Did you notice you get different rates of throw depending on the mode the gyro is in? I found a little guide helps stop the very thin control rods from flexing too. Like the prop mods might have to have a go!
Yes, travel is different in the different modes, pretty much the same as SAFE in E-flite planes. I did think about some guides for the rods as well, it feels a bit mushy but I wasn't sure if it's the radio or the control rods.
Yeah, it's a bit harder to get these small props in different sizes plus being 1s there's not much to play with in terms of power. I'm pretty happy with it, just need tail steering and a proper radio.
Excellent video! I have this one in red, it's very easy to see in the sky. I broke the nose a few times in crashes so I beefed up the fuselage with two nose-to- tail carbon fibre strips. The next weakest point was the motor mount so I reinforced that with a metal plate, formed into a casing under and behind the motor. Then I braced the landing gear to the carbon strips, it kept bending, very annoying. It's now pretty much bullet proof. And then I went a little crazy and made the tailwheel steerable! It works perfectly! The mods added 14 grammes to the take off weight and didn't noticeably affect the centre of gravity.
To test the difference in thrust between the props, you could tie the tailwheel to a set of scales, with an L shaped lever to get downward pressure, and see how much it pulls.
I wanted the red but after 3 weeks of waiting I switched to blue, it was in stock. Extensive list of mods you have there. The steerable tail wheel is something I need to do for sure. And you are right with the thrust test, I might need to do it. Thanks for subscribing!
@@A.M.-RC i removed the tailplane, took out the tailwheel, tried to straighten the wire but it broke so I ended up with a shorter but straight wire. Drilled a hole through the plastic mount and made a lever out of an old heli tail rotor, which I then connected to the rudder servo. A tricky job but it worked out perfectly. Note: to get a sharper turn, use the advanced mode on the transmitter while on the ground. Before take off, I always switch to stabilized mode. Hope this helps.
I ordered the rtf kit for my son to become his first rc airplane. But what battery can fit the battery compartment? Would a 1S800mAh fit in it? Would a rating of 20-30C constant drain suffice? Nice review, thanks! Cheers, Ken, Finland
Thanks for watching and commenting! I just tested if my Spektrum 800mah 1s would fit and it doesn't. As far as discharge I'm sure 20C would be enough, as much as these ratings can be trusted. Hope your son has fun with it, it's not the best plane but it sure is durable and the price is great for what it offers.
Did you notice you get different rates of throw depending on the mode the gyro is in? I found a little guide helps stop the very thin control rods from flexing too. Like the prop mods might have to have a go!
Yes, travel is different in the different modes, pretty much the same as SAFE in E-flite planes. I did think about some guides for the rods as well, it feels a bit mushy but I wasn't sure if it's the radio or the control rods.
Have mine ordered, can’t wait! Great video 👍🏻
Thanks! I was really excited for this one as well, it's not perfect but it's good.
The tripple blade looks good and running cold is perfect. May even be able to prop up a little more but seems to handle great!
Yeah, it's a bit harder to get these small props in different sizes plus being 1s there's not much to play with in terms of power. I'm pretty happy with it, just need tail steering and a proper radio.
Ohhh well done with the modifications Alex. Now you will have to cut in some flaps. Why do they always put power lines on the runway.👏👏👏
Flaps would be good, it lands a little fast. At least now I know it can take a crash.
Flaps, eh? Mmmh... you'd have to split the ailerons and add a servo. Not sure if the stock receiver and transmitter would accommodate for that.
Nice work on the prop change, the 3 bladed prop looks and performs better, you were so lucky she did'nt get caught up in the power lines....jeff.
That would've probably been the end of it if it got caught. Lucky me it's pretty bouncy 😄
@@A.M.-RC Lucky indeed! I got mine out of a tree once, using a very long telescopic fishing rod! :)
Man, those power lines will reach out and grab you, just like around here.🤪
Oh yeah, I thought it would have more punch to get away. It didn't 😄
Nice video!! Would like to see more mods!
Thanks! I hope I'll be able to get more out of it, I really like this airplane.
@@A.M.-RC I have one as well, it was my first time flying without gyro on an rc plane! Really good for beginners!
Yes, it's a decent beginner plane and it can get you far into the hobby. Hope you have many great flights with yours!
@@A.M.-RC Thank you!
Alex the 3 blade prop looks sharp, nice mod. Jeff in LA USA
Yup, I like it even though the 2 blade looks more scale. Thanks for watching!
Excellent video! I have this one in red, it's very easy to see in the sky. I broke the nose a few times in crashes so I beefed up the fuselage with two nose-to- tail carbon fibre strips. The next weakest point was the motor mount so I reinforced that with a metal plate, formed into a casing under and behind the motor. Then I braced the landing gear to the carbon strips, it kept bending, very annoying. It's now pretty much bullet proof. And then I went a little crazy and made the tailwheel steerable! It works perfectly! The mods added 14 grammes to the take off weight and didn't noticeably affect the centre of gravity.
To test the difference in thrust between the props, you could tie the tailwheel to a set of scales, with an L shaped lever to get downward pressure, and see how much it pulls.
I subscribed to your channel :)
I wanted the red but after 3 weeks of waiting I switched to blue, it was in stock. Extensive list of mods you have there. The steerable tail wheel is something I need to do for sure.
And you are right with the thrust test, I might need to do it.
Thanks for subscribing!
@@A.M.-RC i removed the tailplane, took out the tailwheel, tried to straighten the wire but it broke so I ended up with a shorter but straight wire. Drilled a hole through the plastic mount and made a lever out of an old heli tail rotor, which I then connected to the rudder servo. A tricky job but it worked out perfectly. Note: to get a sharper turn, use the advanced mode on the transmitter while on the ground. Before take off, I always switch to stabilized mode. Hope this helps.
Thanks, I will have to do it soon.
Nice woek with the little adapter. I meed to get a 3d printer to do the same for my small props.
There's so many cool things you can 3D print, hope I get to finish and test my 3D printed planes soon.
@@A.M.-RC awesome can't wait to see!
Awesome video thanks for posting.😊😊👍👍🛩🛩🛩✈✈✈🛰🛰🛰🛰
Thanks for watching friend!
nice little plane,flies great 👍 👌 😀
It's better now for sure, and I hope I can make it even better.
Beautiful plane💙💪😉
Thanks friend!
I ordered the rtf kit for my son to become his first rc airplane. But what battery can fit the battery compartment? Would a 1S800mAh fit in it? Would a rating of 20-30C constant drain suffice? Nice review, thanks! Cheers, Ken, Finland
Thanks for watching and commenting!
I just tested if my Spektrum 800mah 1s would fit and it doesn't. As far as discharge I'm sure 20C would be enough, as much as these ratings can be trusted.
Hope your son has fun with it, it's not the best plane but it sure is durable and the price is great for what it offers.
Nice Crash... Test my Friend ❤!!!
🐻❄️🏁🐼👌🏻
Have a Great Weekend 🎉
Thanks Panda! You too!
🐻❄️🏁🐼👌🏻
Cheers my Friend
Very good work😀👌
Thank you friend!
@@A.M.-RC 😀👍👍