It is because of the board , if you are using node mcu it has a separate pin configuration , if generic 8266 it consist of specific pin config. See the config of your board on the net and then change the D5 pin name.
Yes , I too faced the problem Actually this project has many bugs , I changed the relay circuit in default on portion. After I completed all these setups , this project sometimes works ,and sometimes not I faced many difficulties around this .
@@HowtoElectronics Hi, I am wondering How you were able to fit all those components on that PCB. I am attempting this project and have ordered the PCB but I am not sure how to arainge the Display and the Relay so that they both fit. Do you have a photo or a video of the fully assembled PCB with all components soldered onto it that you could share? Very cool!
Who's this new girl. Her voice is so cute and thanks for letting her in, in your videos 🥰😍
I did it but motor is not switching off.
Same here
Hello did you clear the issue? Can you please tell
Same here
What is your implementation cost?
can u please tell us about the machine learning model you implemented .. it will be very helpful for us
What should i do when relay module and motor does not work?
Airvalue and watervalue replace with value 1 & value2 what is the value for value 1 &2?
From the circuit diagram presented at time 03:18, where is the submersible water pump connected to????
Lol
Nice video, but i am getting NAN values on the old screen for the Temp and Humidity please help
Kindly make a video to control a three phase water motor so this can be really applied in irrigation system
Why is the motor still running when the ground sensor is plugged in to the water and the RH is always 100% please help me
@Ataur Rahman I found a solution to this problem :)
Motor just keeps running
Can you please tell how did you clear the issue?
Hi As per the architecture i have connected everything but at the end the water pump is not turning off and its in always on state
Which editor do you use in this project to run the program
Arduino ide
Nice project with good explanation.
Sister i know your aim is not money
And i prey for you for got many views and subs👍
Overall implementation cost?
I calibrate the soil moisture and everything, but the pump is still on, and it doesn't turn off when it has 100% water.
Can we add rain sensor in this project ?
does it use fuzzy logic?
The ESP8266 ADC takes a max of 1.2V, I believe. The capacitive sensor goes to 3.3V in its output. Did you need to compensate for that?
Most ESP8266 development boards come with an internal voltage divider, so the input range is 0 to 3.3V.
I have a YL69 also it works?
Hi could u please help me i'm getting error in coding part as error in redefination of unit8_t splash data[ ] ....
How could I over come this
Very clear explanation. Thanks a lot. This will be my final year poject.
Hey.. Even I'm planning to work on the same project..Are the code and the circuit diagram given in the description is correct??
Yeah ur review is also helpful for me
Hello.. Did any of you go along with doing this project??
@@mashapimatimba8063 hey I need a help..that is I want to know..where did the coding is edited..in this project..can you plss say me that..!!
Hi can you add more than one sensor ?? i have a project to irrigate my vegetables on my balcony im living in a city:)
How much cost ?
This circuit is for 1 plant
Can you upgrade to this circuit for 4 or mor plant monitor
Plz make a video
Who is this new girl. She really has a very sweet voice.I've never heard such a great voice.Really i love her voice..!!❤
Hi bro, thanks for the compliment. She is new member of "How To Electronics" Team.
Ooohh..that's great...!!❤
For controlling the water pump we just need relay and a digital pin right ?
Yes and you can use Blink app
How describe my teacher when ask a question this system?
in thingspeak field 4 (motor status), how do you set the condition of motor status?
If digital pin that is connected to motor is high, then 1 is sent to thingspeak, if its low, then 0 is sent.
@@HowtoElectronics but it will not respond sometimes
hello, nice work. Am doing this a my school end of year project, but I have problem with the code, please can you help me with the code?
Even i Inserted Soil moisture into water ,Motor is still running???
Same problem
@@kunalvatwani9535 we finished this project its working 100% crt
How did you fix it?
Would be a great help if you could help
@@kunalvatwani9535 first connect as per circuit diagram
Wohhhh wonderful
!!
Keep up the great work. looking forward to your future videos.
Thank you so much 🤗
hey I keep getting 'WiFi' was not declared in this scope.. could you tell me where you got the library for the node mcu?
try downloading the correct libraries of node Mcu to access the wifi functionality
Can I use lcd 1602 inplace of oled screen
ooh yes but you need to write code for this
Sir.
Can you show us about water quality device like Ph value, oxygen level, ammonia level, water temperature.
Thanks
I am currently working on this device. It will take month to build abd test.
Will it still work if you use other version of node mcu?
Yes it will
Can u make video about design pcb
Hello Sir Can I get the simulation part of this project on proteus software please.
How many times will you spend for it and typing also (in the website)
GREAT 🙏❤️❤️
GOD BLESS YOU
Hello when you will update and upload the coding ? I can’t wait to try it
Updated: how2electronics.com/iot-smart-agriculture-automatic-irrigation-system-with-esp8266/
I am getting an error "D4 was not declared in this scope" while running the code
same here did u solve it??
@@johanmotha1488 had to change so stuff here and there but still the motor would start but not stop
We can use esp32 ?
Yes..I'm also getting same question ?
use python?
Nice one
Is the source code for module esp8266 wifi need to change when using esp32?
Yeses
How to change the code?
Which program language is used in source code?
C/C++
Wonderful demonstration. Thanks for the video. Helped a lot
Glad it helped!
Hey did you do the project?? Are the code and the circuit diagram proper?
what is the importance of measuring temperature and humidity sensor?
Its very for measuring Air Temperature and humidity. The external environmental factor is essential for crop production.
I did a serial communication to send data from arduino to esp8266 ..now i want to send that data from esp8266 to blynk .does anyone have an idea ?
Please use lora module in this
Did you understand how to use ?
There was an error as D4 and D5 pins are not defined..
i am also got same .What to do?? Please reply.............
It is because of the board , if you are using node mcu it has a separate pin configuration , if generic 8266 it consist of specific pin config. See the config of your board on the net and then change the D5 pin name.
@@isabarindustries Thanks for your help
@@isabarindustries Even I have put soil Mositure Sensor into Water .The motor is still running Can you help me with this
Yes , I too faced the problem Actually this project has many bugs , I changed the relay circuit in default on portion. After I completed all these setups , this project sometimes works ,and sometimes not I faced many difficulties around this .
Hey..Can u please tell how to make schematic diagram in easyeda..
That will be really helpful
Have you finished this project??
Plz upload the source code
Awesome video bro
V.good project.upload code and files ....
Thanks. It will be uploaded on monday. 🙂
Bro i use also lcd display
Can i call you
Nice video . Can you share you pcb layout file to me
Please wait for 2 days
I will upload and update the link in description with all files. Thank you.
Yeayy thank you , can’t wait to see
@@HowtoElectronics Hi, I am wondering How you were able to fit all those components on that PCB. I am attempting this project and have ordered the PCB but I am not sure how to arainge the Display and the Relay so that they both fit. Do you have a photo or a video of the fully assembled PCB with all components soldered onto it that you could share? Very cool!
how to solve this error(error compiling for board generic esp8266 module) using your code.
Select NodeMCU 1.0 Board from the tools menu not the generic esp8266
@@HowtoElectronics the motor is allways stays on?
aid
Nepali ho ki k ho😂