FRANCIS EP.4 | Velaworks Front DIY Slam Kit | Installing control arm pockets, upper plates and bags.
HTML-код
- Опубликовано: 10 сен 2024
- This step-by-step will show you how to install Velaworks Step Notch on your 63-72 C10! This notch is a must if you're bagging your C10! Check out www.simplec10.co for parts, merch, and DIY tutorials!
Parts mentioned in this video: (Support the channel by purchasing from my website!)
Velaworks Front DIY Slam Kit: simplec10.mysh...
Here are a few things that the new website offers (www.simplec10.co)
→ Exclusive Parts for your C10.
→ DIY Tutorials, including my step-by-step "Air Ride Guide".
→ Links to all my favorite C10 parts with reviews!
→ Build Profiles for all my past builds.
→ Simple.C10 Merchandise.
Thank you for your support and encouragement!
→ Become a Simple.C10 Subscriber!
→ Website: www.simplec10.co
→ Instagram: / simple.c10
→ Facebook: / simplec10
→ My Channel Home Page: @simple.c10
→ As an eBay/Amazon Associate, I earn from qualifying purchases.
If the video was helpful, remember to give it a "thumbs up" and consider subscribing.
Thank you for this video! There's not many videos about cupping the lowers.
I noticed that! I’m glad I’m able to help some people. It’s not difficult but there are a lot of things I was worried about the first time I did it.
Nice job
Thank you
Use a silver or gold Sharpie. Great video!
Thanks! I started using a white construction crayon after this. Works good too!
Very good information Thank you
Thanks for watching. I appreciate it.
Nice video! Thank you
Thanks!
Thanks for video!! Keep going on bro
Thanks!!
Have you used the switch suspension control arm you sell on any of your builds? Thought?
I will install it on Francis soon and have a video about it!
Hi - looking for info on how you connect air line to fitting after mounting the top bracket to the crossmember ? It must be easy because no one mentions how to get the line in there but I've never done it before. Thanks
DIY Bagged C10 Airline Organization | How do I run my airlines?
ruclips.net/video/17p3q6qybw0/видео.html
Hi simple c10, i have a 70 c10, have 2600 air bags, im thinking to cup my lower control arms, but need to make sure it will make difference between have it cupped or not, because if i want to drive it low it gets rought driving , have 2 1/2” drop spindles too, if i cup it, will improve suspencion softness or is the same? Thank u love your work
Cupping your lowers allow the bag to mount to the bottom of the a air allowing you to have better pressure at low heights. It’s a must.
What is the biggest tire these will lay out with? I want to run a 265 40 22. I believe the tire you use is a 30 series?
I wouldn’t run anything bigger than a 255/30/22 on the front. You could run a 265 on the back but clearance is a big factor on anything bigger.
@@SIMPLE.C10 I don't think a wheel would last long around here with a tire that small. A 35 series is bad enough on a car in this area with all the oilfield traffic creating potholes.
Subscribed
Thanks!!
You mentioned you used 2.5" drop spindles. Would 3" drop spindles help you get closer to laying frame?
Great question. The answer is No. Because my control arms hit the ground before the frame does. The setup I run will get you as low as you can go without sectioning the crossmember, zing the frame, or getting an aftermarket drop member.
@@SIMPLE.C10 thank you for the reply brother!!!
Hey man love the videos my question im got a 83 c10 and i see in your video your using stock uppper and lower my question is how many shimes did you use for the upper cause mine as it sits with no bags has 11 damn shives
I usually have about 3 or 4 but it all depends.
Hi Justin,
Using the Same front vela works upper and lower pats kit. My question is what will become of the front sway bar, as cup is so close to attachment points… great video thanks in advance.
Hey buddy! My name is Travis. I don’t use a sway bar on my builds.
Appreciate your videos!🙏🏽
Do you have any suggestions for a truck with tubular c.arm? I swapped them out with a POL “stage 3” tubular upper and lower. Not sure how go about it. Any info would be greatly appreciated! 🙏🏽
What specifically do you need help with?
did you center the ring to the center of the spring pocket or you just do the 1 inch and one inch on sides?
I did exactly what the video shows and everything aligned perfectly. This is my third truck I’ve cupped.
@@SIMPLE.C10 ok. My truck is a 70 and I’m getting ready to do mine but was wondering how I would line up the cups.
Just follow my lead and everything will line up.
Where did you get the bag fittings? Also are they the swivel type?
They came in my air ride kit but you can get them from Amazon too. 1/2 inch not to 3/8 push swivel
@simple.c10 Do you need the bump stop on the upper control arm?
You can leave it but I remove mine without issue.
Looks very nice!
Does the truck ride’s smooth?
I’m looking for smooth ride not sure if I should use coil over or bags..what’s your opinion?
Bags done well ride very smooth. I’ve never had coil overs.
How did you remove the bracket for the bump stop on the lower control arm?
Drilled out the spot welds.
Sorry, I didn't drill big enough! Went one size bigger with my drill bit and bam! They are off
I have a 65 c10. I want to go low but don’t want to get bags. Any product recommendations?
Cpp drop kit or adjustable coil overs.
Does it still lock up all the way in height, or do you lose height?
Plenty of height!
I love watching your videos, learned a lot so far about airbag . I would like to bag a 1959 Chevy Apache with a 5 x 2 tube frame with a Camaro stub. Do you think I would just follow your procedure on cupping my lower control arms I don’t see much on anybody bagging with a Camaro stub. Any guidelines on this I would sure appreciate thank you.
I’m not familiar with it either. I couldn’t say without looking at it.
If you look at some videos for bagging an s 10 truck they are pretty similar. it should put you in the ball prk.
Will the cpp lower control arms get me as low as cupping stock lower control arms?
Yes they will but you have to cut off the bumpstop bracket. I have a video on how I did it. Not hard. If I could do it all over again I would get the ridetech strong arms instead of fabbing the cpp.
@@SIMPLE.C10 when you installed the cpp lower control arm did you have to move lower shock bracket back ,I installed mine just looks like it's towards the wheel more then stock in which would put shock in more of an angle?
No I didn’t. I used a drop shock and it worked perfectly.
What years of C10 do those Velaworks cups and upper plates work with? Only up to '72 or also with square bodies?
I believe the lower cup work with 63-72 and squares since it’s a universal cup. I’m not sure about the upper bracket. I’ll check with Walter at Velaworks.
@@SIMPLE.C10 I'm interested to know too. Considering air on my '79 and this looks like a good product.
The lower cups will work!
I was curious, what paint did you use that was thick and shiny like that was it a frame paint if you could let me know thank you
It’s linked on my website. Www.simplec10.co under featured products
How deep was the cups you used ?
I believe they’re 2 inch
Hello simple c10, loving your content. Much appreciated for your efforts. Do you have the diameter of that cup/pipe? Kind regards from south africa 🇿🇦 DanPegLegBuilder
8.25 inside diameter.
Well alright alright .....
Yessir
So with this install will lay frame?
What the biggest wheel I can use to lay frame….
Go back and watch my bagging on a budget and air ride 101 videos. This will help explain that this setup doesn’t “lay frame”. It gets you as low as you can go on your stock parts. To lay frame you would need to have a drop member, Z the frame, or section the crossmember.
@@SIMPLE.C10 thanks sir will do
What is bag is that
The kit I use is from airslamit.com. It’s a 2600 in the front. ebay.us/Pc16vs
Hi simple c10, what is the depth of the cup? I know is 8 1/4” inside diameter, or do you have a link to purchase the cups?? Ty keep recording videos bro👌👌
9:33 Duh. Just notch the plate.
Thanks.