When I tested the same circuit, the voltage produced by the capacitors became 2 volts. Is this because of the use of many capacitors that reduced the voltage in this way?
Many ek circuit bnaya hai 12 volt ku card wali relay kay sath lakin jab power supply kay sath connect karta hun too voltage 6 voltage par a jatayn hai khali par 12 volt miltay hain please give me salution
Ek 12v 100mamp consumption wali led ko kitne tarike ke source out out se chala sakte hai. 1-12v 100m amp(source max out put) 2-12v 1amp 3-6v 3 amp 4-24v50mamp 5-35v 25 mamp 6-70v 13 mamp 1 & 2 se to shayad chal jayegi.baki aap pls bataye chal payegi ya nahi.
Bro have a question, bhai maine SLA battrey 40ah 12v se led kit chalata hu to sahi jalta hai per use 7x3 Li ion (18600) 11.6v se chalta hu vo fuse ho jati hai kyo?
GREAT bhai, Bhai, 225 j ka five p.f fix kiya, to dc volt same hi raheta , aur mili amp paach guna badjata hai, LEKIN p.f hit hokar fatene ka RIKS to nahi, aur ye circuit long samay ke liye chal sakta hai. Please tell me bhai.
For any Led lighting single resistor is sufficient exact value or more value resistors in seen in indicators. Electronic is not exempted from business manipulation. Extra components in names of safety/protections.
The problem is that this circuit works only for very low fixed current load. If the current drawn by the load changes, then the voltage also changes (in the opposite way. i.e. if current drops, voltage increases). If you want to setup a fixed load (such as LED lamp) which consumes 1 amp at 5v, then the calculation shows that you need a non-electrolytic capacitor of 27.69 Micro Farads (450 V). This spec of capacitor may not be available in market and even if available also will be very costly and buying a regular transformer-based power supply will be much cheaper!!!
OHHHH i see that ''YOU TOUCH'' the circuit with hands.IS THAT SAFE?? OR your project ''CAN BE TOUCHED''?? please PRECISE THIS POINT..or you can harm those watching your video. Thanks
Nehi Mera transformer se koye dushmanhi nahi hai Is video mai humne ea sumghane kosish kiye hai.. Transformerless power supply se v amp bada sakte hai.. Hum is video main 100mA se lekar 500mA tak dekhiya hai.. Jisko jo pasand hai Usi according circuit banay ga
Can i add more capacitors for higher current? I would also have to replace the diode with a higher wattage one. Right?
Yes..
Thanks for the comment 👍😊
@@THEELECTRONICSADDA thank you very much 👍😊
If you put your hand on the DC wire, what will the electric shock?
Thank you for clean and neat explanation.. 👍
When I tested the same circuit, the voltage produced by the capacitors became 2 volts. Is this because of the use of many capacitors that reduced the voltage in this way?
No , the voltage changes depending on the load. if you use two 2.5v LED in series the voltage becomes 5v
you are drawing too much current ... with this configuration .. it can supply around 80ma only
I like this video, pls what is the name if this capacitor and its value thx
Para la entrada de 127v ac sería el mismo sircuito o cambiaria algún componente saludos
Excelente video muchas gracias
thanks
Output filter capacitor discharge korar jonyo parallel ey 10-15 K dile valo hoy na?
Can we run dc 12v fan with this circuit?
Thank you very much for this turtorial. Is there any indicative converter of ceramic capacitor capacity to charging current?
Thanks for the comment 👍❤️❤️😊
Grate video👍
Many ek circuit bnaya hai 12 volt ku card wali relay kay sath lakin jab power supply kay sath connect karta hun too voltage 6 voltage par a jatayn hai khali par 12 volt miltay hain please give me salution
Ek 12v 100mamp consumption wali led ko kitne tarike ke source out out se chala sakte hai.
1-12v 100m amp(source max out put)
2-12v 1amp
3-6v 3 amp
4-24v50mamp
5-35v 25 mamp
6-70v 13 mamp
1 & 2 se to shayad chal jayegi.baki aap pls bataye chal payegi ya nahi.
if not connect the zener diode How many volts will the diode bridge output voltage be? And from this experiment, how can we calculate it to design it?
24v
This is a dangerous circuit and you are teaching people to touch it with bare hands !!
If I want 12V , 2amp power supply then what to do?
Transformer must be used
Agar output me led lights ko serice me na lgatey hue agar parell me lagye tho kya voltage aur current down hoga ....
yes current down hoga
I loved this video and the strait forward circuit design. 😊 A suggestion: add a strong electrocution hazard warning for noobies like me. 😉
Thanks for the comment ❤️👍😊
A tip: you can watch series on flixzone. Me and my gf have been using them for watching a lot of movies recently.
@Caleb Jaxton Yea, been watching on Flixzone for since december myself =)
Bagus sekali mohon ijin saya tuk mbuatnya trimakasih.
Bro have a question, bhai maine SLA battrey 40ah 12v se led kit chalata hu to sahi jalta hai per use 7x3 Li ion (18600) 11.6v se chalta hu vo fuse ho jati hai kyo?
Thanks for the comment 👍❤️❤️
Aap Resistance use kijiye
@@THEELECTRONICSADDA thank you
Sir can we use 1 capacitor ( high value) instead of 2 capacitor
Да. Больше ёмкость - выше ток.
GREAT bhai,
Bhai, 225 j ka five p.f fix kiya, to dc volt same hi raheta , aur mili amp paach guna badjata hai, LEKIN p.f hit hokar fatene ka RIKS to nahi, aur ye circuit long samay ke liye chal sakta hai.
Please tell me bhai.
Koye problem nahi friend
Thank you so much for the comment 👍👍😊😊❤️
@@THEELECTRONICSADDA thanks bhai,
For any Led lighting single resistor is sufficient exact value or more value resistors in seen in indicators. Electronic is not exempted from business manipulation. Extra components in names of safety/protections.
Bro aagar hum 10 pf capasitor ko paller. Me connect kare 104 j 400 v ko to kya a 10 ampire Outpt dega
No
if i want 5v1.0amp as my output from 220vac which cap should i use?
The problem is that this circuit works only for very low fixed current load. If the current drawn by the load changes, then the voltage also changes (in the opposite way. i.e. if current drops, voltage increases). If you want to setup a fixed load (such as LED lamp) which consumes 1 amp at 5v, then the calculation shows that you need a non-electrolytic capacitor of 27.69 Micro Farads (450 V). This spec of capacitor may not be available in market and even if available also will be very costly and buying a regular transformer-based power supply will be much cheaper!!!
Good experiment👍
Thank you 🤗
Thanks. 😷👍🇬🇧
You are most welcome☺️☺️❤️👍
Kaya isse amplifier chala sakte hai because esa same mene banya tha per vo kam nahi ker raha hai
Dude can you able to make 500ma to 3amp circuit?
How many volts is that input voltage?
230V AC
If i want 10A of current, i need 100 capacitor?
Yes, but it is not the right method
@@THEELECTRONICSADDA i know, just joking :v. Or maybe can i use 10 12v 1A wall adaptor to get 10A or 5 adaptor of it's 2A yet?
@@diablodizzy. theoretically yes, practically no due to the ripples.
Good
Thank you so much my friend
Sir This Supply Voltage?
12V
good
Thank you so much for the comment
What is the wattage of the resistors you use?
1M,1K - Quarter Watt
Please try to made a power bank circut with mc34063 ic
Ok
Thank you so much for the comment 👍❤️❤️😊
Sir can we make 12V 1A power supply like this
Opp Bhai oppp Bhai opppp 👍👍👍👍👍😘😘😘😘
Ro ki motar ke lie bhi
I will try
Sir very good !
Thank you so much my friend 😊❤️👍
Sir. Can this capacitor be 250V?
Thank you very much
@@valdomirosilva4127 400V Capacitor
Shock(crunt) nahi lgta ???
Bhai 155j 400v capacitor (single) kitna ma output dega ?
100 ma
Hello Can I Charge 800 Mah Battery With That Circuit Reply Me
Yes.
Thanks for the comment 👍😀😀❤️
sk gaming this circuit output is 500ma and you use 800 ma battery so you can use only 2 capacitor 200ma suply.and charge the battery.
What can happen if the 1 mohm
resistor was changed to 500 kilo
ohm resistor?.
whats the zenor diode wattage..?
Can we add more pf
Thanks bro
Bhai Esme hath laga rahe ho ..... Current nahi lagta kya
How do you say Current values
you measure only voltage
Very useful information bro
If zenor diode is 1W and voltage is 12V then max current it can handle max .83A otherwise diode will get blast
Yes
Use 7812 with heat sink
Super
Thank you so much for the comment ❤️❤️☺️👍👍
👍🏻👍🏻👍🏻
Thanks 👍❤️😊
How to make Transformerles 12v 5 ampere ?
The output ampere is 500ma but what if I want 12 v 2 ampere... Which parts I need to change.. To increase ampere
Not possible
Supar video
Thank you so much for the comment ❤️❤️👍
Sr is srcit se 12 voltas 12 ampere charger bnakr dikhaye
No
@@THEELECTRONICSADDA3 ampere ka bna sakte hai kya
No
Why didn't you tested the current using the Multimeter?
I'm sorry
I didn't have an ampere meter then
I meant the Multimeter u are using this video . You could have measured the amps with that
@@THEELECTRONICSADDA you can measure in the dc ampere range of the multimeter with a resistor in series.
Wow😯😯😯😯😯
Thanks 👍❤️
Without diode.what is BD107 bridge rectifier
This is not BD107
Will be DB107
Thanks 👍❤️😊
Please make 5v 500ma.
Led bulb pey 100 v dc per pf konsa lagya
Aap konsa led bulb lagana chate hain
Itu pake diode ?
Main kich samjha nahi...
V good. Sir mere pas 150wat ki led light hai. Input currant mppcb 1000-2000 mamp and dc volt 42-54 hai. Pls circuit details.
mere pass iska circuit details nehi hain
1m ohm 1/4 watt nile hobe
Hmm hobe
Thanks for the comment 👍😊😊❤️
что нужно чтобы подключить 100 шт./лот, 3 Вт, 45 мил, 380нм-840 нм, 3,2-3,6 В, 700 мА, полный спектр, подскажите пожалуйста
what zener type, also the ampere of zener
12volt 1 watt
Thanks for the comment ❤️😊😊
What is the mah output.?
500 milliampere
This Supply soldering system video link.send me this video speed sir
check circuit diagram
I need 56 v
How can regulateto 56
Can you do 48v 10amp Adjustable ac to dc
Yes i can
5 volt 2 amp power supply kaise banaye sir ?
100 pf 400v ka kya use hai
Bhai koi aur capacitor batao Jo 100ma current output de
you can use 474K - 400V Capacitor
Sir aapne 5 pf laga diye 50/- ke to pf ho gaye Jabki 50/- mai to 12 v 2 amp ka adopter aa gayega
Joy of creating something will not come then
100mA means . 1 amp... Ami 2amp chai thle ki korte hbe
100mA = 100 mili amp
2 amp power supply er jonno
12v 2 amp transformer diye banate hobe
Transformer chara korte chai.... Kora jabe????
Na
ट्रांसफार्मर जैसी पावर कैसे निकलेंगे
775 dc motar ke lie bnao
I will try
Nobody and nowhere making video about 2amp 6v dc transformerless. Can u tell me that will u able to dare to do that ?
6 volt 2 amper transformerless power supply cannot be made
Thank you so much for the comment 👍👍😊😊❤️❤️
Sir 12v supply cricut video link send me
Follow the circuit diagram given in the Description
I don't think so, zener diode will burn if yiu add more capacitors.
At least mine died
Use 7812 with heat sink
OHHHH i see that ''YOU TOUCH'' the circuit with hands.IS THAT SAFE??
OR your project ''CAN BE TOUCHED''??
please PRECISE THIS POINT..or you can harm those watching your video.
Thanks
It is dangerous for people's do not understand electricity
Yes
It should be DB107
You can use 155j 400v for 100mA, why use 225j 400v
155=1.5 MFD,225=2.2 MFD, means more capacitance
Please give some more information about.
Okkkkkkk
👍👍☺️❤️
This is not the proper way to teach.
High amps only 5Ma?😑
bait cover
transformer se kya dushmanhi h tumhe.. itnse kamsize or kam kharche 300mah ka transformer hi aa jata.
Nehi
Mera transformer se koye dushmanhi nahi hai
Is video mai humne ea sumghane kosish kiye hai..
Transformerless power supply se v amp bada sakte hai..
Hum is video main 100mA se lekar 500mA tak dekhiya hai..
Jisko jo pasand hai
Usi according circuit banay ga
@@THEELECTRONICSADDA bhai ye highly unstable hota h. U sud not promote this. 25rs me smps aa jata h itne power ka.
@@MMaheshThakur sahi kaha current thoda high milta he par... efficiency bohot kharab hoti he smps k mukable. Isilye ye itna kam ka nahi ..use k liye
This Supply soldering system video link.send me this video speed sir
Follow the circuit diagram given in the Description