Hi! I want first to thank you for you efforts you doing good and for all this useful information. Is it possible to share with me and step by step hoy to get the image back-up?
@Future Robotics I have some doubts regarding 1.How to communicate robot to Mitsubishi PLC throw CC link 2. How to share input and outputs 3.How to share register values robot to PLC
@@FutureRoboticsChannel Hi.., I am suppose to replace a slave amplifier. To do so, I need to back up all the data from that slave amplifier to the CNC memory. I am quite sure I need to go in PMM setting to back up these data but I don't know the whole process. I will appreciate if have any tutorials/videos on this. thanks in advance.
@@westtigers9140 Oh, that's for FANUC CNC, I do not work with CNC's, so unfortunately I cannot help here. Replacing a servo amplifier on the robot is just plug and play (as long as it's the same model). I would assume it would be the same on the CNC (however I do not know that), amplifier does not hold any data, it's just a power supply. On the robot all dat is stored in the pulse coders and robot memory, so unplugging servo amplifier does not affect any data loss.
Thank you very much for this video. I have some questions about the following topic. Indeed, I would like to restore the information that I recovered with the Backup. What would be the procedure to follow?
@@loicdaven9769 Oh I did not make a video on it yet :-), it's a quite simple process: 1. Get USB with the backup you want to load 2. Go to controlled start 3. Go to FILE 4. if under F4 you see [BACKUP] than click FCTN -> 2. Restore / Backup. Now the option will change to [RESTOR] 5. Select what would you like to restore (if full backup select ALL OF ABOVE) 6. Follow the steps and done :-) You might see that some files will fail to restore, usually those are not important.
@@FutureRoboticsChannel I can do step 4. I don't have the option Restore / Backup when I click FCTN -> 2. I also checked all the options offered by FCTN and I can't find any toggle like Restore / Backup. Is there any other way to change this [BACKUP] to [RESTORE]?
Hi sir, i want first to thank you for you efforts you doing good. Secondly, could you please geave me the link for the simulator CNC fanuc so i can practice virtually more exercices ? Thank you again i appreciate what you do.
How to enter the backup programe in the fanuc because i have a probleme when the robot take the box and returns to position 0 ,then place in the pallet not taking and placing directly
I did not make a video for loading files back yet, but you can do the same thing I'm doing to SAVE single file, but hit LOAD instead of SAVE. So you go to FILE->Select your device (for eg. UD1:)->click ENTER to see all files, navigate to the file you want to load and hit LOAD. It will ask you if you want to override and you say YES. Keep in mind that this file cannot be running or be selected on the robot, because it won't let you load
Is it the gray screen or the color screen where you are selecting image backup ? It's possible that robot froze during the IMAGE backup, you might need to reboot the robot. I'm trying to use MC: for IMAGE bakups as they should be the fastest and safest way to do a backup
@@FutureRoboticsChannel I used UD1 but it was giving me a FILE-064 Unspecified DOS system Error:72 But then when I connected it to UT1 things worked but then while taking image backup it gave a gray screen and froze over there we shut the thing off manually and turned it on It didn’t happen when we took a backup of the 2nd Robot
@@sahilthakkar6432 DOS system Error might mean one of 2 things: -bad UD1 port (you can just replace it) -corrupted software, you might need to re-install the core software to fix that issue going back to your problem, I've seen that happen quite a few times, what system are you using R-30iB or older ? I always recommend using MC card, because I personally never seen one fail.
Very helpful. Thx.These videos are a great refresher.
Glad to hear that 😃
Very good explanation. Thank You.
How about the Maintenance Data backup. Could you explain why we get “exactly” 2 same folders on this type of backup?
VERY GOOD EXPLNTION SIR
Hi! I want first to thank you for you efforts you doing good and for all this useful information. Is it possible to share with me and step by step hoy to get the image back-up?
@Future Robotics I have some doubts regarding
1.How to communicate robot to Mitsubishi PLC throw CC link
2. How to share input and outputs
3.How to share register values robot to PLC
@Future Robotics kindly help me to learn Fanuc robot very indeepth
Thanks in advance
@@sankarsivaraman3785 I'll be more than happy to help, please take a look at my website:
f-robotics.com/consultation
Hi, wondering if you have any tutotrial/Video on PMM (Slave amplifier) back up for Fanuc controller. Thanks
Could you tell me a bit more about what you were thinking ? I'm not sure
@@FutureRoboticsChannel Hi.., I am suppose to replace a slave amplifier. To do so, I need to back up all the data from that slave amplifier to the CNC memory. I am quite sure I need to go in PMM setting to back up these data but I don't know the whole process. I will appreciate if have any tutorials/videos on this. thanks in advance.
@@westtigers9140 Oh, that's for FANUC CNC, I do not work with CNC's, so unfortunately I cannot help here.
Replacing a servo amplifier on the robot is just plug and play (as long as it's the same model).
I would assume it would be the same on the CNC (however I do not know that), amplifier does not hold any data, it's just a power supply. On the robot all dat is stored in the pulse coders and robot memory, so unplugging servo amplifier does not affect any data loss.
@@FutureRoboticsChannel Thanks and I do appreciate you time.
Thank you very much for this video.
I have some questions about the following topic.
Indeed, I would like to restore the information that I recovered with the Backup. What would be the procedure to follow?
I'm assuming you are asking about backup recovery ? or you just need to restore single file ?
@@FutureRoboticsChannel it's about backup recovery
@@loicdaven9769 Oh I did not make a video on it yet :-), it's a quite simple process:
1. Get USB with the backup you want to load
2. Go to controlled start
3. Go to FILE
4. if under F4 you see [BACKUP] than click FCTN -> 2. Restore / Backup. Now the option will change to [RESTOR]
5. Select what would you like to restore (if full backup select ALL OF ABOVE)
6. Follow the steps and done :-)
You might see that some files will fail to restore, usually those are not important.
@@FutureRoboticsChannel I can do step 4. I don't have the option Restore / Backup when I click FCTN -> 2.
I also checked all the options offered by FCTN and I can't find any toggle like Restore / Backup. Is there any other way to change this [BACKUP] to [RESTORE]?
I found it!! Thank you very much!!
sir can i find value of dmr group from backup fanuc r30ib mate pluse
How many programs we can save? Is there any restrictions on no of program we can creat & save?
Backup will safe all of the robot programs, as long as your USB has enough memory to store all of them
Thanks 🙏 you are doing great sir
How many programs we can create ? Is there any limitation on number of programs?
The limitation is you robot memory, there is really a lot of memory
Can u also cover FTP backup
Yeah, sure thing
Hi sir, i want first to thank you for you efforts you doing good.
Secondly, could you please geave me the link for the simulator CNC fanuc so i can practice virtually more exercices ?
Thank you again i appreciate what you do.
Link is in the description of the video:
ruclips.net/video/CqQO51bzyLM/видео.html
How to enter the backup programe in the fanuc because i have a probleme when the robot take the box and returns to position 0 ,then place in the pallet not taking and placing directly
I did not make a video for loading files back yet, but you can do the same thing I'm doing to SAVE single file, but hit LOAD instead of SAVE.
So you go to FILE->Select your device (for eg. UD1:)->click ENTER to see all files, navigate to the file you want to load and hit LOAD.
It will ask you if you want to override and you say YES. Keep in mind that this file cannot be running or be selected on the robot, because it won't let you load
I’m trying to do an Image backup from UT1 and I’m stuck on the main screen where it says auto image backup start please wait
Is it the gray screen or the color screen where you are selecting image backup ?
It's possible that robot froze during the IMAGE backup, you might need to reboot the robot. I'm trying to use MC: for IMAGE bakups as they should be the fastest and safest way to do a backup
@@FutureRoboticsChannel I used UD1 but it was giving me a FILE-064 Unspecified DOS system Error:72
But then when I connected it to UT1 things worked but then while taking image backup it gave a gray screen and froze over there we shut the thing off manually and turned it on
It didn’t happen when we took a backup of the 2nd Robot
@@sahilthakkar6432 DOS system Error might mean one of 2 things:
-bad UD1 port (you can just replace it)
-corrupted software, you might need to re-install the core software to fix that issue
going back to your problem, I've seen that happen quite a few times, what system are you using R-30iB or older ? I always recommend using MC card, because I personally never seen one fail.
@@FutureRoboticsChannel I’m using R-30iB Plus
And How can i load the backups? And how can i load the copied Data to a new robot? Should i copy paste all data to MD:?
The correct way would be to restore the backup, I have not made a video on it yet
@FutureRoboticsChannel could you please make that video ASAP ?
@@lboy6191 Feel free to schedule a consultation with me at: f-robotics.com/consultation
I can assist you remotely with any robotic issues
Hello Future robots, you said to ask what i am interested in, well i am interested in practical know how operation of the robots!!!
Interesting tutorial! thanks.
How to make a robot go back home on the machine panel
I'm not quite sure what you are asking about.
Do you want to know how to add MACRO function ?
Hey bro do u have Turkish videos? İ need. Or pdf all everything
I do not, I do not speak Turkish unfortunately 🙂
What's the name of the software you are using? Do you need a teach pendent to do a backup, or can you do it from the software?
Thanks!
The software is called FANUC Roboguide, you don’t need a tech pendant to use the software all is simulated on your PC
And if you dont have a USB?? but you have a PCMCIA??????
you follow the same steps but you use MC instead of UD1 or UT1.
MC Card is PCMCIA