You can test it without load. If it runs normally, you can try to drive the load. If the motor heats up normally, you don't need to remove the capacitor.
Can VFD connect with two windings capacitor motor?, i have VFD only L1, L2, and two windings capacitor motor, can i connect it with capacitor on vfd output?
Is it started at full speed so the centrifugal switch stops and avoids overheating? Also can this work on a 1.1KW 2 Pole 240V 1.5HP Dual capacitor motor?
Could this be used to shift phase of equipment like a 3D printer where phase of equipment causes flickering of lights etc? To isolate and move equipment off 60 hz to say 59 hz
@@ATOcom while yes I am. no I am not. that is very expensive for my goal which is to vary the frequency of the power from 120 or 240V 60hz AC to maybe 59 hz or 61hz just some variable "off" the natural frequency of the mains power. where as those look like very high end ways to provide power that replicates that of overseas locations. by and large if you have something like electronics or a motor it doesnt so much care if it sees 50 or 60 hz. but since my power is 60hz my light bulbs are flickering at 60 hz and if I run say a 3D printer which is drawing current for the heaters and causing a harmonic then I get to live in a club which my printer is running. where as a VFD possibly I could use to modulate the frequency the 3D printer is seeing so maybe the lights wouldnt strobe. I do have an ATO drive for my drill press but I assumed that I shouldnt run that and tap a single leg of it to run q 3d printer which is why I am wondering how a single phase would do if it's not powering a motor but instead just an AC to DC power transformer at something near a 60 hz setting
Can use. However, it is not recommended to directly adjust the speed. When a single-phase motor is connected to a single-phase VFD, the low torque is not strong.
Thanks of millions
Should i need to remove motor capacitor before installing VFD?
You can test it without load. If it runs normally, you can try to drive the load. If the motor heats up normally, you don't need to remove the capacitor.
I want vfd required, vfd specification below.
Input & Output volt 110Ac
Frequency 60Hz
1.5kw capacity
Can VFD connect with two windings capacitor motor?, i have VFD only L1, L2, and two windings capacitor motor, can i connect it with capacitor on vfd output?
Could it run at 5hz frequency
Is it started at full speed so the centrifugal switch stops and avoids overheating? Also can this work on a 1.1KW 2 Pole 240V 1.5HP Dual capacitor motor?
Yes, it is recommended to run at a speed higher than 80% of the motor's rated speed to allow the centrifugal switch to open.
Can we use any 3 phase VFD to control 1 phase motor?
Ordinary VFD does not work, you can try turning off the phase loss protection.
Could this be used to shift phase of equipment like a 3D printer where phase of equipment causes flickering of lights etc? To isolate and move equipment off 60 hz to say 59 hz
Are you referring to a frequency converter?
Check out this link:
www.ato.com/1-phase-frequency-converter
www.ato.com/3-phase-frequency-converter
@@ATOcom while yes I am. no I am not. that is very expensive for my goal which is to vary the frequency of the power from 120 or 240V 60hz AC to maybe 59 hz or 61hz just some variable "off" the natural frequency of the mains power. where as those look like very high end ways to provide power that replicates that of overseas locations. by and large if you have something like electronics or a motor it doesnt so much care if it sees 50 or 60 hz. but since my power is 60hz my light bulbs are flickering at 60 hz and if I run say a 3D printer which is drawing current for the heaters and causing a harmonic then I get to live in a club which my printer is running. where as a VFD possibly I could use to modulate the frequency the 3D printer is seeing so maybe the lights wouldnt strobe. I do have an ATO drive for my drill press but I assumed that I shouldnt run that and tap a single leg of it to run q 3d printer which is why I am wondering how a single phase would do if it's not powering a motor but instead just an AC to DC power transformer at something near a 60 hz setting
Currently, the only devices that can achieve the functions you mentioned are the ones I sent you the link to earlier...@@bryceg5709
59 hz is a very bad choice, because there is gonna be 1hz flickering ^^, you know, one second they match, the other they dont.
can this be used on a single phase 240 v milling machine or small lathes
Can use. However, it is not recommended to directly adjust the speed. When a single-phase motor is connected to a single-phase VFD, the low torque is not strong.
1 phase motor likes pump has a running capacitor..how to connect wire to the motor?
You can directly connect to the VFD without removing the capacitor. The operating speed is more than 80% higher than the rated speed of the motor.
apakah kompresor tidak panas?
Can you reverse it?
You can only reverse the rotation of the motor through the wiring indicated on the motor nameplate.
Price?? Its possible sensor control
Price kitna hain
For the latest price, visit here: www.ato.com/single-phase-vfd
Taylor Melissa Young James Martin Ruth
availably in india? whats the price ? what is the contact number
This link，www.ato.com/single-phase-vfd
Bol k btaty to acha tha....smjh nhi i