So had a similar issue on my rear driver side. I hard wired new connectors on the rear and I also had to bypass the connector all together on the front right. I ended up wiring new pins for the front right right into the abs module To fix this problem. Pins 27 and 28 are at the main module for the front right. My 2011 ram 1500 5.7 4x4 had green with yellow and blue with grey wires to the connector under the driver door for rear driver side. There is another wire that is blue with green stripe. Do not confuse them. If it wasnt for this video i probably wouldnt have found my shorts. 2 years and 5 mechsnics couldnt figure this out. Dodge recommended a whole new body harness to fix this problem and 2 days of labour for 2 service technicians!
Thanks for the info, I’ve changed all four sensors on my ‘10 ram and the same three lights still come on, but only intermittently, I’m now thinking I have a short or broken wire somewhere too and I don’t know which wheel because I don’t have a code reader like you, so I’ll have to find a place that can look it up for me, thanks again!
@@damarcusdjohnson1054t turned out to be a bad wire on the harness of the truck (front passenger side) it was a bit hard to find because the wire was broken inside of its insulator, so it looked good from the outside and still made a good connection, but whenever I drive, that was enough to allow the wire to move around slightly thus breaking that connection and giving me intermittent abs light.
Good video. I have 4 wires from front actuator 2 are positive on 06 Dodge 1500 4+4. Even when switching to 4+4 then same 2 are positive. One is supposed to turn negative to switch on actuator. But doesn't. New actuator. Transfer case definitely kicking in. Continuity tested wires all the way to firewall. All good. Any suggestions please. I've spent every dime on truck and actuator. Any suggestions please. Im a carpenter but common sense. Help .
I have the same issue but it is accompanied by a controller fault on the integrated brake controller module and it only really happens when I punch it on the highway and if I turn truck off it goes away and my cruise Controle didn't work no matter what any idea?
I've been fighting with this same issue for 2 years. If this works I'm going to be so happy. I can finally offload this heap of junk and buy a Ford 😂😂😂
Good morning, I have a problem with my 2006 Dodge Ram 1500 5.7 Hemi. The drives do not work and the ABS lights are on I replaced the sensor on the axle and the front ABS sensor that was indicated by the computer All drive lights are on on the counter and the N diode on the switch, i.e. neutral Has anyone had a similar problem
Thank you for the video,it was very helpful. I was having trouble abs and Esp.thank you God bless you all.
So had a similar issue on my rear driver side. I hard wired new connectors on the rear and I also had to bypass the connector all together on the front right. I ended up wiring new pins for the front right right into the abs module To fix this problem. Pins 27 and 28 are at the main module for the front right. My 2011 ram 1500 5.7 4x4 had green with yellow and blue with grey wires to the connector under the driver door for rear driver side. There is another wire that is blue with green stripe. Do not confuse them. If it wasnt for this video i probably wouldnt have found my shorts. 2 years and 5 mechsnics couldnt figure this out. Dodge recommended a whole new body harness to fix this problem and 2 days of labour for 2 service technicians!
Thank you for taking the time to share this! I have the exact same issue.
Do you get it fix???
I am glad to help.
Did you fix it?
Im dealing with the same issues was told to change my front bearings and sensors $1800 later same problems grr.
Thanks for the info, I’ve changed all four sensors on my ‘10 ram and the same three lights still come on, but only intermittently, I’m now thinking I have a short or broken wire somewhere too and I don’t know which wheel because I don’t have a code reader like you, so I’ll have to find a place that can look it up for me, thanks again!
Yes. Any auto store should be able to read codes for you for free.
@sheild1117 any updates
@@damarcusdjohnson1054t turned out to be a bad wire on the harness of the truck (front passenger side) it was a bit hard to find because the wire was broken inside of its insulator, so it looked good from the outside and still made a good connection, but whenever I drive, that was enough to allow the wire to move around slightly thus breaking that connection and giving me intermittent abs light.
My truck has the same lights on. 2011 dodge ram 1500.. there’s a wire hanging from the passenger back tire.. 4by4 don’t work also..
Good video. I have 4 wires from front actuator 2 are positive on 06 Dodge 1500 4+4. Even when switching to 4+4 then same 2 are positive. One is supposed to turn negative to switch on actuator. But doesn't. New actuator. Transfer case definitely kicking in. Continuity tested wires all the way to firewall. All good. Any suggestions please. I've spent every dime on truck and actuator. Any suggestions please. Im a carpenter but common sense. Help .
Very helpful
Why is his such a common issue in these? my 2012 has the same light display.
I have the same issue but it is accompanied by a controller fault on the integrated brake controller module and it only really happens when I punch it on the highway and if I turn truck off it goes away and my cruise Controle didn't work no matter what any idea?
I have same problem with trailer light also, did you find a solution
Your wheel bearings failing
I've been fighting with this same issue for 2 years. If this works I'm going to be so happy. I can finally offload this heap of junk and buy a Ford 😂😂😂
Did it work?
From one heap to another I guess.
Thanks this gives me a starting point
Also what exhaust are you running
Donde vives tengo el mismo problema yo vivo en tx little elm tx
I have a problem, can start it but instrument cluster dont work.all lights are on. What could be the problem?
Kinda bad enough dealing with rust issues lol and I'm a big dodge fan.started with a 1970 truck lol
Ive changed all my sensors the computer not reading anything but lights still on?
Did U confirm connector plug viability
Thank you for sharing I have a 2011 with the same issue but the serv 4WD only turn on in the morning and it goes away during the day
I got same problem on drivers side
Good morning,
I have a problem with my 2006 Dodge Ram 1500 5.7 Hemi.
The drives do not work and the ABS lights are on
I replaced the sensor on the axle and the front ABS sensor that was indicated by the computer
All drive lights are on on the counter and the N diode on the switch, i.e. neutral
Has anyone had a similar problem
Love the video but I would rather let you fix it than me.....
Having same issue I’ll never buy another Ram in my lifetime
Thank help me a lot and save me $$
This was rough
I have same problem left side
Wire color for left side is green with yellow and green with grey
Did you figured it out?
I had tires rotated and next day I get these same lights
tech broke a sensor or wire I'd bet....