Thanks! Took me a second to figure out how to put the extractor back as I couldn't see it in the vid. I have the exact same rifle. First lever action. I was afraid I was going to screw it all up. I didn't, thanks to you.
Just got myself a Henry 410 Axe for my birthday. Absolutely love it. It's my 1st lever gun and for sure not my last. This video cleared up my confusion on how to clean it. Now she's clean as new and ready for the range again. If you ever get the chance, get one. The 410 Axe with rifled slugs is awesome to shoot. Lower recoil than you expect and very accurate for a smooth bore.
Great job! When I got my Henry BB 357, it didn’t come with any cleaning details, and I viewed other vids that said to pull all bolts and drop the lever and trigger to get the bolt out. The tension bolt was a booger to get back lined up putting it back together. You tip on just pulling 1 bolt for the lever and toggling the hammer to slip the bolt out was pure gold. Thanks for the vid!
Thanks for the video. I have a Henry Big Boy in 357 magnum that I put 3,000 rounds through that I never took apart because the manual said you don’t need to. I broke the firing pin and was forced to take it apart. This vid helped
It's really unlike Henry to tell you that you don't need to take down the rifle for cleaning..how else are gonna get to clean those tight spots..I'm happy this helped you out.
I just bought a Henry long ranger 308 magazine fed. The manual says to not take it apart for for cleaning because it is a specialized finely fitted mechanism. Says to use a pull through type cleaning rod so you don’t push dirt back into the chamber and action. Also that just wiping out the action and cleaning the barrel is enough to keep it operating properly. We’ll see how that goes
I never pull the cleaning tool back towards the receiver. Good way to pull debris back into the receiver end. I always go one way in and out the end of the barrel, every time.
as i demonstrate i took meticuous attention to detail when cleaning the reciever, even when cleaning rear to front it all comes out in the end my concern is more to save the barrel crown. thanks for watching.
One of the best explanations of how to clean a Henry on the interwebs…it’s just too bad you can’t see anything because your camera angles are all screwed up and about 60% of the work happens off camera…lol. Still found it very valuable…that’s how good you are at explaining things!!!!!
Glad to see another perspective. I have a Big Boy and the manual as well as videos at the time advised a tear down. All I can see from that point is sooner or later the stock screws will become loose. I use a bore snake and every 500 rounds I'll do a more complete clean. All of my firearms are cleaned after returning from the range.
Such beautiful rifles, I have one in .357 / .38 Sp which is the Big Boy Carbine with hex barrel and the big loop handle. It is such a joy to shoot just plain iron sights. I plan on at least two more Henry rifles not sure which yet and they are expensive but of such quality it is worth it. .
@@Ford360CID Haven't heard about that, not sure which rifle you are speaking of ... the one I own? Mine is the Big Boy Carbine in brass without side loading gate which doesn't bother me using it for plinking. I have a 1976 Marlin 336C in .30-30 for "hunting".
Finally someone else that: SAVES OLD TOOTHBRUSHES & T-SHIRTS to Clean their match FIREARMS PS USE THAT FLITZ IN YOUR BORE THEN DRY PATCH IT, HOPPES THEN DRY PATCH TIL CLEAN! You'll be a Amazed!
Thank you for the video. I just got the brass receiver version, and want to take good care of it. I've got a Otis cable pull cleaning kit coming, but plan to take the bolt out as you did to use a rod every 4th or 5th cleaning. Like you say, it's a good chance to inspect and lube the bolt.
rob why go half way on the cleaning when the henrys can be cleaned efficiently as a bolt action im glad my video helped you make a good cleaning choice.
Thanks for the video. I am kinda just learning how to clean my rifles. As i just got some. So, i would like to keep them for years or as long as i am living.
@@Ford360CID the one that I got yesterday. It will be my fifth lever. I started looking at them years ago and thinking about the ok cowboy days. I even bought a scope to put on one. But it will take away from the cowboy look. So, I will put it on another one that I have. Yes, some people are right. Henry rifles are kinda expensive. But they are made in America. I will pay more for something that is made here.
Dude you're killing me with that screwdriver being rolled underneath the stock! Ahhhhhh! Lol. Just kidding. Nice video! I do also just go from the breach end one way through , remove the patch and use a clean one coming back, but that's just me. To each his own.
Excellent! I didn't actually see you drop the ejector into the slot...or did I miss that? [I'm a newbie and def want to get THAT right!] Thanks so much~~~ Now, I think that I really need to get the .357 w/ the side-gate. Stuck between the Round barrel or Octagon......Choices/Choices~~~ ;-)
Any links on bolt disassembly. My 9 year old big boy 45c started having ejection issues. Called Henry, no help… nothing on net …… I field strip and clean after each use. But bolt had obvious carbon build up I couldn’t get at ( extractor etc ). Needs disassembly …..or chemical cleaning ? Any suggestions ? Thanks
Thank you for the video all the others on the Henry show taking the hole gun apart, glad to see you can do it the same as a marlin 444 . I think I will get the case hardened carbine now I know it is easy to clean and you do not have to take the hole gun apart to clean. I love my 444 marlin, but do not like the 1-38 twist of the 44 mag 1894 or the action of the 1894 wish marlin still made a 44 mag in the 336 platform. The only thing I wish Henry made a 44 mag carbine with a loading gate. But will take it over the 1894 and 1-38 twist.
Hey thanks for the video, just got a Henry 357/38spl and wanted to clean and lube it before I took it to the range. Question for you please - Do you use the Flitz paste on the gun metal also. My Henry is a Big Boy Classic and has the brass barrel band, brass receiver and brass tubular magazine.
i had several request for the ejector reassembly but working the camera alone made it difficult to do, im gonna do a another henry video soon and i will include that in as well. thanks for watching
You did great job, I am glad to see, that cleaning Henry rifle is as easy as cleaning Marlin. Finally I got good argument to buy Henry - because full dissasembly cleaning was quite discouraging.
I just bought a Henry 45-70 X and mine it has like a knob on the rear bottom of the bolt which touches the hammer making it stall when closing the action. Now, is this normal or can I take that "knob" off so I can have a smooth working action?
i dont live there any more, now my yard is have the size but decent but i like my new garage/man cave its more bigger i'll be doing my video's in there and my master bedroom. thanks for watching.
Didn't even wipe the cleaning rod after it falls on the ground.. Shoved it straight back in there! Good video, basic clean. Not really a fan of running the cleaning cloth forwards then backwards, new pad each time it comes out the end of the barrel. Each to their own though. Thanks for posting.
@@BigLisaFan that’s good practice to keep, but outdated. Gun powder is much cleaner now and you really only need to clean your guns after every 3 trips to the range or depending on how much you shoot after 500 or so rounds.
@@bsh0718 I was taught in the military, that when finished shooting, first thing you do was clean your rifle then you can eat. That has carried on to my personal life. Shoot, clean, ready for next time.
lead bullets 4 life thanks! Really looking forward to sending a few rounds downrange with this one! It's the 45-70 AW. Love the nickel plated finish and was really impressed with the smooth action.
Yes made in America or not at all. Wearing my Henry hat and drinking from my Henry mug. Have too lock my door now with my Henry keychain. This is Rich leaving Donna Donna. Who me I'm not a Henry fanboy, much!!
Heard of it plenty, unlike other RUclips publishers they use professional grip personnel to do their videos, everything I do comes out of my pocket, no sponsorship, no donations, no camera assistance or assistant, no fancy studio where the Iighting is the best...no sir I do an honest job without any help..so yes I've heard of camera angles and light..what about it?
thank you for comment Robert, the ammunition i use is a cast bullet with a soft home made lube and velocities are under 1000 fps so the soft lube leaves a wax residue each time the bullet is fired and the next round has the benefit of the round before it acting as a self cleaning barrel,in my part 2 video i use a dry patch to remove the residue out of the barrel i fired 200 lubed cast bullets before making the video and the barrel looked like it hadnt been fired...so to answer your question it would depend alot on the type ammo your firing such as jacketed ammo those you can shoot all day my recommendation is to look down the bore every 50 rounds to see if you have any heavy fouling or every range session after you get home.
@@roberttsang6595 i love my lever's i also have the #0001 and the golden boy .22lr i want to also show case those 2 soon as well, i look at these lever guns and they were once the m-16's of the past warfare i would love to get another henry with new side loading gate in either .44 or 45 long colt.
I got a cleaning patch (cut up t shirt square) stuck in mag tube right in the action where a new round would be feeding into chamber. Any advice how to get it out?
@@Ford360CID i guess that's my question. Do you think I'll need to disassemble from lever and forend? The lever and stock? All 3? Or just from the lever
@@Ford360CID also I've never broke the rifle down or any lever action actually. It was my first day getting it home and went to clean it and bam. I knew it was going to happen and still did it anyways. Dumb i know
@@Tread505 this is not uncommon especially with lever guns unlike bolt actions so dont feel like it was a rookie mistake this is all part of the learning process of the differences in rifle actions and types, and how to go about cleaning them with the correct jag types, let me know how it goes.
Ugh, not so easy with an Evil Roy as this one. 5 screws to get the cover off, and then I guess that's how to get to the lever screw to remove it. I'll keep looking until I find one for Evil Roy cleaning. The Henry in this video is similar to the Marlin, very easy to clean compared to mine.
@@Ford360CID I did find one on the Evil Roy type rifles. Remove the stock screw and stock, then the 4 cover screws and slide the cover back and then the bolt comes off. Got mine all pulled apart, including the firing pin and extractors and got it all nice and clean and put back together. If you haven't done one yet, show how the bolt is taken apart and cleaned, especially on the rimfire. Pretty interesting setup. A lot of carbon builds up under the kicker pin and can cause jams if not cleaned regularly.
Does anyone else have issues unscrewing the initial screw for the tension on the lever? It's the first time cleaning my new H009 and I can't get the screw undone!
@@pitman0001 I definitely marred the screw a little, but it's just some scratching and hasn't stripped. I'm not sure if I should just bring it to a local shop or keep trying.
on your bolt you have an extractor claw which grabs the rim of the shell and it aids in pulling the spent shell out... on the left side of your reciever you have a piece of metal that protrudes forward when the left side of your spent casing hits this protruding piece of metal it forces the spent case to turn in the right direction and out of the gun...a very simple device.
Yeah I have tried but it does not. I called Henry and they told me it can not come apart like that. Maybe has to do with year of manufacturing. Oh well I guess, would be a lot more convenient to clean.
i just saw a disassembly video on the henry big boy, by gerry beathard and you were right you pretty much have to remove a lot more parts before you can remove the bolt.
Contrary to popular belief, One can clean a lever gun Without disassembly. Just be careful of the crown.. Use a good rod and clean from the bore end down. Full cleaning can be done every couple of months...
Yeah, I use a bore snake which can be inserted without taking anything apart. 1 or 2 pulls with solvent, 1 or 2 dry, and it's good as new! For cleaning the chamber one can use a q-tip, then wipe everything down with a pre-oiled gun cloth and you're done. The full cleaning can be done when you want to make love to the rifle. Not literally of course. That would be weird and disturbing. Edit: I misread your comment. I would advise against sticking anything from the bore end. A good bore snake is 10 bucks and does the job better anyways.
You really don't want to go back and forth you just bring all that grime back into the breach where it is even more difficult to clean. So how you ask then. Use your imagination.
Congratulations on your new purchase you're going to enjoy it like it was just a regular Centerfire rifle Smooth Bore it don't matter it's a lever action that's what matters.
The last part of the video-about reassembly-goes much too quickly. You need to be much more careful in showing replacing the extractor and inserting the bolt.
You use a soft towel to protect your rifle, but man you are clumsy, your stock sitting on your screw deiver, banging about your barrel etc etc. Apart from that, not a bad video.
After years and years of wearing out my thumb loading my Marlins I bought a Henry and prefer the tube. I just bought another Henry in 45-70. Of course I shoot every weekend and reload ammunition. Sometimes I shoot two to three times a week to include lever actions. You don’t shoot enough if you haven’t worn out your thumb or cut it on those stuff sharp loading gates. I’ll take the tube all day long!
I appreciate your effort, but watching you bash the gun around, and not move the lever screw safely out of the way, was too much. Also you can get nylon bristle bore brushes.
yes! but there was no editing like some others cleaning and firearm and handling video's that hide their mistakes and not put it in real time, there alot you don't see in other cleaning videos where others drop tools scratch the blueing or even drop the gun because long guns are well! long and clumsy, have a great rainy sunday and thanks 4 watching.
Very poorly done as I find the ejection spring replacement not even mentioned in your reassembly. It’s the most important part of the reassembly, the hardest to get to an understand and you just skipped right over it. I would not recommend you for your skills to anyone based on this. Took me a while to figure out how to do it, but I did it on my own with no help from you..
not quite that simple with levers there a lot of channels that need to be cleaned and lubed to keep hidden moisture out not to rust out and the brass needs to be polished regularly finger prints and moisture will eat at that brass tube.
@@Ford360CID If we lived in Viet Nam where the humidity was 100% rust might be an issue.....it wasn't an issue for the cowboys in 1880, especially with the complex Winchesters that can't be taken apart and cleaned. This isn't Marine boot camp here!!!
@@chadhaire1711 then i would say ( improvise over come and adapt like a true marine would.) nothing is out of reach with humidity whether in a safe or on a wall mounted rifle rack get the lead out and keep your weapons well lubed and oiled.
@@Ford360CID I knew it..a jarhead!!!! My Glock and GI 1911 1917 US Army issue has only been cleaned twice in 20 years....and NO lube..just a drop of oil on a rag for a wipedown! TRUE combat guns...
Thanks! Took me a second to figure out how to put the extractor back as I couldn't see it in the vid.
I have the exact same rifle. First lever action. I was afraid I was going to screw it all up. I didn't, thanks to you.
Im glad it worked out for you.
Just got myself a Henry 410 Axe for my birthday. Absolutely love it. It's my 1st lever gun and for sure not my last. This video cleared up my confusion on how to clean it. Now she's clean as new and ready for the range again. If you ever get the chance, get one. The 410 Axe with rifled slugs is awesome to shoot. Lower recoil than you expect and very accurate for a smooth bore.
Great job! When I got my Henry BB 357, it didn’t come with any cleaning details, and I viewed other vids that said to pull all bolts and drop the lever and trigger to get the bolt out. The tension bolt was a booger to get back lined up putting it back together. You tip on just pulling 1 bolt for the lever and toggling the hammer to slip the bolt out was pure gold. Thanks for the vid!
it was my pleasure i love my henry and you will too.
Thanks for the video. I have a Henry Big Boy in 357 magnum that I put 3,000 rounds through that I never took apart because the manual said you don’t need to. I broke the firing pin and was forced to take it apart. This vid helped
It's really unlike Henry to tell you that you don't need to take down the rifle for cleaning..how else are gonna get to clean those tight spots..I'm happy this helped you out.
I just bought a Henry long ranger 308 magazine fed. The manual says to not take it apart for for cleaning because it is a specialized finely fitted mechanism. Says to use a pull through type cleaning rod so you don’t push dirt back into the chamber and action. Also that just wiping out the action and cleaning the barrel is enough to keep it operating properly. We’ll see how that goes
@@lyle7657 sounds quite simple enjoy it.
Thanks for the video!! Just bought a Henry H009 30-30 yesterday and will be taking it to the farm to sight it in today. Great info!!!
I have a #2 video replacing the ejector I should have gotten the 30-30 as well I love that cartridge.
Thanks again Double Clutch -- keep coming back to this -- appreciate the help !!
I never pull the cleaning tool back towards the receiver. Good way to pull debris back into the receiver end. I always go one way in and out the end of the barrel, every time.
as i demonstrate i took meticuous attention to detail when cleaning the reciever, even when cleaning rear to front it all comes out in the end my concern is more to save the barrel crown. thanks for watching.
You actually want to do it that way to save the rifling and barrel crown.
@@luke8222 Is correct. If possible you want to clean from the receiver end to save the barrel crown. In some cases you can't, but with these, you can.
One of the best explanations of how to clean a Henry on the interwebs…it’s just too bad you can’t see anything because your camera angles are all screwed up and about 60% of the work happens off camera…lol. Still found it very valuable…that’s how good you are at explaining things!!!!!
yes! that why i made a part 2 go an sub and you'll be able to find it thanks4 watching.
Glad to see another perspective. I have a Big Boy and the manual as well as videos at the time advised a tear down. All I can see from that point is sooner or later the stock screws will become loose. I use a bore snake and every 500 rounds I'll do a more complete clean. All of my firearms are cleaned after returning from the range.
less cleaning work when you get home.
I got a Henry 30/30 2 month ago. My first one . I'm glad for videos like this one. Thanks
I just 💘 love the 30-30!! I wish i still had it, i payed 249$ in 1994 with the 24" barrel.
You should try Ballistol. Great for cleaning, non toxic and does not hurt wood or other materials.
I got myself a Henry Longranger 243 and I love it
Thanks for the information on this. The wife's chimes make for good ambient sounds..
I also have a pt 2 placing the ejector.
I love the smell of Hoppe's in the morning....it smells like Victory! 👍👍
i use hoppes as an after shave, nah just kidding.
@@Ford360CID
Lol! It's good stuff, used it since I got my first rifle at 8yo.
Such beautiful rifles, I have one in .357 / .38 Sp which is the Big Boy Carbine with hex barrel and the big loop handle. It is such a joy to shoot just plain iron sights. I plan on at least two more Henry rifles not sure which yet and they are expensive but of such quality it is worth it. .
@@Ford360CID Haven't heard about that, not sure which rifle you are speaking of ... the one I own? Mine is the Big Boy Carbine in brass without side loading gate which doesn't bother me using it for plinking. I have a 1976 Marlin 336C in .30-30 for "hunting".
I thought you were referring to the Lyman Plains rifle
@@Ford360CID No sorry. :)
I finally got my 357 yesterday. The last one for right now. I never thought that I would have so many henrys.
The part I am most worried about is getting the ejector back in and I didn't see you do that.
Its difficult to show so check out my pt 2 it shows some what better
Thank you sir. Nicely done and very helpful.
My pleasure thanks for watching
Thanks, definitely helped me to remove the bolt and extractor for my first cleaning.
Plenty of comments mentioned That Henry doesn't provide cleaning instructions and that shouldn't be glad this was a help to you.
Thank you Sir for the Video on how to clean my Henry Big Boy Rifle 357/38SP Clear and Understandable!
i have a pt 2 which is much shorter thanks 4 watching.
Thank you for the Video!! Was terrified to do anything more than swab the barrel. Now its properly cleaned and oiled.
thanks 4 watching you must see my pt-2 video it's under 10 minutes long.
Finally someone else that:
SAVES OLD TOOTHBRUSHES & T-SHIRTS to Clean their match FIREARMS
PS USE THAT FLITZ IN YOUR BORE THEN DRY PATCH IT, HOPPES THEN DRY PATCH TIL CLEAN! You'll be a Amazed!
i use mothers aluminum polish but i do have flitz on hand, once the bolt is removed it's like cleaning a bolt action...quite simple.
Nice video, but upon reassembly he forgot to put the extractor back in. I don't think it'll work too good without it.
Thank you for the video. I just got the brass receiver version, and want to take good care of it. I've got a Otis cable pull cleaning kit coming, but plan to take the bolt out as you did to use a rod every 4th or 5th cleaning. Like you say, it's a good chance to inspect and lube the bolt.
rob why go half way on the cleaning when the henrys can be cleaned efficiently as a bolt action im glad my video helped you make a good cleaning choice.
Thanks for the video. I am kinda just learning how to clean my rifles. As i just got some. So, i would like to keep them for years or as long as i am living.
they will out live you with your meticulous care and attention to detail...long live the lever's!!
@@Ford360CID the one that I got yesterday. It will be my fifth lever. I started looking at them years ago and thinking about the ok cowboy days. I even bought a scope to put on one. But it will take away from the cowboy look. So, I will put it on another one that I have. Yes, some people are right. Henry rifles are kinda expensive. But they are made in America. I will pay more for something that is made here.
Thank you very much! I'm on my way for a day of shooting. My .22 LR Henry is a virgin so this is really helpful and right on time :-)
I also have videos on the Henry #1
Awesome video! Good instructions and tips.
I also have a pt 2 thanks4watching
Dude you're killing me with that screwdriver being rolled underneath the stock! Ahhhhhh!
Lol. Just kidding. Nice video!
I do also just go from the breach end one way through , remove the patch and use a clean one coming back, but that's just me. To each his own.
the screwdriver under the stock. A piece of me died.
You got to get this rifle !
can you do a video from the other side showing how you got the extractor out?
Looks like it is the same as a Marlin. Nice.
Excellent! I didn't actually see you drop the ejector into the slot...or did I miss that? [I'm a newbie and def want to get THAT right!] Thanks so much~~~ Now, I think that I really need to get the .357 w/ the side-gate. Stuck between the Round barrel or Octagon......Choices/Choices~~~ ;-)
I have a 2pt video and I show the erector assembly.
Any links on bolt disassembly. My 9 year old big boy 45c started having ejection issues. Called Henry, no help… nothing on net …… I field strip and clean after each use. But bolt had obvious carbon build up I couldn’t get at ( extractor etc ). Needs disassembly …..or chemical cleaning ? Any suggestions ? Thanks
Very handy thanks kindly!
Thank you! I got a .44 henry for my eagle scout rank and the manual that came with it don’t explain anything.
Hopefully the 44 steel is the same set which i believe it is congratulations and good luck.
Make sure you are using Hollow Ground screwdrivers normal screw drivers will ruin your screws.
How do you guys feel about steel cleaning rods V plastic, aluminum etc?
Thank you for the video all the others on the Henry show taking the hole gun apart, glad to see you can do it the same as a marlin 444 . I think I will get the case hardened carbine now I know it is easy to clean and you do not have to take the hole gun apart to clean. I love my 444 marlin, but do not like the 1-38 twist of the 44 mag 1894 or the action of the 1894 wish marlin still made a 44 mag in the 336 platform. The only thing I wish Henry made a 44 mag carbine with a loading gate. But will take it over the 1894 and 1-38 twist.
I have a pt 2 as well and thanks for watching.
Henry has the Big Boy X (all black) in 44 Mag with a side loading gate.
Good presentation, thumbs up to you.
thank you for your comment do you own a henry?
Are all levers that easy to clean and lubricate ?
Thanks for this.
Your welcome thanks for watching
using a bore guide is definately a positive on lever guns.Looks like Henry levers have less parts than Marlin's.
Hey thanks for the video, just got a Henry 357/38spl and wanted to clean and lube it before I took it to the range. Question for you please - Do you use the Flitz paste on the gun metal also. My Henry is a Big Boy Classic and has the brass barrel band, brass receiver and brass tubular magazine.
Good video,on the general cleaning. Wish you could have shown the ejector. However very ,very helpful on the henry. Thanks ,,
i had several request for the ejector reassembly but working the camera alone made it difficult to do, im gonna do a another henry video soon and i will include that in as well. thanks for watching
You did great job, I am glad to see, that cleaning Henry rifle is as easy as cleaning Marlin. Finally I got good argument to buy Henry - because full dissasembly cleaning was quite discouraging.
I just bought a Henry 45-70 X and mine it has like a knob on the rear bottom of the bolt which touches the hammer making it stall when closing the action. Now, is this normal or can I take that "knob" off so I can have a smooth working action?
under Craigs gun channel he announced a henry 45-70 recall this was 7 months ago...you may want to call their customer service line.
Nice big yard!
i dont live there any more, now my yard is have the size but decent but i like my new garage/man cave its more bigger i'll be doing my video's in there and my master bedroom. thanks for watching.
Didn't even wipe the cleaning rod after it falls on the ground.. Shoved it straight back in there! Good video, basic clean. Not really a fan of running the cleaning cloth forwards then backwards, new pad each time it comes out the end of the barrel. Each to their own though. Thanks for posting.
you have 2 sides of the cleaning patch, the forward stroke gets absorbed with fouling, then the back side of the patch takes over.
@@Ford360CID yep. That's no problem. Great stuff mate. I recently purchased a Henry 45-70 so this video certainly did help me out!
i'm elated that it helped you out, you sound like your from down under where do you hail from? i spent a week in Perth and fremantel.
@@Ford360CID yeh mate, I'm Aussie.! From New South Wales! Keep up the videos mate, they're great!
Thank you
@gustavoaramirez9673 I have a pt 2 video with more clarity
How do you install the ejector as it fell out and you don’t show how or when to put it back in
Thanks for the video! I learned a lot.
CaptainBadHorse Thanks for watching.
Nice angle
I grab the rod by its handle so it can spin inside the barrel. That's why the rods rotate!!!
Thanks. Great video
CPOTuggs Thanks you for watching
Sheeew!!!!! Remind me to not let you clean my gun. That screwdriver has to be hard on the walnut stock!!! 🤣🤣
not a scratch on it but i might clean your bike Hi Hi hI.🏍
What about your trigger assembly and hammer? Those have to be cleaned.
i have a more detailed cleaning of the henry steel in my part 2 video.
Thankyou i have just Purchased a Henry H001 After about how many Rounds does the Rifle need to be Cleaned?
Clean your rifle every time when you have finished shooting for the day.
@@BigLisaFan that’s good practice to keep, but outdated.
Gun powder is much cleaner now and you really only need to clean your guns after every 3 trips to the range or depending on how much you shoot after 500 or so rounds.
@@bsh0718 I was taught in the military, that when finished shooting, first thing you do was clean your rifle then you can eat. That has carried on to my personal life. Shoot, clean, ready for next time.
What caliber is your Henry? I have a 45-70 that I just got and was looking for cleaning tips!
Thanks for sharing!
its the henry steel .357/38spl and i love it when i shoot target lead loads at 50 yards all in the black, i have that video coming up soon.
lead bullets 4 life thanks! Really looking forward to sending a few rounds downrange with this one!
It's the 45-70 AW. Love the nickel plated finish and was really impressed with the smooth action.
remember!! if its not made in america then its not made at all!!!!
lead bullets 4 life you are right!! This is a quality rifle!
Yes made in America or not at all. Wearing my Henry hat and drinking from my Henry mug. Have too lock my door now with my Henry keychain. This is Rich leaving Donna Donna. Who me I'm not a Henry fanboy, much!!
I have the same gun in 45 colt and can not remove the bolt like you did. I have to fully disassemble the gun.
IT SHOULD RELEASE THE SAME WAY, PUSH DOWN ON THE HAMMER AND IT SHOULD HELP RELEASE THE BOLT.
I also have the same gun in 45 colt and my bolt will not come out like you showed.
I missed you putting back the ejector
I have a pt 2 video on the ejector assembly
Will this method of disassembly work for a Henry Long Ranger as well?
because the ranger is a lever gun there shouldn't be an issue, just that it has a magazine well instead of a tube.
Ever hear of lighting and camera angles?
Heard of it plenty, unlike other RUclips publishers they use professional grip personnel to do their videos, everything I do comes out of my pocket, no sponsorship, no donations, no camera assistance or assistant, no fancy studio where the Iighting is the best...no sir I do an honest job without any help..so yes I've heard of camera angles and light..what about it?
What's the recommended cleaning after how many rounds ?
thank you for comment Robert, the ammunition i use is a cast bullet with a soft home made lube and velocities are under 1000 fps so the soft lube leaves a wax residue each time the bullet is fired and the next round has the benefit of the round before it acting as a self cleaning barrel,in my part 2 video i use a dry patch to remove the residue out of the barrel i fired 200 lubed cast bullets before making the video and the barrel looked like it hadnt been fired...so to answer your question it would depend alot on the type ammo your firing such as jacketed ammo those you can shoot all day my recommendation is to look down the bore every 50 rounds to see if you have any heavy fouling or every range session after you get home.
@@Ford360CID Thanks for your reply - The Henry BB 357 is deadly accurate and fun to shoot.
@@roberttsang6595 i love my lever's i also have the #0001 and the golden boy .22lr i want to also show case those 2 soon as well, i look at these lever guns and they were once the m-16's of the past warfare i would love to get another henry with new side loading gate in either .44 or 45 long colt.
Would anyone recommend a field strip and clean w oil of your virgin Henry before first firing?
a wipe down and a barrel swab is good enough out of the box.
What is a high pressure sigh? Were do you look for that, what parts? Thanks
Bulged cases bright spots on your ejected cases glattened or pierced primers
Amazing its like this is the first time this guy is cleaning a gun, amazing!!
I got a cleaning patch (cut up t shirt square) stuck in mag tube right in the action where a new round would be feeding into chamber. Any advice how to get it out?
have you tryed breaking down the lever action?
@@Ford360CID i guess that's my question. Do you think I'll need to disassemble from lever and forend? The lever and stock? All 3? Or just from the lever
@@Ford360CID also I've never broke the rifle down or any lever action actually. It was my first day getting it home and went to clean it and bam. I knew it was going to happen and still did it anyways. Dumb i know
@@Tread505 start with the lever its the easiest this way you have better access to the stuck patch.
@@Tread505 this is not uncommon especially with lever guns unlike bolt actions so dont feel like it was a rookie mistake this is all part of the learning process of the differences in rifle actions and types, and how to go about cleaning them with the correct jag types, let me know how it goes.
No bore guide?
I cringed every time I heard it....
Ugh, not so easy with an Evil Roy as this one. 5 screws to get the cover off, and then I guess that's how to get to the lever screw to remove it. I'll keep looking until I find one for Evil Roy cleaning. The Henry in this video is similar to the Marlin, very easy to clean compared to mine.
Yes they can be a cinch or troublesome
@@Ford360CID I did find one on the Evil Roy type rifles. Remove the stock screw and stock, then the 4 cover screws and slide the cover back and then the bolt comes off. Got mine all pulled apart, including the firing pin and extractors and got it all nice and clean and put back together. If you haven't done one yet, show how the bolt is taken apart and cleaned, especially on the rimfire. Pretty interesting setup. A lot of carbon builds up under the kicker pin and can cause jams if not cleaned regularly.
@@acdii I'll need to do that with my Henry triple zero one
Good info and video, just wish you had a little more close-up for details. Thank you
Thanks4 your comment sir i do have second video on reassembly on the henry steel ejector reassembly.
Funny, my cleaning method is almost identical.
theres really nothing to it!! its like cleaning a bolt gun.
How do you remove the forestock/ hand guard? It is not intuitive.
not nessesary to remove.
@@Ford360CID unless you get caught in the rain
Have you tried the Lewis lead remover system to remove the lead or a chore boy wrapped around a brush to remove lead?
i just bought one of those on ebay for 21$ for the 9mm/38spl.
Does anyone else have issues unscrewing the initial screw for the tension on the lever? It's the first time cleaning my new H009 and I can't get the screw undone!
It's sticky the first time you unscrew it. Careful not to strip!
@@pitman0001 I definitely marred the screw a little, but it's just some scratching and hasn't stripped. I'm not sure if I should just bring it to a local shop or keep trying.
What happened to the rejector?
LOOK AT 13:30
Never showed how to put the ejector back in!!!!
check out 13:30 minutes
A little tricky but just do the process in reverse...
That was the biggest bitch to figure out ...
Honestly looks like a "Marlin" style action
@@tjmooremusic Do the process you can't see him do in reverse, great suggestion.
What about the pin you took out?
blackhawk2429. You place it back with a needle nose pliers or slide it in until the notch enters the hole then carefully place in your slide and viola
@@Ford360CID I see! thanks for demonstration.
BIG BOY!
Thank you. :-)
Ian Fenn happy to Help Thanks for watching
I have a brand new Henry Big Boy 45 colt, can't wait to shoot it, and now I can clean it with confidence. All the best.
The ejector???
on your bolt you have an extractor claw which grabs the rim of the shell and it aids in pulling the spent shell out... on the left side of your reciever you have a piece of metal that protrudes forward when the left side of your spent casing hits this protruding piece of metal it forces the spent case to turn in the right direction and out of the gun...a very simple device.
or see lever action cleaning pt-2
Like the wind chimes in the back ground.
thank you sir they add a bit of ambiance to the back ground.
I got mine in 44 win mag and there is a slight malfunction when loading the gun ! Was wondering if anyone got some similar problems with theirs
is it loading down the chamber shute or is it the racking of the lever action that starts the problem?
Anyone know a video that shows you how to get your level back in if it won't seat right
Xander .357 you mean the lever, there other take down videos on that very subject.
Yeah I have tried but it does not. I called Henry and they told me it can not come apart like that. Maybe has to do with year of manufacturing. Oh well I guess, would be a lot more convenient to clean.
this is quite interesting, it appears that not all henry lever actions are same across the board, have you tryed any other vid's on the suject?
i just saw a disassembly video on the henry big boy, by gerry beathard and you were right you pretty much have to remove a lot more parts before you can remove the bolt.
Contrary to popular belief,
One can clean a lever gun
Without disassembly.
Just be careful of the crown..
Use a good rod and clean from the bore end down.
Full cleaning can be done every couple of months...
Yeah, I use a bore snake which can be inserted without taking anything apart. 1 or 2 pulls with solvent, 1 or 2 dry, and it's good as new! For cleaning the chamber one can use a q-tip, then wipe everything down with a pre-oiled gun cloth and you're done. The full cleaning can be done when you want to make love to the rifle. Not literally of course. That would be weird and disturbing.
Edit: I misread your comment. I would advise against sticking anything from the bore end. A good bore snake is 10 bucks and does the job better anyways.
New friend lodi,m8
..
Ganyan din me ,tulungan t u
..... .... ,.,. ,.,
🙂👍☕
Just like cleaning a 336
pretty much!! thanks for watching, do you like 213gn 38spl's? watch my recent vids.
You really don't want to go back and forth you just bring all that grime back into the breach where it is even more difficult to clean. So how you ask then. Use your imagination.
Ahhh that poor wood stock on the screwdriver
I have 2 more tear down and shooting videos on the same rifle thanks4 watching.
Lousy cleaning method. To each his own.
Congratulations on your new purchase you're going to enjoy it like it was just a regular Centerfire rifle Smooth Bore it don't matter it's a lever action that's what matters.
Too freaking fast! What extractor? Where...how...?
Gp to my part 2 video its more detailed
The last part of the video-about reassembly-goes much too quickly. You need to be much more careful in showing replacing the extractor and inserting the bolt.
Try watching my part 2 its more detailed bettet yet watch my reassembly of the extractor of the 357 magnum steel video
You use a soft towel to protect your rifle, but man you are clumsy, your stock sitting on your screw deiver, banging about your barrel etc etc. Apart from that, not a bad video.
Thanks for watching,.
You may know Henry rifles but not enough to teach you missed a critical step. Support had to help me recover
Bore snake
If it doesn't load on the side it's a no go.
EVEN THE ORIGINAL HENRYS DIDNT HAVE A SIDE LOADER EITHER.
After years and years of wearing out my thumb loading my Marlins I bought a Henry and prefer the tube. I just bought another Henry in 45-70. Of course I shoot every weekend and reload ammunition. Sometimes I shoot two to three times a week to include lever actions. You don’t shoot enough if you haven’t worn out your thumb or cut it on those stuff sharp loading gates. I’ll take the tube all day long!
I appreciate your effort, but watching you bash the gun around, and not move the lever screw safely out of the way, was too much. Also you can get nylon bristle bore brushes.
yes! but there was no editing like some others cleaning and firearm and handling video's that hide their mistakes and not put it in real time, there alot you don't see in other cleaning videos where others drop tools scratch the blueing or even drop the gun because long guns are well! long and clumsy, have a great rainy sunday and thanks 4 watching.
Very poorly done as I find the ejection spring replacement not even mentioned in your reassembly. It’s the most important part of the reassembly, the hardest to get to an understand and you just skipped right over it. I would not recommend you for your skills to anyone based on this. Took me a while to figure out how to do it, but I did it on my own with no help from you..
I have a part 2 with the ejector assembly.
Too much work...just run a bore snake and be done
not quite that simple with levers there a lot of channels that need to be cleaned and lubed to keep hidden moisture out not to rust out and the brass needs to be polished regularly finger prints and moisture will eat at that brass tube.
@@Ford360CID If we lived in Viet Nam where the humidity was 100% rust might be an issue.....it wasn't an issue for the cowboys in 1880, especially with the complex Winchesters that can't be taken apart and cleaned.
This isn't Marine boot camp here!!!
@@chadhaire1711 then i would say ( improvise over come and adapt like a true marine would.) nothing is out of reach with humidity whether in a safe or on a wall mounted rifle rack get the lead out and keep your weapons well lubed and oiled.
@@Ford360CID I knew it..a jarhead!!!! My Glock and GI 1911 1917 US Army issue has only been cleaned twice in 20 years....and NO lube..just a drop of oil on a rag for a wipedown! TRUE combat guns...
@@chadhaire1711 close!! u.s. navy cause you said this isn't marine bootcamp i just thought you were a former marine.
Painful to watch
I have a pt 2 as well 10 minutes