Not really! The red and black wires are for a continuous power supply incase your head unit allows you to view camera while not in reverse! If it doesn't, you don't even need to connect that pigtail! All you need is the video plug and to run that single wire to the reverse light posative!
Hi, I have a camera already installed and connected to 12v in the reverse light. But there is no red small cable in the video connector. It is possible to connect this camera to Android unit with canbus? Thanks
john coburn basically find positive from the back of the radio and the ground. Connect them to the camera power. Connect the camera plugs and that is it
Thank you . Seriously.... I've watched multiple videos on install reversing cameras . They either started off saying one thing and changed half way through or the relative of the village idiot came on . Watched yours clear easy simple instructions. Had it installed within minutes
Even i didn't complete i .. I understood the concept very fast and apply it on my car and it work perfectly .. Thanks for the good brief ... Good video
Got my backup camera working finally in my 2010 tacoma. the factory one didn't work with the pioneer nex 1400 stereo. I bought a $15 cam from walmart & it still didn't work. I bought another $15 cam today from walmart & this one worked !
I’m pretty sure the C6 never had a backup camera across any spec for the generation, so it would be impossible to install a factory backup camera that never existed. And if you meant to factory radio it doesn’t got the input connections for it sense they never had a back up camera for the generation.
I’ve recently followed your video I have a canbus box on my caddy but camera wouldn’t trigger any ideas? Camera leds wouldn’t light up so I’m guessing no power but the reverse on the head unit was working fine just no signal to the camera
Ok I have a Kenwood DDX model with the camera button so I need to run separate purple wire from the reverse trigger wire? And then the red wire from the camera connects to the red from wire harness? And of course need to tap into the ground wire.
The RCA female and red power female plug started off the same point , but the RCA red wire is much shorter than the power red-black wire , so how does the 3 touch together ? Extend the RCA red wire ? Or splice into the beginning of red-black power wire to connect the RCA red wire , then splice again at the end into the reverse light power.
The RED wire that is along with your yellow to your devise I split in the middle and from there I connected the other one kind of like a "T" if you understand I hope you do you'll get it
I have a stock toyota corolla touch screen deck. I dont have the yellow rca plug behind my deck to connect but i see other ppl able to install camera anyways. Is there some type of adpater for my stereo? Please lmk
I bought the 07 to 14 Tahoe Phoenix automotive radio. The only wire that I can hook to is a blue wire for an amp and a brown wire for a break. Do I hook it to the brake wire
@@caligaming9386 That’s if you want the LED’s on the camera to burn ALL OF THE TIME. The red plug at the camera is only to power the LED’s. The camera itself gets power from the yellow plug at the radio. This is why the “convenience wire” was added later. So you could view the camera (if radio has the option inside of it ) without the LED’s burning all of the time . When you tie in the “convenience wire at the tail light “? That just signals the radio to show the view without hitting the button in the radio . And turns it on when hitting reverse. This is NEVER explained in videos. The RED AND BLACK ON THE PLUG AT THE TAILLIGHT “? It’s only powering the LED’s in the camera. The camera gets power (because it also has a positive & negative ran inside of a single plug ) from the yellow plug at the radio/head piece. Explaining this would take all of the complexity out of it.
Hi, I have a camera already installed and connected to 12v in the reverse light. But there is no red small cable in the video connector. It is possible to connect this camera to Android unit with canbus? Thanks
Hello, i have followed the instructions on your video and did exactly the same on my Nissan Qassqai but the screen is not showing the reverse camera on my CONNECT GET 1 head unit., i have some pictures that i want to share with you to get your suggestions as to where i am going wrong. it will be a great help if you can advise
Now for us complete novices who’ve never done something like this but want to, can you make another video actually going through each step? Also, walk through the connections for setting up the camera to be used as a front camera.
So on my aftermarket radio it came with a camera but none of the spots on the harness has a spot for it. What else would I be able to hook it up to for the power? Can I hook it up to a accessory (key on power) on the harness ao when I turn the key on it turns on the camera.
Can you advise what the reverse trigger wire is? My unit doesn't bring up my camera. Truck wasn't factory wired for one so no stock reverse wire. I have my reverse positive wire tapped just need to know what to tap on the headunit. 13.6 px6 tundra 2010
Kyle Bechtold I talked about this. How to install a Backup Camera Any Toyota Camry 2012-2013-2014 - Step by Step (Problems are Fixed) You don’t need trigger from rear light
I know your post is about 5 months old, however, when hooking up this camera, the Reverse Trigger wire is the power wire running to you reverse light in your tail lights. This is the white reverse lights not the red break lights or the yellow turn signals.. So when you put your car in reverse, the white lights shine so you can see when backing up. You will need to tap into the wire that runs to that bulb For most of my cars it is a green power wire and a black ground wire. That will send a signal to your camera when you put it in reverse.
Hello Can you advise if the black is always going to be ground and red power? i am trying to connect the camera to a kia forte 2015 brake light and there is a black red and green wire Thanks in advance
I connected everything as per the video as I connected the red "power" wire to the "back up" lights. I did that, because the "back up" lights only get power when the car is put into "reverse." Since I only want my rear view camera to work when my car is in "reverse," I thought that this is the logical way to do it. Well, I am getting a "No Video Signal" message on a black screen! Any advice?
Hi, I have a camera already installed and connected to 12v in the reverse light. But there is no red small cable in the video connector. It is possible to connect this camera to Android unit with canbus? Thanks
Alyana Beltejar yeah i just got done with the install a couple days ago following this vid, only thing is the Line out put converter he linked different than one in the vid so I ended up using the PAC LP5-4
How can I get my front camera working ? I got the reverse cam working but can’t figure out how to get the front cam working . Not sure where to connect the red wire behind the head unit . I connect it with the reverse one , it turned on but I cannot view (and it has its own rca front cam)
I bought a px6 for my 2006 lexus is 250 I has the navigation system and back up camera so I want to keep my OEM back up camera can you tell me how can I do that
This is correct except were it plugs into the stereo. In back of the 13.3 androide it plugs into the ccd-2 and the trigger is on the same plug with the wifi cable.
The small wire from the reverse light is just to power the LED lights on the camera. The RCA wire has both power and signal for the camera. The reverse triggering is done from the front radio end and has nothing to do with LED lights on the camera. The camera should work fine during daylight without the LED lights.
Why is the red wire coming off that yellow RCA so short on the back end if it needs to go all the way to the reverse light? The power wire that's ajoined to the ground wire is nice and long, why is the other one not? They could have give us at least one meter...
See that's what I thought I've hooked up back up cameras plenty of times before I got the RCA running with the red wire in it for the trigger and then I got the camera running off the other reverse light so I'm not drawing too much off the one cuz off the one it didn't want to work so I did it off the other one and just with the ground wire hooked up and the power wire unhooked just for the camera it was still trigger the radio to pop up the screen for the backup camera but if I hook up the ground for the camera it puts my amp into protect and it takes away the backup screen and then dims my backup lights how is that possible with just the ground wire hooked up for the camera and only the trigger wire hooked up for the radio soon as I plug that RCA in to the camera it does what it does and puts my amp into protect dims my lights and kicks the radio out of reverse
I installed a side camera and enabled the settings to show when right turn signal is activated but it doesn’t work. Do I need to get the camera power from the turn signal? If so will the camera turn on and off with the fluctuating signal light?
Hi Thanks for your videos, very helpful. I bought this item and I fixed it. When I switch the reverse gear everything works fine but when I switch on (start engine) it shows two displays in the monitor, I mean two pictures running at same time in one monitor. Can you show a diagram how to fix this item please? Thanks. This is the item I am talking about: 360 Degree Bird View System 5" Monitor Auto Car Recording 4 Camera Panoramic | eBay
whenI put it in reverse the camera doesn't come on unless I go to my radio and and tap on camera how do I get it to come on when I put the gear in reverse?
Hello. I have installed this xamera on my car and it worked fine for some time but now it is operating very slowly, basically lagging be it in selecting the menu options or the camera it self. Any idea why this could happen and how to fix it?
Holy shit this simple video was much better than all those complicated tutorials, thank you so much
FINALLY a clear explanation of where the wires connect to. Thank you!
Not really! The red and black wires are for a continuous power supply incase your head unit allows you to view camera while not in reverse! If it doesn't, you don't even need to connect that pigtail! All you need is the video plug and to run that single wire to the reverse light posative!
@@nutsackbear8053 If you use canbus decoder, no need to conect on the reverse light positive.
Hi, I have a camera already installed and connected to 12v in the reverse light. But there is no red small cable in the video connector. It is possible to connect this camera to Android unit with canbus? Thanks
Great video and easy to understand. I like that you didn't un-twist all the wiring and intertwined while explaining it so it made it easy to follow.
Am I the only one who watch this five time and yet couldn’t understand anything 😅
Thanks for this. Simply put. Every other video just made things so much more confusing than it needed to be.
john coburn basically find positive from the back of the radio and the ground. Connect them to the camera power. Connect the camera plugs and that is it
john coburn How to install a Backup Camera Any Toyota Camry 2012-2013-2014 - Step by Step (Problems are Fixed)
Thank you . Seriously.... I've watched multiple videos on install reversing cameras . They either started off saying one thing and changed half way through or the relative of the village idiot came on . Watched yours clear easy simple instructions. Had it installed within minutes
This is one of the nicest videos I've ever seen. Very clear that mine installed the same day. Thank you for the video
Straight to the point! Wish more videos on youtube were this simple. No silly music or "like, subscribe" bs. Thanks!
Thanks for making it clear and easy to understand I watched 4 different videos and didn’t understand a thing
Best break down video thank you !
Even i didn't complete i .. I understood the concept very fast and apply it on my car and it work perfectly .. Thanks for the good brief ... Good video
Thank you mate, I have the exact camera and the instructions are shocking..
This explains perfectly.
The red convience wire makes so much more sense now. Thank you so much
I’ve watched so many of these videos and out of all of them this is the one 🏆
Great video. First that actually made sense
Best Video Ever 👍👍 👍 thank you
Good video. Keep making straight to the point videos. 👍🏿
Got my backup camera working finally in my 2010 tacoma. the factory one didn't work with the pioneer nex 1400 stereo. I bought a $15 cam from walmart & it still didn't work. I bought another $15 cam today from walmart & this one worked !
very easy explain method. you fit to be teacher, thanks sir.
Amazing video ! To the point !
Very straight fwd other videos u still scratch your grey hair on your head but this is on point .
Thank u simple n straight to the point
You made it look very easy sir. I appreciate it. Thank you very much. I’m gonna try it and if my car explodes, I’ll let you know. Lol 😂😅
Very good and short explanation Thanks
Reverse signal feed goes to pin 1 on iso plug. Had trouble finding that anywhere
Very helpful and clear. Thank you!
What if you just need to hook it up to the factory back up camera?
yu’re on the wrong video, says aftermarket, not factory
I’m pretty sure the C6 never had a backup camera across any spec for the generation, so it would be impossible to install a factory backup camera that never existed. And if you meant to factory radio it doesn’t got the input connections for it sense they never had a back up camera for the generation.
best video out there. So so simple.
Thank you so much, I was just about to burn the whole lot😂
I want a front setup. How do I hook that up for a grill mounted camera? What are my connections? I want to see in on my in-car display
Great video guide! Greatly appreciate this one! This install was killing me until I found this!
What if you are doing a front camera and don't need a reverse power wire?
I’ve recently followed your video I have a canbus box on my caddy but camera wouldn’t trigger any ideas? Camera leds wouldn’t light up so I’m guessing no power but the reverse on the head unit was working fine just no signal to the camera
Ok I have a Kenwood DDX model with the camera button so I need to run separate purple wire from the reverse trigger wire? And then the red wire from the camera connects to the red from wire harness? And of course need to tap into the ground wire.
What color is the single wire going to be at the radio side to connect the backup camera? The one that is attached to the RCA plug.
Good clear and understandable video, many thanks
What if you have a camera already, can you not just switch out the camera it self? Or is their usually different connections?
I was able to use the factory backup camera on my car
The RCA female and red power female plug started off the same point , but the RCA red wire is much shorter than the power red-black wire , so how does the 3 touch together ?
Extend the RCA red wire ? Or splice into the beginning of red-black power wire to connect the RCA red wire , then splice again at the end into the reverse light power.
The RED wire that is along with your yellow to your devise I split in the middle and from there I connected the other one kind of like a "T" if you understand I hope you do you'll get it
I have a stock toyota corolla touch screen deck. I dont have the yellow rca plug behind my deck to connect but i see other ppl able to install camera anyways. Is there some type of adpater for my stereo? Please lmk
thanks for making this video so simple thats all i needed
Glad it helped!
Thank you very much for your video. The manual of my camera doesn't even mention the red wire attached to the yellow male to male video cable.
Hello friend, thanks for the video. I only have one question please, where can I connect the ground black cable ? Thank you very much 😊
Great explanation
I’ve wired like this but camera does not turn on and I have no video signal to the head unit. Is there a way to test the camera with a multi meter?
I bought the 07 to 14 Tahoe Phoenix automotive radio. The only wire that I can hook to is a blue wire for an amp and a brown wire for a break. Do I hook it to the brake wire
Plus didn’t know if there a setting to change
Does this work with an rcd 330 and if I need other connections or anything can you please assist 🙏
Great video! What if you want the camera to stay on while you drive , like a rearview mirror ?
You have to connect the power source to somewhere other than the rear brake light.
@@caligaming9386 That’s if you want the LED’s on the camera to burn ALL OF THE TIME.
The red plug at the camera is only to power the LED’s. The camera itself gets power from the yellow plug at the radio. This is why the “convenience wire” was added later. So you could view the camera (if radio has the option inside of it ) without the LED’s burning all of the time .
When you tie in the “convenience wire at the tail light “? That just signals the radio to show the view without hitting the button in the radio . And turns it on when hitting reverse.
This is NEVER explained in videos.
The RED AND BLACK ON THE PLUG AT THE TAILLIGHT “? It’s only powering the LED’s in the camera. The camera gets power (because it also has a positive & negative ran inside of a single plug ) from the yellow plug at the radio/head piece.
Explaining this would take all of the complexity out of it.
Hi, I have a camera already installed and connected to 12v in the reverse light. But there is no red small cable in the video connector. It is possible to connect this camera to Android unit with canbus? Thanks
Thanks 👍 very straight forward.
I messed up my alternator and battery trying to install and final got it right after watching this
Does the single wire need to be 12v all the time or when in reverse only?
This is an awesome demonstration
Thanks.
Hello, i have followed the instructions on your video and did exactly the same on my Nissan Qassqai but the screen is not showing the reverse camera on my CONNECT GET 1 head unit., i have some pictures that i want to share with you to get your suggestions as to where i am going wrong. it will be a great help if you can advise
You said the black wire connects to the reverse back light?
Very useful it helps me very well ,thanks u sir I just like an d subscribe to ur channel
Now for us complete novices who’ve never done something like this but want to, can you make another video actually going through each step? Also, walk through the connections for setting up the camera to be used as a front camera.
So on my aftermarket radio it came with a camera but none of the spots on the harness has a spot for it. What else would I be able to hook it up to for the power? Can I hook it up to a accessory (key on power) on the harness ao when I turn the key on it turns on the camera.
Can you advise what the reverse trigger wire is? My unit doesn't bring up my camera. Truck wasn't factory wired for one so no stock reverse wire. I have my reverse positive wire tapped just need to know what to tap on the headunit.
13.6 px6 tundra 2010
The wires are labled.
Kyle Bechtold I talked about this. How to install a Backup Camera Any Toyota Camry 2012-2013-2014 - Step by Step (Problems are Fixed)
You don’t need trigger from rear light
I know your post is about 5 months old, however, when hooking up this camera, the Reverse Trigger wire is the power wire running to you reverse light in your tail lights. This is the white reverse lights not the red break lights or the yellow turn signals.. So when you put your car in reverse, the white lights shine so you can see when backing up. You will need to tap into the wire that runs to that bulb For most of my cars it is a green power wire and a black ground wire. That will send a signal to your camera when you put it in reverse.
if you habe can bus , do you need the red cable to the unit? and how you cand find if you have can bus?
So no need to tap in to the reverse tail light?
Correct
Could the "reverse" wire coming out of the stereo be shorted?
Great video bro.. buen video bro
when i hook up to tesla style for 2009 lexus rx350 i get black and white and like 6 split screen on monitor ? can you please help?
Best explaination
I added a secondary camera, a front camera but the image is inverted. I know I can flip the backup camera but can I flip the front camera?
Hi, is thisa the same for a can bus system. ?? Thanks
great video thanks for the help
1:37 “black wire goes to ground”
What Ground? More specification please
The location of grounding points varies depending what vehicle you're talking about.
Hey bro, does this connect to any car camera or do you have to buy the camera separate?
how do you override if want the rear camera to come on while driving forward ???/
Hello
Can you advise if the black is always going to be ground and red power? i am trying to connect the camera to a kia forte 2015 brake light and there is a black red and green wire
Thanks in advance
Can you do a video on adding a front camera?
Johnpatrick Murphy just connect to front cam rca port. Others are same
How many blown stereos caus it's about to add 1 more
I connected everything as per the video as I connected the red "power" wire to the "back up" lights. I did that, because the "back up" lights only get power when the car is put into "reverse." Since I only want my rear view camera to work when my car is in "reverse," I thought that this is the logical way to do it. Well, I am getting a "No Video Signal" message on a black screen! Any advice?
Whata a good backup camera license plate style
Hi, I have a camera already installed and connected to 12v in the reverse light. But there is no red small cable in the video connector. It is possible to connect this camera to Android unit with canbus? Thanks
Hey can you please explain camera wiring for front camera. Thanks
Will wiring it this way allow my camera to turn on when in reverse and when I’m driving and select the reverse camera option on my double din?
Did u figure it out
Alyana Beltejar yeah i just got done with the install a couple days ago following this vid, only thing is the Line out put converter he linked different than one in the vid so I ended up using the PAC LP5-4
HELP! how to connect the 3 cables? to the back of the headunit, since the red cable of the 2 rca males doesnt reach the back of headunit?
While we cut reverse light wire to connect camara red wire. Does warranty voids?
How can I get my front camera working ? I got the reverse cam working but can’t figure out how to get the front cam working . Not sure where to connect the red wire behind the head unit . I connect it with the reverse one , it turned on but I cannot view (and it has its own rca front cam)
Nice video thanks
my unit doesnt mention anything reverse related, and only loose wires are brake and amp control
I bought a px6 for my 2006 lexus is 250 I has the navigation system and back up camera so I want to keep my OEM back up camera can you tell me how can I do that
You need to do some wire cutting and splicing.
@@phoenixautomotive4336 can a Phoenix person come did the wiring and cutting?
@@pod0004 You can come to our location.
@@phoenixautomotive4336 in California? I'm in Texas.
@@pod0004 Yes, we are located in LA.
Me after watching this video: thank you, a front camera will be enough for me
How can I make my oem camera 2015 Tahoe work no picture or harness to connect or did I miss something out Thanks
This is correct except were it plugs into the stereo. In back of the 13.3 androide it plugs into the ccd-2 and the trigger is on the same plug with the wifi cable.
Why would you need power feed to camera from TWO cables;
one cable from head unit through video feed,
and another cable from reverse light positive?
The small wire from the reverse light is just to power the LED lights on the camera. The RCA wire has both power and signal for the camera. The reverse triggering is done from the front radio end and has nothing to do with LED lights on the camera. The camera should work fine during daylight without the LED lights.
Does the black ground wire connect to the black wire that goes into the reverse light or just ground it to the metal somewhere?
Either way works
Hi I do not have video input cable in my navigation, what to do ?
Why is the red wire coming off that yellow RCA so short on the back end if it needs to go all the way to the reverse light? The power wire that's ajoined to the ground wire is nice and long, why is the other one not? They could have give us at least one meter...
Simple👍👍
can you tell me how to hook up for front view PAF8451?
wanna install front camera were do i tap into power so its not on all the time
2018 chevy silverado 2500 hd
What about the ground wire where i can connect?
See that's what I thought I've hooked up back up cameras plenty of times before I got the RCA running with the red wire in it for the trigger and then I got the camera running off the other reverse light so I'm not drawing too much off the one cuz off the one it didn't want to work so I did it off the other one and just with the ground wire hooked up and the power wire unhooked just for the camera it was still trigger the radio to pop up the screen for the backup camera but if I hook up the ground for the camera it puts my amp into protect and it takes away the backup screen and then dims my backup lights how is that possible with just the ground wire hooked up for the camera and only the trigger wire hooked up for the radio soon as I plug that RCA in to the camera it does what it does and puts my amp into protect dims my lights and kicks the radio out of reverse
Good video
If you use the reverse power you dont need a trigger at the head unit.
I installed a side camera and enabled the settings to show when right turn signal is activated but it doesn’t work. Do I need to get the camera power from the turn signal? If so will the camera turn on and off with the fluctuating signal light?
Hi Thanks for your videos, very helpful. I bought this item and I fixed it. When I switch the reverse gear everything works fine but when I switch on (start engine) it shows two displays in the monitor, I mean two pictures running at same time in one monitor. Can you show a diagram how to fix this item please? Thanks. This is the item I am talking about: 360 Degree Bird View System 5" Monitor Auto Car Recording 4 Camera Panoramic | eBay
whenI put it in reverse the camera doesn't come on unless I go to my radio and and tap on camera how do I get it to come on when I put the gear in reverse?
Hello. I have installed this xamera on my car and it worked fine for some time but now it is operating very slowly, basically lagging be it in selecting the menu options or the camera it self. Any idea why this could happen and how to fix it?