You couldn’t ask for better step by step instructions! Went in almost exactly as shown. My new pump we slightly wider which made it more difficult to secure The pump to the base. I ended up using a small crescent to tighten the left screw. He made it very simple for anyone to complete.
Very helpful step by step video. I’ve replaced the washer pump and the last replacement was November 2019. Today going to replace it again and watching this video again 😊
Thanks a lot. I was afraid of the dissasembly procedure, but with your professional explanation and enough time at home was a matter of patience and care. The nearest service shop from here is at 2 hours and we can't leave to look for parts; IT's prohibited due to the Coronavirus. I appreciate a lot your help, And my family also. I fixed our washer and clean the clogged trap of the drain hose and some wires that blocked the pump. Please, as possible stay at home. Good luck and success in your service job.
To reduce the water mess, remove the two pump mounting bolts. Then lift the pump assembly, hoses attached, and slip a ~2" deep baking pan under the pump. If the machine had been pumped out (I replaced my pump when it started making noise), the pan should hold all of the water when the discharge hose is removed (remove the hose slowly as there is a little pressure). If the pump failed and the machine still contains a lot of water, the pan can act as a sump for a wet vac. In my case, about 98% of the water was contained in the baking pan (some escaped during hose manipulation). I did this on an older model, but do not see where this process cannot be done with this model as well.
I was just going to ask this. Once they removed the front door rubber piece, I saw myself never being able to get that ring back on. We did ours from back. Requires a little more reaching but seems like a lot less work.
@AppliancePartsPros just want to say thank you so much for making this! This is the same under-tub layout as my Kenmore 90-series. My pump went out and I followed your video step by step and it was extremely informative. The only thing is the hoses go backwards on this pump for some reason aside from the original layout of the original part. Everything works great now. Thank you so much for the video!
At 4:32, you can see the red rubber flapper valve is installed on the top side of the old pump’s drain spout. But when you install the new one, it’s clear at 5:23 that the new pump has the valve attached from the bottom side of the spout. Does it make a difference how it’s attached?
Remove the balance weight from the around the drum,5 11mm and 5 min will save you a ton of hassle trying to get the clamps back on. Also while you have it apart clean the filter out.
What's the part number for the black house that the drain pump attaches to? I took my pump off and could see a clear/grey plastic filter piece inside that black hose. Not sure if that's supposed to be in there or not? Or did it come loose off of somewhere else? No parts diagram references the filter piece.
@Peter L sounds like you're curious. I turned off the water and gas/heat. I then dismantled the washer after a series of other steps and then I changed the pump with no issue. The answer to the question is that I'd have city water pumping through my home. Would have appreciated an actual answer but I guess the internet transacts in condescension. We all start from somewhere. But hey the video wasn't bad.
Thanks a lot! 9 years and your video is still helpful!!
You are welcome. Glad we were able to help you out. If there is anything we can help you with in the future please let us know.
You couldn’t ask for better step by step instructions! Went in almost exactly as shown. My new pump we slightly wider which made it more difficult to secure The pump to the base. I ended up using a small crescent to tighten the left screw. He made it very simple for anyone to complete.
Very helpful step by step video. I’ve replaced the washer pump and the last replacement was November 2019. Today going to replace it again and watching this video again 😊
Glad you were able to fix your issue! If there is anything we can help you with in the future please let us know.
Extremely well done! Clear and concise, both the video and the step-by-step instructions! Thank you so much!
You are very welcome. If there is anything we can help you with in the future please let us know.
Thanks a lot. I was afraid of the dissasembly procedure, but with your professional explanation and enough time at home was a matter of patience and care. The nearest service shop from here is at 2 hours and we can't leave to look for parts; IT's prohibited due to the Coronavirus. I appreciate a lot your help, And my family also. I fixed our washer and clean the clogged trap of the drain hose and some wires that blocked the pump. Please, as possible stay at home.
Good luck and success in your service job.
To reduce the water mess, remove the two pump mounting bolts. Then lift the pump assembly, hoses attached, and slip a ~2" deep baking pan under the pump. If the machine had been pumped out (I replaced my pump when it started making noise), the pan should hold all of the water when the discharge hose is removed (remove the hose slowly as there is a little pressure). If the pump failed and the machine still contains a lot of water, the pan can act as a sump for a wet vac. In my case, about 98% of the water was contained in the baking pan (some escaped during hose manipulation). I did this on an older model, but do not see where this process cannot be done with this model as well.
Great instructional video. The only thing i would've included would've been cleaning out the "lint or coin trap" at the same time.
You can replace the drain pump from the back panel. Saves a lot of work.
I was just going to ask this. Once they removed the front door rubber piece, I saw myself never being able to get that ring back on. We did ours from back. Requires a little more reaching but seems like a lot less work.
@AppliancePartsPros just want to say thank you so much for making this! This is the same under-tub layout as my Kenmore 90-series. My pump went out and I followed your video step by step and it was extremely informative. The only thing is the hoses go backwards on this pump for some reason aside from the original layout of the original part. Everything works great now. Thank you so much for the video!
Glad the video helped you out on the Kenmore washer!
Thank you for this!!!! This saved me so much money by being able to repair it myself!
Very professional and makes it look easy. The guy reminds me of Gomer Pyle (forgot his real name but he was not a bit dumb, just a great actor)
This was a great step by step instruction. Thank you
Thank you for sharing this knowledge we are all very grateful
At 4:32, you can see the red rubber flapper valve is installed on the top side of the old pump’s drain spout. But when you install the new one, it’s clear at 5:23 that the new pump has the valve attached from the bottom side of the spout. Does it make a difference how it’s attached?
The camera angle is different when he's showing how to install the new one, but the part is oriented the same as the original.
Remove the balance weight from the around the drum,5 11mm and 5 min will save you a ton of hassle trying to get the clamps back on. Also while you have it apart clean the filter out.
Thank you for the tips. If you have any questions or need help with anything please let us know.
What's the part number for the black house that the drain pump attaches to? I took my pump off and could see a clear/grey plastic filter piece inside that black hose. Not sure if that's supposed to be in there or not? Or did it come loose off of somewhere else? No parts diagram references the filter piece.
Thank you kindly for the video
You are very welcome.
Question, do I need to turn off the water coming through the water hoses before starting work here?
@Peter L sounds like you're curious. I turned off the water and gas/heat. I then dismantled the washer after a series of other steps and then I changed the pump with no issue. The answer to the question is that I'd have city water pumping through my home. Would have appreciated an actual answer but I guess the internet transacts in condescension. We all start from somewhere. But hey the video wasn't bad.
Great info but you really need to increase the bass on your audio.
Where to order new part
You can place an order through our website, or you can call us at 1-877-477-7278 to place an order over the phone.
What else would cause washing machine to leak 🤔
Bad video , you overcharge for labor!! It can all be acces from bottom and this job can be done in 20 minutes start to finish
Our videos are just to help give you a general idea on how to do the repair. If you have any questions please let us know.
That machine is extremely heavy. This guy makes it look like cake walk. A few minutes?????? Come on!