Earthing and bonding part 1: what are main and equipotential bonding conductors

Поделиться
HTML-код
  • Опубликовано: 16 ноя 2024

Комментарии • 27

  • @TheFella172
    @TheFella172 Год назад +4

    Brilliant video, really helpful and a clear delivery of how and why Bonding and CPC's are used. Well done Adrian.

  • @michaelcox4081
    @michaelcox4081 Год назад +4

    Very good video dude. Clear, concise and easy to understand. Also I think your disclaimer at the beginning hits the nail on the head.

    • @Pure_electrical_training
      @Pure_electrical_training  Год назад +1

      Thank you 🤗
      I get mixed reviews of the disclaimer, but I think the training industry lets people down and someone needs to say something

  • @Savage-lx5yj
    @Savage-lx5yj 3 месяца назад

    Clear and concise! Great use of references! Thanks for sharing!

  • @munafmufc01
    @munafmufc01 Год назад +2

    Brilliant explanation

  • @JShamaal
    @JShamaal 6 месяцев назад

    Thanks for your great videos.
    Well explained.

  • @Rossisearle
    @Rossisearle Год назад +2

    Great video... Keep up good work

  • @ollyburt6477
    @ollyburt6477 Год назад +2

    Lovely vid 👍🏼

  • @matthewfewings6023
    @matthewfewings6023 Год назад +2

    Great video 😊

  • @michaelcostello6991
    @michaelcostello6991 Год назад +1

    If the plastic pipe comes out of ground and changes to copper in house, then does it need to be bonded. ?? I mean it could become live if an electrical fault occurs..

    • @Pure_electrical_training
      @Pure_electrical_training  Год назад +1

      No, it does not need to be bonded as it does not go into the ground (zero potential).
      In this instance, the circuit protective conductor of the appliance will be sufficient

    • @michaelcostello6991
      @michaelcostello6991 Год назад

      I watched another video where a chap suggested a faulty solenoid on a pipe could make the pipe live. Bit scary if the pipe could be sitting there at 230V . Of course with RCD protection one should not get killed if they touch it, but if it was bonded it might be safer ? What are your thoughts on this type of scenario.

  • @arayated5608
    @arayated5608 Год назад +2

    Legend

  • @michaelcostello6991
    @michaelcostello6991 Год назад

    At 4:22 in video it shows measuring voltage on pipe before removing meter. But if the fault current was small i would imagine you would read zero volts. Then it would shoot up to 230v once you break the joint. Im just guessing here. Please clarify if this may happen. That would mean you must always put clamp on pipe before removing a meter regardless of what voltmeter says.

    • @Pure_electrical_training
      @Pure_electrical_training  Год назад +1

      At 4:22 the meter is removed, so I am not quite sure what you mean.
      If you measure with the meter connected, in a fault condition, you would measure a voltage.
      If the meter was removed, in a fault condition, you could read a fault on either side of the meter, but because the current has nowhere to go, it will just sit there until something or someone, completes the circuit.
      And that is the issue

    • @oml81mm
      @oml81mm 3 месяца назад +1

      Not a spark, but surely if there was a current flowing, however small, then there must be a voltage present to make that current flow.

    • @michaelcostello6991
      @michaelcostello6991 2 месяца назад

      Incorrect. The neutral has the same current as the live wire at 230 volts. The neutral is zero volts :)

  • @domrisk3572
    @domrisk3572 Год назад +2

    Promo*SM

  • @johnburns4017
    @johnburns4017 7 месяцев назад

    _through_ *not* _frew._