Mitsubishi L200 Body lift - part 1
HTML-код
- Опубликовано: 6 сен 2024
- 1 inch - 2,5 cm body lift.
Music:
Anno Domini Beats - Awaken - Hip Hop & Rap | Inspirational HOTTEST SOUNDTRACK !!!
Free Music for Commercial Use
• Video
Instagram: egmusic16
/ freemusiceg16
/ ncmmusic16
soundcloud.com/ncm-free-music
ncmender...
Intro music:
Infinity by Broken Elegance 🎩 / brokenelegance
Creative Commons - Attribution 3.0 Unported- CC BY 3.0
creativecommons....
Music provided by Audio Library • Infinity - Broken Eleg...
Top
Szia. Az amúgy is nagyon berozsdásodott dolgokat forgó drótkefével megdolgoztam volna, majd Brantho Korrux-szal lezártam volna ;) De így is nagyon jó videó, és az L200 tetszik. Melegszívű üdvözlet
Szia! Köszi a tippet, de nem ugyanazok a csavarok mentek vissza, amiket kivettem, mindenhova új került.
One of the many dangers of a L200 body lift is moving the radiator and fan out of alignment causing the engine to overheat and head gasket failure especially if the bottom half of the radiator fan shroud is removed thereby preventing the engine from cooling properly. Making some major modifications to the radiator brackets to try and overcome this issue would not be easy.
Sometimes I pushed it very hard, but to avoid any damage I also used the AC fan as a switchable extra cooling fan. As the temperature start to rise I turned on the AC fan (there was a DIY switch to do that ) and reduced the temperature back to normal level. Also added into the waterline a digital thermometer to check the exact value. Never had any issue.
hello I bought a 50mm body lift kit. do you need to change something to the car, add any pipes or brake pipes?
50mm is on the limit in some cases over the limit. During the build you will see that in your case is it enough to loosen up the brake lines or you need new ones. Botom part of the cooling fan deflector cover must be taken of. Intercooler is on the chassis, there the hoses could be short.
I've took the main bolts for the lift out and tryed raising it but it won't lift is there any other bolts do I need to take out the ones around the shifter or the side steps off done the rear fine
No, there's only 4 bolts on each side. You need to loosen one side at a time and you're good. 3 bolts in the cabibe, 1 bolt front of the front wheel.
Hello my Friend i need yoor opinion ,I have problem with Batery ,What do you do?Thanks my Friend
I need longer Sirmata
Hello, please i have question. Did i need a modification in the transfer lever i do only 1" body lift?
Thanks s lot , continue doing that, you are a genius 🙏
There's also 1 inch in this video. So, yes, it's highly proposed to modify the levers.
Hello. If you dont mind me asking, whats the diameter of those plastic spacers you used for bodylift? Thanks.
Hello! They are 50 mm. You can use 60 mm also.
@@AdditionalLosses thanks!
Nagyon dögös lett!
Szia! 3cm body kit. 3cm futómű emelésel elforog szépen a 285/75r16 kaiman mintás terepgumi? Válaszod köszönöm.
Szia! Gyári felnivel igen. Kisebb ET-jű felnivel, vagy nyomtáv pogácsával már egy kis alakítást igényel a sárvédődob, de aki be tud tenni egy ilyen emelést, az meg tudja azt is csinálni, mert csak kb 5mm hiányzik az első kerekek mögött. Egy kis flex és kalapács kell neki, hegeszteni nem kell semmit.
Hello it's me again. Can you tell me the length of bolts I'll need if am doing a 2 inch bodylift?
Hello! At 2:55 you find the answer. (english sub is available). Originally the 4 pcs/side under the cabine are M10x100mm, under the ber 3pcs/side are M12x50mm. So you need 8 pcs M10x150mm and 6pcs M12x100mm bolts.
@@AdditionalLosses Thank you so much. Continue making videos like cv boots change. Oil changes etc. You can't imagine how simple stuffs people wanna see.
@@yuvvraajbeinghuman4730 Thanks for the tips. I will use them.
hello, do you have the original cilinder head on your mitsubishi l200 ??
I'm not the first owner of this car, but as I know yes, this is the original one. It was not yet boiled. :-)
@@AdditionalLosses you are a lucky one :) i need to buy a new one.
@@alinlow Yeah, I know a lot of guys fighting with the same problem. This is a potential failure of the 4D56. I take care of the cooling system, the radiator is cleaned the ventialtor clutch and the water pump is brand new, and - because I push it hard sometimes - to tell you the truth, I converted the A/C ventilator to an extra cooling electric fan as I put it onto a switch which I can control from the cabine. In hard cases I turn it on to have extra cooling. After the repair I recommend you to do the same.
@@AdditionalLosses Hey how can i find if i have the same problem with the head ?
@@ilialulov4447 Sorry, what exactly is your question?
Hello did you put extended brake hose?thanks
Hello, it's not necessary. Just need to loosen it from the retaining tab in the fender.
Ok Is it no problem with 2” body lift how about in gear stick ?cheers
@@byahenglondon5165 Gear levers mod in the part 2 of the body lift video.
ruclips.net/video/BqQh-lvdbp8/видео.html
Üdv
Két kérdésem lenne:
A pogácsák külső átmérőjét meg tudnád adni?
Ezek POM rúdból lettek darabolva?
Szia! 50mm, de jó a 60mm-es is. Ezek fekete danamid rúdból lettek darabolva.
@@AdditionalLosses Szuper!
Köszönöm!
@@Alberstein100 Szivesen! Jó munkát!
A kormány rudazatát nem zavarta a bódé emelése?
Nem. Emlékeim szerint az elbìrná az 5cm emelést is.
@@AdditionalLosses Értem köszönöm. Van csukló a kormányoszlopban?
@@egyigazinagylacc Sajnos nem emlékszem pontosan. De igen, mintha a kormánygép felett lenne. Oldalról, a sárvédő felől látni kellene.
Szia!
Mi értelme van ennek a pogácsás emelésnek?
Ha nagy kerék van az autó alatt, akkor kevesebbet kell faragni, hogy elférjen.
Additional Losses , a rúgókkal nem lehet emelni?
@@qunotrack856 A torzióst egy szintnél jobban nem lehet megfeszíteni, kemény lesz az eleje, illetve a lengőkar akkor az ütköző bakjáig lent lesz és a féltengelyek sem szeretik azt a szöget.