I have several Fujikura 90S splicing machines in my company, but four of them are giving the same error, i.e., 'No Electrodes.' I have replaced the electrodes and checked all possible solutions, including updating the firmware, but the error persists. Can you please advise on the possible root cause of this issue, as it seems unlikely that all four machines would experience the same error simultaneously?
Fuji 62s is by far the best splicer made all the new ones, you rely on the machine. Only plus to this splicer is to be able change clamp settings without replacing them. Saying that if you know what your doing you can stip a fibre with no issues with zr motor trouble. For speed i would recommend 62s
I've got a new 90S+ and when I heatshrink the sleeve sticks to the heating element. What temperature and heating time should be setup if polyolefin shrinks at 80-120C?
Hi Sir, I use two cleaver when working with Fujikura 90s plus. One cleaver is CT-50 with wireless and second one is CT-30 without wireless. It's possible to set CT -50 on left or right side on Fujikura 90s ?
In the Fujikura 90S there is no more the button Arc, as was the case for the model 80S. Is there a way to send manually Arcs? I am asking because I want to taper down an optical fiber. The splicer is expecting two fibers, therefore I got the error "too long fibers", when actually I have just one. Nothing happens then. Thanks
Yes, you have to edit splice mode settings in regards to estimated loss threshold. Any value over this will allow for you to re-arc by pressing the button with the lightning icon present after error is shown
Ecf is used when splicing fibre whose core is not concentrically aligned. If this is not on, the two fibres when core aligned and arced will result in cladding becoming aligned and core having a “step” ( there is a better term for this but can’t remember it). When on it prevents this natural line up of the cladding and allows the core to be aligned straighter however claddings will obviously be out of line. This results in less loss overall however will still have a big loss
I'm with the same problem on the left clamp with my 90S There's a little pin that activates de funcion , when I click the pin on the left the machine bips but nothing on the right
Dear I'm using Fujikura R90 splicing machine. I'm facing 1 issue with this machine. I need your help. Whenever I'm splicing SM with this machine my machine braking fiber splice after the arc fusion done.
I think this guy doesn't know how to do splice. End of heating he must to get splice tube out. If he known how to do splice he would use holders and other splice infos. I couldn't bear to watch it.
Good day FAFL, Please I have challenge with my Fujikura 41s motor The error message is X-MOTOR OVERRUN I have tried Diagnostic test, stabilizing the electrode and some cleaning but still persist Please kindly help help with tips of what to do to get the machine back to full function. Looking forward to hearing from you Thank you
how can solve 90s fujikura splicing machine heater oven trouble
I have an open door sensor problem, do you have a tip on how to solve it?
I have several Fujikura 90S splicing machines in my company, but four of them are giving the same error, i.e., 'No Electrodes.' I have replaced the electrodes and checked all possible solutions, including updating the firmware, but the error persists. Can you please advise on the possible root cause of this issue, as it seems unlikely that all four machines would experience the same error simultaneously?
Fuji 62s is by far the best splicer made all the new ones, you rely on the machine. Only plus to this splicer is to be able change clamp settings without replacing them. Saying that if you know what your doing you can stip a fibre with no issues with zr motor trouble. For speed i would recommend 62s
I've got a new 90S+ and when I heatshrink the sleeve sticks to the heating element. What temperature and heating time should be setup if polyolefin shrinks at 80-120C?
Can you splice Single mode and multi mode at the same time
Hi Sir,
I use two cleaver when working with Fujikura 90s plus. One cleaver is CT-50 with wireless and second one is CT-30 without wireless. It's possible to set CT -50 on left or right side on Fujikura 90s ?
In the Fujikura 90S there is no more the button Arc, as was the case for the model 80S. Is there a way to send manually Arcs? I am asking because I want to taper down an optical fiber. The splicer is expecting two fibers, therefore I got the error "too long fibers", when actually I have just one. Nothing happens then. Thanks
I have no clue, use and older model then
Yes, you have to edit splice mode settings in regards to estimated loss threshold. Any value over this will allow for you to re-arc by pressing the button with the lightning icon present after error is shown
Some time my mechine loss above 0.6and x motor overrun ....pls given how to clean mechine
fujikura 90s splicing machine me light on kese kare
ECF , must be on or off for best splice
Ecf is used when splicing fibre whose core is not concentrically aligned. If this is not on, the two fibres when core aligned and arced will result in cladding becoming aligned and core having a “step” ( there is a better term for this but can’t remember it). When on it prevents this natural line up of the cladding and allows the core to be aligned straighter however claddings will obviously be out of line. This results in less loss overall however will still have a big loss
Please can you make video single fiber splice with 250 holder fujikura R90 machine
Price and including shipping to Malaysia?
Hi my splicer stoped to auto close and begin the splicing when fibers are loaded ..any idea why ??
I'm with the same problem on the left clamp with my 90S
There's a little pin that activates de funcion , when I click the pin on the left the machine bips but nothing on the right
Hi Sir,
Can I depend on the estimated splice loss as my final results?
No
It’s inflamed that the door is open and the light stays on
Dear I'm using Fujikura R90 splicing machine. I'm facing 1 issue with this machine. I need your help. Whenever I'm splicing SM with this machine my machine braking fiber splice after the arc fusion done.
call tech support
I’m dealing with the same issue, did you ever find a resolution or is it user error?
Thx for the good review, but why on earth use 720p as resolution from 15years ago, its all pixelated. We have 4k in 2021?
Yeah Lucas! This is awesome...
no fiber holders ?
I think this guy doesn't know how to do splice. End of heating he must to get splice tube out. If he known how to do splice he would use holders and other splice infos. I couldn't bear to watch it.
@@sukranbayraktar7196 it's a 2020 and he is an engineer 🤣🤣🤣
@@sukranbayraktar7196 my tips and tricks # 1- use fiber holders # 2- thermal strippers 🤣🤣🤣, if not available I just pack my stuff and go home.
@@sukranbayraktar7196 thermal stripper and cleaver now are Bluetooth compatible with the machine, so yes, not sure why AFL made this video.
I refuse to do fiber terminations with out the holders and thermal stripers 🤣🤣🤣
Good day FAFL,
Please I have challenge with my Fujikura 41s motor
The error message is X-MOTOR OVERRUN
I have tried Diagnostic test, stabilizing the electrode and some cleaning but still persist
Please kindly help help with tips of what to do to get the machine back to full function.
Looking forward to hearing from you
Thank you
When using the heater I need to press heat, how do i do it where I press down the fibre and the heater window closes and heats
same here
Just set it on auto heat
Hi mate, i am using the Splice + app with the 90S. but now it's showing a pairing error and I can't even use the machine.
dude get hold of tech support, they're awesome
how much sir
i have 4 pieces fitel s220a de-ribbonizer for sale
i have 4 pieces fitel s220a de-ribbonizer for sale
Lucas Mays
Hii
worst machine that if seen so far ! 62s+ & 70s+ are the best that if seen.
Its too far away to see
How do I change my close cover time my 90S has it but it’s blacked out