Conveyor Broken Bearing Replace On Jobsite

Поделиться
HTML-код
  • Опубликовано: 17 ноя 2024

Комментарии • 26

  • @gumin7212
    @gumin7212 10 месяцев назад

    감사합니다 !! 회사에서 베어링이 가끔 고장나서 교체를 해야하는데 하는 방법을 몰라 혼났었는데 덕분에 배웠습니다 !

  • @Leo-b5k8e
    @Leo-b5k8e Год назад

    Okay, that's actually easier to follow 😮

  • @nashcay-an4796
    @nashcay-an4796 2 года назад +1

    good job 👍

  • @Petesworkshop2225
    @Petesworkshop2225 Год назад +7

    Dude.... use a brass hammer whenever working on shaft/bearings.

    • @900fam
      @900fam Год назад

      At least a piece of wood to hit on instead of the bearing itself. Also noticed the grease fitting being trapped on the bottom.. he should of put the bearing on with the fitting on top so that it can get grease when needed.

    • @jambasicskills1970
      @jambasicskills1970  Год назад

      Yes that was correct but sometimes it doesn't follow the basic rules
      Thanks and noted next time@@900fam

    • @brianberson4169
      @brianberson4169 Год назад

      I'm new to it what would u use rubber mallet.

    • @maybe_its_maybelline6381
      @maybe_its_maybelline6381 3 месяца назад +1

      @@brianberson4169rubber mallet is okay but brass hammer works best. Also never hit the bearing like this guy. Get a drift and lay on face of bearing then hit with brass hammer. U should only hit the inner race when working with bearings.

  • @randytodd6309
    @randytodd6309 2 года назад

    Informative 👍

  • @A1_filmsss
    @A1_filmsss Год назад +3

    Next time use a soft face hammer to drive your bearings on and that’s an eccentric locking collar on the bearing. You’re suppose to use a punch in the hole that the set screw doesn’t go into and tap it around in the direction of shaft rotation.

    • @jambasicskills1970
      @jambasicskills1970  11 месяцев назад

      Your correct buddy. video shows how to do it in basic ways but it's up to maintenance guy how they provide proper tools for every project available.. in that time we did just to run it for it will needed it very badly in the middle of busy operation..

  • @chazchampion4281
    @chazchampion4281 7 месяцев назад

    So the bearings don’t need washers?

  • @vishyandypurandat6208
    @vishyandypurandat6208 9 месяцев назад

    Nice job only one thing I'll do differently is using a brass hammer.

    • @jambasicskills1970
      @jambasicskills1970  7 месяцев назад

      Yes Buds, you can use any hammer as long as you are comfortable using it.
      Thanks

  • @grierhawkins8514
    @grierhawkins8514 2 года назад

    That's good 🙂

  • @rhiagorgetv5458
    @rhiagorgetv5458 2 года назад

    😊👍

  • @danknoll3613
    @danknoll3613 Год назад

    He forgot to grease the new bearing.

    • @danknoll3613
      @danknoll3613 Год назад

      And also forgot to put his personal lock on the disconnect.

    • @jambasicskills1970
      @jambasicskills1970  11 месяцев назад

      Yes Buddy. I ms to show in my video about installing LOTO before starting the project.
      Thanks for reminding me appreciated.