etc You would need to be constantly changing cups with a cup gun and I have sprayed moulds with 4-5 cups full at a sitting.The key is keeping pressure constant and moisture out of the air feed A dryer or gravity drain with moisture trap/ filter is an essential in any case.Rossco.
@@thecompositesshop cheers mate thanks for the info 🤙🏻
Top tutorial Rossco..👍🏼👍🏼👍🏼